[PATCH v6 3/3] USB: ohci-nxp: Support for LPC32xx
From: Roland Stigge
Date: Sat Mar 10 2012 - 20:47:19 EST
This patch adds support for the LPC32xx to ohci-nxp
Signed-off-by: Roland Stigge <stigge@xxxxxxxxx>
---
drivers/usb/host/ohci-hcd.c | 2
drivers/usb/host/ohci-nxp.c | 132 ++++++++++++++++++++++++++++++++------------
2 files changed, 99 insertions(+), 35 deletions(-)
--- linux-2.6.orig/drivers/usb/host/ohci-hcd.c
+++ linux-2.6/drivers/usb/host/ohci-hcd.c
@@ -1050,7 +1050,7 @@ MODULE_LICENSE ("GPL");
#define PLATFORM_DRIVER ohci_hcd_at91_driver
#endif
-#ifdef CONFIG_ARCH_PNX4008
+#if defined(CONFIG_ARCH_PNX4008) || defined(CONFIG_ARCH_LPC32XX)
#include "ohci-nxp.c"
#define PLATFORM_DRIVER usb_hcd_nxp_driver
#endif
--- linux-2.6.orig/drivers/usb/host/ohci-nxp.c
+++ linux-2.6/drivers/usb/host/ohci-nxp.c
@@ -5,6 +5,7 @@
*
* Currently supported OHCI host devices:
* - Philips PNX4008
+ * - NXP LPC32xx
*
* Authors: Dmitry Chigirev <source@xxxxxxxxxx>
* Vitaly Wool <vitalywool@xxxxxxxxx>
@@ -25,20 +26,24 @@
#include <linux/i2c.h>
#include <mach/hardware.h>
+#include <asm/mach-types.h>
#include <asm/io.h>
#include <mach/platform.h>
#include <mach/irqs.h>
#include <asm/gpio.h>
-#define USB_CTRL IO_ADDRESS(PNX4008_PWRMAN_BASE + 0x64)
+#define USB_CONFIG_BASE 0x31020000
+#define PWRMAN_BASE 0x40004000
+
+#define USB_CTRL IO_ADDRESS(PWRMAN_BASE + 0x64)
/* USB_CTRL bit defines */
#define USB_SLAVE_HCLK_EN (1 << 24)
#define USB_HOST_NEED_CLK_EN (1 << 21)
-#define USB_OTG_CLK_CTRL IO_ADDRESS(PNX4008_USB_CONFIG_BASE + 0xFF4)
-#define USB_OTG_CLK_STAT IO_ADDRESS(PNX4008_USB_CONFIG_BASE + 0xFF8)
+#define USB_OTG_CLK_CTRL IO_ADDRESS(USB_CONFIG_BASE + 0xFF4)
+#define USB_OTG_CLK_STAT IO_ADDRESS(USB_CONFIG_BASE + 0xFF8)
/* USB_OTG_CLK_CTRL bit defines */
#define AHB_M_CLOCK_ON (1 << 4)
@@ -47,7 +52,7 @@
#define DEV_CLOCK_ON (1 << 1)
#define HOST_CLOCK_ON (1 << 0)
-#define USB_OTG_STAT_CONTROL IO_ADDRESS(PNX4008_USB_CONFIG_BASE + 0x110)
+#define USB_OTG_STAT_CONTROL IO_ADDRESS(USB_CONFIG_BASE + 0x110)
/* USB_OTG_STAT_CONTROL bit defines */
#define TRANSPARENT_I2C_EN (1 << 7)
@@ -101,6 +106,15 @@
#define ISP1301_I2C_INTERRUPT_RISING 0xE
#define ISP1301_I2C_REG_CLEAR_ADDR 1
+/* On LPC32xx, those are undefined */
+#ifndef start_int_set_falling_edge
+#define start_int_set_falling_edge(irq)
+#define start_int_set_rising_edge(irq)
+#define start_int_ack(irq)
+#define start_int_mask(irq)
+#define start_int_umask(irq)
+#endif
+
static struct i2c_driver isp1301_driver;
static struct i2c_client *isp1301_i2c_client;
@@ -146,7 +160,7 @@ static void i2c_write(u8 buf, u8 subaddr
i2c_master_send(isp1301_i2c_client, &tmpbuf[0], 2);
}
-static void isp1301_configure(void)
+static void isp1301_configure_pnx4008(void)
{
/* PNX4008 only supports DAT_SE0 USB mode */
/* PNX4008 R2A requires setting the MAX603 to output 3.6V */
@@ -169,7 +183,53 @@ static void isp1301_configure(void)
ISP1301_I2C_INTERRUPT_FALLING | ISP1301_I2C_REG_CLEAR_ADDR);
i2c_write(0xFF,
ISP1301_I2C_INTERRUPT_RISING | ISP1301_I2C_REG_CLEAR_ADDR);
+}
+
+static void isp1301_configure_lpc32xx(void)
+{
+ /* LPC32XX only supports DAT_SE0 USB mode */
+ /* This sequence is important */
+
+ /* Disable transparent UART mode first */
+ i2c_write(MC1_UART_EN,
+ (ISP1301_I2C_MODE_CONTROL_1 | ISP1301_I2C_REG_CLEAR_ADDR));
+ i2c_write(~MC1_SPEED_REG, (ISP1301_I2C_MODE_CONTROL_1 |
+ ISP1301_I2C_REG_CLEAR_ADDR));
+ i2c_write(MC1_SPEED_REG, ISP1301_I2C_MODE_CONTROL_1);
+ i2c_write(~0,
+ (ISP1301_I2C_MODE_CONTROL_2 | ISP1301_I2C_REG_CLEAR_ADDR));
+ i2c_write((MC2_BI_DI | MC2_PSW_EN | MC2_SPD_SUSP_CTRL),
+ ISP1301_I2C_MODE_CONTROL_2);
+ i2c_write(~0, (ISP1301_I2C_OTG_CONTROL_1 | ISP1301_I2C_REG_CLEAR_ADDR));
+ i2c_write(MC1_DAT_SE0, ISP1301_I2C_MODE_CONTROL_1);
+ i2c_write((OTG1_DM_PULLDOWN | OTG1_DP_PULLDOWN),
+ ISP1301_I2C_OTG_CONTROL_1);
+ i2c_write((OTG1_DM_PULLUP | OTG1_DP_PULLUP),
+ (ISP1301_I2C_OTG_CONTROL_1 | ISP1301_I2C_REG_CLEAR_ADDR));
+ i2c_write(~0,
+ ISP1301_I2C_INTERRUPT_LATCH | ISP1301_I2C_REG_CLEAR_ADDR);
+ i2c_write(~0,
+ ISP1301_I2C_INTERRUPT_FALLING | ISP1301_I2C_REG_CLEAR_ADDR);
+ i2c_write(~0,
+ ISP1301_I2C_INTERRUPT_RISING | ISP1301_I2C_REG_CLEAR_ADDR);
+
+ /* Enable usb_need_clk clock after transceiver is initialized */
+ __raw_writel((__raw_readl(USB_CTRL) | (1 << 22)), USB_CTRL);
+
+ printk(KERN_INFO "ISP1301 Vendor ID : 0x%04x\n",
+ i2c_smbus_read_word_data(isp1301_i2c_client, 0x00));
+ printk(KERN_INFO "ISP1301 Product ID : 0x%04x\n",
+ i2c_smbus_read_word_data(isp1301_i2c_client, 0x02));
+ printk(KERN_INFO "ISP1301 Version ID : 0x%04x\n",
+ i2c_smbus_read_word_data(isp1301_i2c_client, 0x14));
+}
+static void isp1301_configure(void)
+{
+ if (machine_is_pnx4008())
+ isp1301_configure_pnx4008();
+ else
+ isp1301_configure_lpc32xx();
}
static inline void isp1301_vbus_on(void)
@@ -260,39 +320,43 @@ static const struct hc_driver ohci_nxp_h
static void nxp_set_usb_bits(void)
{
- start_int_set_falling_edge(SE_USB_OTG_ATX_INT_N);
- start_int_ack(SE_USB_OTG_ATX_INT_N);
- start_int_umask(SE_USB_OTG_ATX_INT_N);
-
- start_int_set_rising_edge(SE_USB_OTG_TIMER_INT);
- start_int_ack(SE_USB_OTG_TIMER_INT);
- start_int_umask(SE_USB_OTG_TIMER_INT);
-
- start_int_set_rising_edge(SE_USB_I2C_INT);
- start_int_ack(SE_USB_I2C_INT);
- start_int_umask(SE_USB_I2C_INT);
-
- start_int_set_rising_edge(SE_USB_INT);
- start_int_ack(SE_USB_INT);
- start_int_umask(SE_USB_INT);
-
- start_int_set_rising_edge(SE_USB_NEED_CLK_INT);
- start_int_ack(SE_USB_NEED_CLK_INT);
- start_int_umask(SE_USB_NEED_CLK_INT);
-
- start_int_set_rising_edge(SE_USB_AHB_NEED_CLK_INT);
- start_int_ack(SE_USB_AHB_NEED_CLK_INT);
- start_int_umask(SE_USB_AHB_NEED_CLK_INT);
+ if (machine_is_pnx4008()) {
+ start_int_set_falling_edge(SE_USB_OTG_ATX_INT_N);
+ start_int_ack(SE_USB_OTG_ATX_INT_N);
+ start_int_umask(SE_USB_OTG_ATX_INT_N);
+
+ start_int_set_rising_edge(SE_USB_OTG_TIMER_INT);
+ start_int_ack(SE_USB_OTG_TIMER_INT);
+ start_int_umask(SE_USB_OTG_TIMER_INT);
+
+ start_int_set_rising_edge(SE_USB_I2C_INT);
+ start_int_ack(SE_USB_I2C_INT);
+ start_int_umask(SE_USB_I2C_INT);
+
+ start_int_set_rising_edge(SE_USB_INT);
+ start_int_ack(SE_USB_INT);
+ start_int_umask(SE_USB_INT);
+
+ start_int_set_rising_edge(SE_USB_NEED_CLK_INT);
+ start_int_ack(SE_USB_NEED_CLK_INT);
+ start_int_umask(SE_USB_NEED_CLK_INT);
+
+ start_int_set_rising_edge(SE_USB_AHB_NEED_CLK_INT);
+ start_int_ack(SE_USB_AHB_NEED_CLK_INT);
+ start_int_umask(SE_USB_AHB_NEED_CLK_INT);
+ }
}
static void nxp_unset_usb_bits(void)
{
- start_int_mask(SE_USB_OTG_ATX_INT_N);
- start_int_mask(SE_USB_OTG_TIMER_INT);
- start_int_mask(SE_USB_I2C_INT);
- start_int_mask(SE_USB_INT);
- start_int_mask(SE_USB_NEED_CLK_INT);
- start_int_mask(SE_USB_AHB_NEED_CLK_INT);
+ if (machine_is_pnx4008()) {
+ start_int_mask(SE_USB_OTG_ATX_INT_N);
+ start_int_mask(SE_USB_OTG_TIMER_INT);
+ start_int_mask(SE_USB_I2C_INT);
+ start_int_mask(SE_USB_INT);
+ start_int_mask(SE_USB_NEED_CLK_INT);
+ start_int_mask(SE_USB_AHB_NEED_CLK_INT);
+ }
}
static int __devinit usb_hcd_nxp_probe(struct platform_device *pdev)
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/