Re: [PATCH 7/8] ARM: ux500: Use the GPIO regulator framework forSDI0's 'en' and 'vsel'

From: Ulf Hansson
Date: Thu Dec 13 2012 - 10:09:38 EST

On 13 December 2012 14:22, Lee Jones <lee.jones@xxxxxxxxxx> wrote:
> To prevent lots of unnecessary call-backs into platform code, we're
> now using the GPIO regulator framework to control the 'enable' (en)
> and 'voltage select' (vsel) GPIO pins which in turn control the
> MMCI's secondary regulator settings. This already works with Device
> Tree, but when booting with ATAGs we need to register it as a
> platform device.
>
> Signed-off-by: Lee Jones <lee.jones@xxxxxxxxxx>
> ---
> arch/arm/mach-ux500/board-mop500-regulators.c | 14 ++++++++
> arch/arm/mach-ux500/board-mop500-regulators.h | 1 +
> arch/arm/mach-ux500/board-mop500.c | 44 +++++++++++++++++++++++++
> 3 files changed, 59 insertions(+)
>
> diff --git a/arch/arm/mach-ux500/board-mop500-regulators.c b/arch/arm/mach-ux500/board-mop500-regulators.c
> index 2a17bc5..cb75405 100644
> --- a/arch/arm/mach-ux500/board-mop500-regulators.c
> +++ b/arch/arm/mach-ux500/board-mop500-regulators.c
> @@ -28,6 +28,20 @@ struct regulator_init_data gpio_en_3v3_regulator = {
> .consumer_supplies = gpio_en_3v3_consumers,
> };
>
> +static struct regulator_consumer_supply sdi0_reg_consumers[] = {
> + REGULATOR_SUPPLY("vqmmc", "sdi0"),
> +};
> +
> +struct regulator_init_data sdi0_reg_init_data = {
> + .constraints = {
> + .min_uV = 1800000,
> + .max_uV = 2900000,
> + .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE|REGULATOR_CHANGE_STATUS,
> + },
> + .num_consumer_supplies = ARRAY_SIZE(sdi0_reg_consumers),
> + .consumer_supplies = sdi0_reg_consumers,
> +};
> +
> /*
> * TPS61052 regulator
> */
> diff --git a/arch/arm/mach-ux500/board-mop500-regulators.h b/arch/arm/mach-ux500/board-mop500-regulators.h
> index 78a0642..0c79d90 100644
> --- a/arch/arm/mach-ux500/board-mop500-regulators.h
> +++ b/arch/arm/mach-ux500/board-mop500-regulators.h
> @@ -19,5 +19,6 @@ ab8500_regulator_reg_init[AB8500_NUM_REGULATOR_REGISTERS];
> extern struct regulator_init_data ab8500_regulators[AB8500_NUM_REGULATORS];
> extern struct regulator_init_data tps61052_regulator;
> extern struct regulator_init_data gpio_en_3v3_regulator;
> +extern struct regulator_init_data sdi0_reg_init_data;
>
> #endif
> diff --git a/arch/arm/mach-ux500/board-mop500.c b/arch/arm/mach-ux500/board-mop500.c
> index daa4237..e934176 100644
> --- a/arch/arm/mach-ux500/board-mop500.c
> +++ b/arch/arm/mach-ux500/board-mop500.c
> @@ -24,6 +24,8 @@
> #include <linux/mfd/abx500/ab8500.h>
> #include <linux/regulator/ab8500.h>
> #include <linux/regulator/fixed.h>
> +#include <linux/regulator/driver.h>
> +#include <linux/regulator/gpio-regulator.h>
> #include <linux/mfd/tc3589x.h>
> #include <linux/mfd/tps6105x.h>
> #include <linux/mfd/abx500/ab8500-gpio.h>
> @@ -91,6 +93,37 @@ static struct platform_device snowball_gpio_en_3v3_regulator_dev = {
> },
> };
>
> +/* Dynamically populated. */
> +static struct gpio sdi0_reg_gpios[] = {
> + { 0, GPIOF_OUT_INIT_LOW, "mmci_vsel" },
> +};
> +
> +static struct gpio_regulator_state sdi0_reg_states[] = {
> + { .value = 2900000, .gpios = (0 << 0) },
> + { .value = 1800000, .gpios = (1 << 0) },
> +};
> +
> +static struct gpio_regulator_config sdi0_reg_info = {
> + .supply_name = "ext-mmc-level-shifter",
> + .gpios = sdi0_reg_gpios,
> + .nr_gpios = ARRAY_SIZE(sdi0_reg_gpios),
> + .states = sdi0_reg_states,
> + .nr_states = ARRAY_SIZE(sdi0_reg_states),
> + .type = REGULATOR_VOLTAGE,
> + .enable_high = 1,
> + .enabled_at_boot = 0,
> + .init_data = &sdi0_reg_init_data,
> + .startup_delay = 100,
> +};
> +
> +static struct platform_device sdi0_regulator = {
> + .name = "gpio-regulator",
> + .id = -1,
> + .dev = {
> + .platform_data = &sdi0_reg_info,
> + },
> +};
> +
> static struct ab8500_gpio_platform_data ab8500_gpio_pdata = {
> .gpio_base = MOP500_AB8500_PIN_GPIO(1),
> .irq_base = MOP500_AB8500_VIR_GPIO_IRQ_BASE,
> @@ -440,6 +473,7 @@ static struct hash_platform_data u8500_hash1_platform_data = {
> /* add any platform devices here - TODO */
> static struct platform_device *mop500_platform_devs[] __initdata = {
> &mop500_gpio_keys_device,
> + &sdi0_regulator,
> };
>
> #ifdef CONFIG_STE_DMA40
> @@ -581,6 +615,7 @@ static struct platform_device *snowball_platform_devs[] __initdata = {
> &snowball_key_dev,
> &snowball_sbnet_dev,
> &snowball_gpio_en_3v3_regulator_dev,
> + &sdi0_regulator,
> };
>
> static void __init mop500_init_machine(void)
> @@ -591,6 +626,9 @@ static void __init mop500_init_machine(void)
>
> mop500_gpio_keys[0].gpio = GPIO_PROX_SENSOR;
>
> + sdi0_reg_info.enable_gpio = GPIO_SDMMC_EN;
> + sdi0_reg_info.gpios[0].gpio = GPIO_SDMMC_1V8_3V_SEL;
> +
> mop500_pinmaps_init();
> parent = u8500_init_devices(&ab8500_platdata);
>
> @@ -623,6 +661,9 @@ static void __init snowball_init_machine(void)
> struct device *parent = NULL;
> int i;
>
> + sdi0_reg_info.enable_gpio = SNOWBALL_SDMMC_EN_GPIO;
> + sdi0_reg_info.gpios[0].gpio = SNOWBALL_SDMMC_1V8_3V_GPIO;
> +
> snowball_pinmaps_init();
> parent = u8500_init_devices(&ab8500_platdata);
>
> @@ -655,6 +696,9 @@ static void __init hrefv60_init_machine(void)
> */
> mop500_gpio_keys[0].gpio = HREFV60_PROX_SENSE_GPIO;
>
> + sdi0_reg_info.enable_gpio = HREFV60_SDMMC_EN_GPIO;
> + sdi0_reg_info.gpios[0].gpio = HREFV60_SDMMC_1V8_3V_GPIO;
> +
> hrefv60_pinmaps_init();
> parent = u8500_init_devices(&ab8500_platdata);
>
> --
> 1.7.9.5
>


Acked-by: Ulf Hansson <ulf.hansson@xxxxxxxxxx>
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/