Re: [PATCH V2] rtc: rtc-v3020: use gpio_request_array()

[Igor Grinberg]

On 02/22/13 04:19, Jingoo Han wrote:
> Using gpio_request_array()/gpio_free_array() can make the code
> simpler because it can set the direction and initial value
> in one shot and the for loop is unnecessary.
> 
> Also, struct v3020_gpio is removed, because the struct v3020_gpio
> is replaced with struct gpio.
> 
> Signed-off-by: Jingoo Han <jg1.han@xxxxxxxxxxx>
> ---
> Changes since v1:
> - Replace gpio_request_one() with gpio_request_array()

Thanks for addressing this!
It looks much better now, although one comment below.

> 
>  drivers/rtc/rtc-v3020.c |   37 ++++++++++++-------------------------
>  1 files changed, 12 insertions(+), 25 deletions(-)
> 
> diff --git a/drivers/rtc/rtc-v3020.c b/drivers/rtc/rtc-v3020.c
> index bca5d67..600798c 100644
> --- a/drivers/rtc/rtc-v3020.c
> +++ b/drivers/rtc/rtc-v3020.c

[...]

> @@ -107,48 +102,40 @@ static struct v3020_chip_ops v3020_mmio_ops = {
>  	.write_bit	= v3020_mmio_write_bit,
>  };
>  
> -static struct v3020_gpio v3020_gpio[] = {
> -	{ "RTC CS", 0 },
> -	{ "RTC WR", 0 },
> -	{ "RTC RD", 0 },
> -	{ "RTC IO", 0 },
> +static struct gpio v3020_gpio[] = {
> +	{ 0, GPIOF_OUT_INIT_HIGH, "RTC CS"},
> +	{ 0, GPIOF_OUT_INIT_HIGH, "RTC WR"},
> +	{ 0, GPIOF_OUT_INIT_HIGH, "RTC RD"},
> +	{ 0, GPIOF_OUT_INIT_HIGH, "RTC IO"},
>  };
>  
>  static int v3020_gpio_map(struct v3020 *chip, struct platform_device *pdev,
>  			  struct v3020_platform_data *pdata)
>  {
> -	int i, err;
> +	int err;
>  
>  	v3020_gpio[V3020_CS].gpio = pdata->gpio_cs;
>  	v3020_gpio[V3020_WR].gpio = pdata->gpio_wr;
>  	v3020_gpio[V3020_RD].gpio = pdata->gpio_rd;
>  	v3020_gpio[V3020_IO].gpio = pdata->gpio_io;
>  
> -	for (i = 0; i < ARRAY_SIZE(v3020_gpio); i++) {
> -		err = gpio_request(v3020_gpio[i].gpio, v3020_gpio[i].name);
> -		if (err)
> -			goto err_request;
> -
> -		gpio_direction_output(v3020_gpio[i].gpio, 1);
> -	}
> +	err = gpio_request_array(v3020_gpio, ARRAY_SIZE(v3020_gpio));
> +	if (err)
> +		goto err_request;
>  
>  	chip->gpio = v3020_gpio;
>  
>  	return 0;
>  
>  err_request:
> -	while (--i >= 0)
> -		gpio_free(v3020_gpio[i].gpio);
> +	gpio_free_array(v3020_gpio, ARRAY_SIZE(v3020_gpio));

Once you use the gpio_request_array(), you don't need to care
about the error.
If gpio_request_array() fails, it does the roll back for you.
So, you just need to return err and remove the whole err_request label.

>  
>  	return err;
>  }
>  
>  static void v3020_gpio_unmap(struct v3020 *chip)
>  {
> -	int i;
> -
> -	for (i = 0; i < ARRAY_SIZE(v3020_gpio); i++)
> -		gpio_free(v3020_gpio[i].gpio);
> +	gpio_free_array(v3020_gpio, ARRAY_SIZE(v3020_gpio));
>  }
>  
>  static void v3020_gpio_write_bit(struct v3020 *chip, unsigned char bit)
> 

-- 
Regards,
Igor.
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/