Re: [RFC v2 1/2] PCI-Express Non-Transparent Bridge Support

[Jon Mason]

On Mon, Jul 30, 2012 at 10:50:13AM -0600, Bjorn Helgaas wrote:
> On Sun, Jul 29, 2012 at 6:26 PM, Jon Mason <jon.mason@xxxxxxxxx> wrote:
> > A PCI-Express non-transparent bridge (NTB) is a point-to-point PCIe bus
> > connecting 2 systems, providing electrical isolation between the two subsystems.
> > A non-transparent bridge is functionally similar to a transparent bridge except
> > that both sides of the bridge have their own independent address domains.  The
> > host on one side of the bridge will not have the visibility of the complete
> > memory or I/O space on the other side of the bridge.  To communicate across the
> > non-transparent bridge, each NTB endpoint has one (or more) apertures exposed to
> > the local system.  Writes to these apertures are mirrored to memory on the
> > remote system.  Communications can also occur through the use of doorbell
> > registers that initiate interrupts to the alternate domain, and scratch-pad
> > registers accessible from both sides.
> >
> > The NTB device driver is needed to configure these memory windows, doorbell, and
> > scratch-pad registers as well as use them in such a way as they can be turned
> > into a viable communication channel to the remote system.  ntb_hw.[ch]
> > determines the usage model (NTB to NTB or NTB to Root Port) and abstracts away
> > the underlying hardware to provide access and a common interface to the doorbell
> > registers, scratch pads, and memory windows.  These hardware interfaces are
> > exported so that other, non-mainlined kernel drivers can access these.
> > ntb_transport.[ch] also uses the exported interfaces in ntb_hw.[ch] to setup a
> > communication channel(s) and provide a reliable way of transferring data from
> > one side to the other, which it then exports so that "client" drivers can access
> > them.  These client drivers are used to provide a standard kernel interface
> > (i.e., Ethernet device) to NTB, such that Linux can transfer data from one
> > system to the other in a standard way.
> >
> > Signed-off-by: Jon Mason <jon.mason@xxxxxxxxx>
> > ---
> >  MAINTAINERS                 |    6 +
> >  drivers/Kconfig             |    2 +
> >  drivers/Makefile            |    1 +
> >  drivers/ntb/Kconfig         |   13 +
> >  drivers/ntb/Makefile        |    3 +
> >  drivers/ntb/ntb_hw.c        | 1178 ++++++++++++++++++++++++++++++++++++
> >  drivers/ntb/ntb_hw.h        |  206 +++++++
> >  drivers/ntb/ntb_regs.h      |  150 +++++
> >  drivers/ntb/ntb_transport.c | 1387 +++++++++++++++++++++++++++++++++++++++++++
> >  include/linux/ntb.h         |   92 +++
> 
> Where will drivers for non-Intel NTBs fit in this hierarchy?  It seems
> a bit presumptuous to claim the generic "ntb" names just for Intel
> devices.

I've tried to make it all generic enough that non-Intel NTBs should plug in with
minimal changes to ntb_hw.c.  If their design is too divergent, then a slight
redesign of ntb_hw.c might be necessary.  But from what I've seen of other
designs on the internet, they appear to be extremely similar.  The transport and
client drivers were written with the hardware abstracted away as much as
possible to prevent the need to modify it for different hardware.  If there is
anything which is Intel hardware specific, I'd be happy to change it to make it
more generic.

Thanks,
Jon
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/