Re: [PATCH] PCI: Set device power state to PCI_D0 for device withoutnative PM support

[Stefano Stabellini]

On Tue, 18 Oct 2011, Ajaykumar Hotchandani wrote:
> On 10/13/2011 08:00 PM, Stefano Stabellini wrote:
> > On Mon, 10 Oct 2011, Ajaykumar Hotchandani wrote:
> >> On 10/06/2011 09:47 PM, Stefano Stabellini wrote:
> >>> On Thu, 6 Oct 2011, Yinghai Lu wrote:
> >>>> On Thu, Oct 6, 2011 at 3:39 AM, Stefano Stabellini
> >>>> <stefano.stabellini@xxxxxxxxxxxxx>   wrote:
> >>>>> I had the same issue and sent a patch a while ago to fix it, adding
> >>>>>
> >>>>> current_state = PCI_D0 in acpiphp_glue.c:register_slot
> >>>>>
> >>>>> it is strange that this does not work for you:
> >>>>>
> >>>>> http://marc.info/?l=linux-kernel&m=129891002722845&w=2
> >>>> So guest os has to load acpiphp instead of pciehp?
> >>> maybe pciehp needs to make sure that current_state = D0 in
> >>> pciehp_enable_slot, like acpiphp does
> >> Here, acpi hotplugging is involved.
> >> With your change in register_slot(), device will have proper power state when module is being loaded for the first time after booting.
> >> However, while unload of pci module; following is in pci_device_remove():
> >>           if (pci_dev->current_state == PCI_D0)
> >>                   pci_dev->current_state = PCI_UNKNOWN;
> >>
> >> So, device power state state will remain PCI_UNKNOWN while module is loaded again. Subsequently, MSI write will do nothing.
> > Does this mean that this bug would actually trigger even with devices that
> > do support _EJ0 and power management?
> Nope. I don't have system to verify. But, for the scenario you mentioned 
> (device is hot pluggable, acpi bus power manageable and device with 
> pm_cap supported; if I understand it correctly), following is what I 
> think should happen:
> - Inside pci_platform_power_transition(), 
> platform_pci_power_manageable() will be successful. However, 
> platform_pci_set_power_state() will fail (as device supports EJ0) and 
> subsequently pci_update_current_state() will not get called.
> - So, current power state of device will not be read and power state of 
> device will remain PCI_UNKNOWN.
> - Now, pci_raw_set_power_state() will get called. Here, as current power 
> state is PCI_UNKNOWN, pci_write_config_word() will be called with pmcsr 
> value as 0. As, last two bits of pmcsr is 0, written power state of 
> device will be PCI_D0 now. And subsequently, dev->current_state will be 
> assigned as PCI_D0 (by using pci_read_config_word() ).

OK, I understand.


> > Because acpi_pci_set_power_state won't set current_state to PCI_D0
> > because the "hotplug driver will take care of _PSx" (see
> > 10b3dcae0f275e2546e55303d64ddbb58cec7599) but the hotplug driver is not
> > actually invoked when loading again a driver module of an existing pci
> > device (the example you mention above)?
> Can you please elaborate more on this?
> acpi_bus_set_power() will update state of acpi_dev (ACPI_STATE_XX) and 
> not pci_dev (PCI_XX).
> And here, issue lies with current_state of pci_dev.

I agree, I was merely stating again what the problem is.

BTW I am OK with your patch.
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/