[PATCH 07/24] ARM: OMAP: AM3517crane: Adapt to ehci-omap changes

[Roger Quadros]

Add platform device for 'nop-usb-xceiv'. This will be used as a
PHY for HS USB Port 1, so provide binding information for it.

Model RESET and Power for HS USB Port 1 as GPIO fixed regulators
and link them to the 'nop-usb-xceiv' PHY.

Signed-off-by: Roger Quadros <rogerq@xxxxxx>
Acked-by: Felipe Balbi <balbi@xxxxxx>
---
 arch/arm/mach-omap2/board-am3517crane.c |   95 +++++++++++++++++++++++++++----
 1 files changed, 83 insertions(+), 12 deletions(-)

diff --git a/arch/arm/mach-omap2/board-am3517crane.c b/arch/arm/mach-omap2/board-am3517crane.c
index 7d3358b..6dd6c1d 100644
--- a/arch/arm/mach-omap2/board-am3517crane.c
+++ b/arch/arm/mach-omap2/board-am3517crane.c
@@ -24,6 +24,9 @@
 #include <linux/mtd/mtd.h>
 #include <linux/mtd/nand.h>
 #include <linux/mtd/partitions.h>
+#include <linux/regulator/machine.h>
+#include <linux/regulator/fixed.h>
+#include <linux/usb/phy.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
@@ -47,15 +50,84 @@ static struct omap_board_mux board_mux[] __initdata = {
 };
 #endif
 
+/* PHY device on HS USB Port 1 i.e. nop_usb_xceiv.1 */
+static struct platform_device hsusb1_phy_device = {
+	.name = "nop_usb_xceiv",
+	.id = 1,
+};
+
+/* Regulator for HS USB Port 1 PHY reset */
+static struct regulator_consumer_supply hsusb1_reset_supplies[] = {
+	/* Link PHY device to reset supply so it gets used in the PHY driver */
+	REGULATOR_SUPPLY("reset", "nop_usb_xceiv.1"),
+};
+
+static struct regulator_init_data hsusb1_reset_data = {
+	.constraints = {
+		.valid_ops_mask = REGULATOR_CHANGE_STATUS,
+	},
+	.consumer_supplies = hsusb1_reset_supplies,
+	.num_consumer_supplies = ARRAY_SIZE(hsusb1_reset_supplies),
+};
+
+static struct fixed_voltage_config hsusb1_reset_config = {
+	.supply_name = "hsusb1_reset",
+	.microvolts = 3300000,
+	.gpio = GPIO_USB_NRESET,
+	.startup_delay = 70000, /* 70msec */
+	.enable_high = 1,
+	.enabled_at_boot = 0,   /* keep in RESET */
+	.init_data = &hsusb1_reset_data,
+};
+
+static struct platform_device hsusb1_reset_device = {
+	.name = "reg-fixed-voltage",
+	.id = PLATFORM_DEVID_AUTO,
+	.dev = {
+		.platform_data = &hsusb1_reset_config,
+	},
+};
+
+/* Regulator for HS USB Port 1 supply */
+static struct regulator_consumer_supply hsusb1_power_supplies[] = {
+/* Link PHY device to power supply so it gets enabled in the PHY driver */
+	REGULATOR_SUPPLY("vcc", "nop_usb_xceiv.1"),
+};
+
+static struct regulator_init_data hsusb1_power_data = {
+	.constraints = {
+		.valid_ops_mask = REGULATOR_CHANGE_STATUS,
+	},
+	.consumer_supplies = hsusb1_power_supplies,
+	.num_consumer_supplies  = ARRAY_SIZE(hsusb1_power_supplies),
+};
+
+static struct fixed_voltage_config hsusb1_power_config = {
+	.supply_name = "hsusb1_vbus",
+	.microvolts = 5000000,
+	.gpio = GPIO_USB_POWER,
+	.startup_delay = 70000, /* 70msec */
+	.enable_high = 1,
+	.enabled_at_boot = 0,
+	.init_data = &hsusb1_power_data,
+};
+
+static struct platform_device hsusb1_power_device = {
+	.name = "reg-fixed-voltage",
+	.id = PLATFORM_DEVID_AUTO,
+	.dev = {
+		.platform_data = &hsusb1_power_config,
+	},
+};
+
 static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
 	.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
-	.port_mode[1] = OMAP_USBHS_PORT_MODE_UNUSED,
-	.port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
+};
 
-	.phy_reset  = true,
-	.reset_gpio_port[0]  = GPIO_USB_NRESET,
-	.reset_gpio_port[1]  = -EINVAL,
-	.reset_gpio_port[2]  = -EINVAL
+static struct platform_device *am3517_crane_devices[] __initdata = {
+	&hsusb1_phy_device,
+	&hsusb1_reset_device,
+	&hsusb1_power_device,
 };
 
 static struct mtd_partition crane_nand_partitions[] = {
@@ -131,12 +203,11 @@ static void __init am3517_crane_init(void)
 		return;
 	}
 
-	ret = gpio_request_one(GPIO_USB_POWER, GPIOF_OUT_INIT_HIGH,
-			       "usb_ehci_enable");
-	if (ret < 0) {
-		pr_err("Can not request GPIO %d\n", GPIO_USB_POWER);
-		return;
-	}
+	platform_add_devices(am3517_crane_devices,
+				ARRAY_SIZE(am3517_crane_devices));
+
+	/* PHY on HSUSB Port 1 i.e. index 0 */
+	usb_bind_phy("ehci-omap.0", 0, "nop_usb_xceiv.1");
 
 	usbhs_init(&usbhs_bdata);
 	am35xx_emac_init(AM35XX_DEFAULT_MDIO_FREQUENCY, 1);
-- 
1.7.4.1

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/