Re: [PATCH 4/4] drivers: usb: start using the control module driver
From: kishon
Date: Fri Jan 18 2013 - 07:11:31 EST
On Friday 18 January 2013 05:32 PM, Felipe Balbi wrote:
Hi,
On Fri, Jan 18, 2013 at 03:10:45PM +0530, Kishon Vijay Abraham I wrote:
Start using the control module driver for powering on the PHY and for
writing to the mailbox instead of writing to the control module
registers on their own.
Signed-off-by: Kishon Vijay Abraham I <kishon@xxxxxx>
---
Documentation/devicetree/bindings/usb/omap-usb.txt | 4 ++
Documentation/devicetree/bindings/usb/usb-phy.txt | 7 +--
arch/arm/mach-omap2/omap_hwmod_44xx_data.c | 13 ----
drivers/usb/musb/Kconfig | 1 +
drivers/usb/musb/omap2430.c | 64 ++++++++------------
drivers/usb/musb/omap2430.h | 9 ---
drivers/usb/phy/Kconfig | 1 +
drivers/usb/phy/omap-usb2.c | 38 +++---------
include/linux/usb/omap_usb.h | 4 +-
9 files changed, 42 insertions(+), 99 deletions(-)
diff --git a/Documentation/devicetree/bindings/usb/omap-usb.txt b/Documentation/devicetree/bindings/usb/omap-usb.txt
index ead6ba9..8bedbba 100644
--- a/Documentation/devicetree/bindings/usb/omap-usb.txt
+++ b/Documentation/devicetree/bindings/usb/omap-usb.txt
@@ -3,6 +3,9 @@ OMAP GLUE AND OTHER OMAP SPECIFIC COMPONENTS
OMAP MUSB GLUE
- compatible : Should be "ti,omap4-musb" or "ti,omap3-musb"
- ti,hwmods : must be "usb_otg_hs"
+ - ti,has_mailbox : to specify that omap uses an external mailbox
+ (in control module) to communicate with the musb core during device connect
+ and disconnect.
- multipoint : Should be "1" indicating the musb controller supports
multipoint. This is a MUSB configuration-specific setting.
- num_eps : Specifies the number of endpoints. This is also a
@@ -24,6 +27,7 @@ SOC specific device node entry
usb_otg_hs: usb_otg_hs@4a0ab000 {
compatible = "ti,omap4-musb";
ti,hwmods = "usb_otg_hs";
+ ti,has_mailbox;
multipoint = <1>;
num_eps = <16>;
ram_bits = <12>;
diff --git a/Documentation/devicetree/bindings/usb/usb-phy.txt b/Documentation/devicetree/bindings/usb/usb-phy.txt
index 2466b6f..48761a2 100644
--- a/Documentation/devicetree/bindings/usb/usb-phy.txt
+++ b/Documentation/devicetree/bindings/usb/usb-phy.txt
@@ -4,9 +4,7 @@ OMAP USB2 PHY
Required properties:
- compatible: Should be "ti,omap-usb2"
- - reg : Address and length of the register set for the device. Also
-add the address of control module dev conf register until a driver for
-control module is added
+ - reg : Address and length of the register set for the device.
Optional properties:
- ctrl_module : phandle of the control module used by PHY driver to power on
@@ -16,7 +14,6 @@ This is usually a subnode of ocp2scp to which it is connected.
usb2phy@4a0ad080 {
compatible = "ti,omap-usb2";
- reg = <0x4a0ad080 0x58>,
- <0x4a002300 0x4>;
+ reg = <0x4a0ad080 0x58>;
ctrl_module = <&omap_control_usb>;
};
diff --git a/arch/arm/mach-omap2/omap_hwmod_44xx_data.c b/arch/arm/mach-omap2/omap_hwmod_44xx_data.c
index 129d508..103f4ba 100644
--- a/arch/arm/mach-omap2/omap_hwmod_44xx_data.c
+++ b/arch/arm/mach-omap2/omap_hwmod_44xx_data.c
@@ -2698,13 +2698,6 @@ static struct resource omap44xx_usb_phy_and_pll_addrs[] = {
.end = 0x4a0ae000,
.flags = IORESOURCE_MEM,
},
- {
- /* XXX: Remove this once control module driver is in place */
- .name = "ctrl_dev",
- .start = 0x4a002300,
- .end = 0x4a002303,
- .flags = IORESOURCE_MEM,
- },
{ }
};
@@ -6152,12 +6145,6 @@ static struct omap_hwmod_addr_space omap44xx_usb_otg_hs_addrs[] = {
.pa_end = 0x4a0ab7ff,
.flags = ADDR_TYPE_RT
},
- {
- /* XXX: Remove this once control module driver is in place */
- .pa_start = 0x4a00233c,
- .pa_end = 0x4a00233f,
- .flags = ADDR_TYPE_RT
- },
{ }
};
diff --git a/drivers/usb/musb/Kconfig b/drivers/usb/musb/Kconfig
index 23a0b7f..de6e5ce 100644
--- a/drivers/usb/musb/Kconfig
+++ b/drivers/usb/musb/Kconfig
@@ -11,6 +11,7 @@ config USB_MUSB_HDRC
select NOP_USB_XCEIV if (SOC_TI81XX || SOC_AM33XX)
select TWL4030_USB if MACH_OMAP_3430SDP
select TWL6030_USB if MACH_OMAP_4430SDP || MACH_OMAP4_PANDA
+ select OMAP_CONTROL_USB if MACH_OMAP_4430SDP || MACH_OMAP4_PANDA
select USB_OTG_UTILS
help
Say Y here if your system has a dual role high speed USB
diff --git a/drivers/usb/musb/omap2430.c b/drivers/usb/musb/omap2430.c
index da00af4..3e7ceef 100644
--- a/drivers/usb/musb/omap2430.c
+++ b/drivers/usb/musb/omap2430.c
@@ -37,6 +37,7 @@
#include <linux/err.h>
#include <linux/delay.h>
#include <linux/usb/musb-omap.h>
+#include <linux/usb/omap_control_usb.h>
#include "musb_core.h"
#include "omap2430.h"
@@ -46,7 +47,7 @@ struct omap2430_glue {
struct platform_device *musb;
enum omap_musb_vbus_id_status status;
struct work_struct omap_musb_mailbox_work;
- u32 __iomem *control_otghs;
+ struct device *control_otghs;
};
#define glue_to_musb(g) platform_get_drvdata(g->musb)
@@ -54,26 +55,6 @@ struct omap2430_glue *_glue;
static struct timer_list musb_idle_timer;
-/**
- * omap4_usb_phy_mailbox - write to usb otg mailbox
- * @glue: struct omap2430_glue *
- * @val: the value to be written to the mailbox
- *
- * On detection of a device (ID pin is grounded), this API should be called
- * to set AVALID, VBUSVALID and ID pin is grounded.
- *
- * When OMAP is connected to a host (OMAP in device mode), this API
- * is called to set AVALID, VBUSVALID and ID pin in high impedance.
- *
- * XXX: This function will be removed once we have a seperate driver for
- * control module
- */
-static void omap4_usb_phy_mailbox(struct omap2430_glue *glue, u32 val)
-{
- if (glue->control_otghs)
- writel(val, glue->control_otghs);
-}
-
static void musb_do_idle(unsigned long _musb)
{
struct musb *musb = (void *)_musb;
@@ -269,7 +250,6 @@ EXPORT_SYMBOL_GPL(omap_musb_mailbox);
static void omap_musb_set_mailbox(struct omap2430_glue *glue)
{
- u32 val;
struct musb *musb = glue_to_musb(glue);
struct device *dev = musb->controller;
struct musb_hdrc_platform_data *pdata = dev->platform_data;
@@ -285,8 +265,8 @@ static void omap_musb_set_mailbox(struct omap2430_glue *glue)
musb->xceiv->last_event = USB_EVENT_ID;
if (musb->gadget_driver) {
pm_runtime_get_sync(dev);
- val = AVALID | VBUSVALID;
- omap4_usb_phy_mailbox(glue, val);
+ if (!IS_ERR(glue->control_otghs))
+ omap_control_usb_host_mode(glue->control_otghs);
you could introduce a helper to do the checks for you. something like:
static inline void omap_control_set_mode(*ctrl, int mode)
{
if (IS_ERR(glue->control_otghs))
return;
switch (mode) {
case HOST:
omap_control_usb_host_mode(ctrl);
break;
case DEVICE:
omap_control_usb_device(ctrl)
break;
default:
meh();
}
}
likewise for power() method
Ok.
Thanks
Kishon
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/