[PATCH 06/10] MXS-DMA : add more flags for MXS-DMA
From: Huang Shijie
Date: Thu Jan 19 2012 - 01:15:33 EST
[1] Background :
The GPMI does ECC read page operation with a DMA chain consist of three DMA
Command Structures. The middle one of the chain is used to enable the BCH,
and read out the NAND page.
The WAIT4END(wait for command end) is a comunication signal between
the GPMI and MXS-DMA.
[2] The current DMA code sets the WAIT4END bit at the last one, such as:
+-----+ +-----+ +-----+
| cmd | ------------> | cmd | ------------------> | cmd |
+-----+ +-----+ +-----+
^
|
|
set WAIT4END here
This chain works fine in the mx23/mx28.
[3] But in the new GPMI version (used in MX50/MX60), the WAIT4END bit should
be set not only at the last DMA Command Structure,
but also at the middle one, such as:
+-----+ +-----+ +-----+
| cmd | ------------> | cmd | ------------------> | cmd |
+-----+ +-----+ +-----+
^ ^
| |
| |
set WAIT4END here too set WAIT4END here
If we do not set WAIT4END, the BCH maybe stall in "ECC reading page" state.
In the next ECC write page operation, a DMA-timeout occurs.
This has been catched in the MX6Q board.
In order to fix the bug, we should let the driver to
set the proper DMA flags in the DMA command structrues.
So add the new flags for MXS-DMA.
The driver can use these flags to control the DMA in a more flexible way.
Signed-off-by: Huang Shijie <b32955@xxxxxxxxxxxxx>
---
include/linux/mxs-dma.h | 26 ++++++++++++++++++++++++++
1 files changed, 26 insertions(+), 0 deletions(-)
diff --git a/include/linux/mxs-dma.h b/include/linux/mxs-dma.h
index 203d7c4..3ef73b8 100644
--- a/include/linux/mxs-dma.h
+++ b/include/linux/mxs-dma.h
@@ -11,6 +11,32 @@
#include <linux/dmaengine.h>
+/*
+ * The drivers use these flags for ->device_prep_slave_sg() :
+ * [1] If there is only one DMA command in the DMA chain, the code should be:
+ * ......
+ * ->device_prep_slave_sg(MXS_DMA_F_WAIT4END);
+ * ......
+ * [2] If there are two DMA commands in the DMA chain, the code should be
+ * ......
+ * ->device_prep_slave_sg(0);
+ * ......
+ * ->device_prep_slave_sg(MXS_DMA_F_LASTONE);
+ * ......
+ * [3] If there are more than two DMA commands in the DMA chain, the code
+ * should be:
+ * ......
+ * ->device_prep_slave_sg(0); // First
+ * ......
+ * ->device_prep_slave_sg(MXS_DMA_F_APPEND [| MXS_DMA_F_WAIT4END]);
+ * ......
+ * ->device_prep_slave_sg(MXS_DMA_F_LASTONE); // Last
+ */
+#define MXS_DMA_F_APPEND (1 << 0)
+#define MXS_DMA_F_WAIT4END (1 << 1)
+
+#define MXS_DMA_F_LASTONE (MXS_DMA_F_APPEND | MXS_DMA_F_WAIT4END)
+
struct mxs_dma_data {
int chan_irq;
};
--
1.7.0.4
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/