[PATCH 2/6] dmaengine: ste_dma40: Replace ST-E's home-brew DMA direction defs with generic ones

[Lee Jones]

STEDMA40_*_TO_* direction definitions are identical in all but name to
the pre-defined generic DMA_*_TO_* ones. Let's make things easy by not
duplicating such things.

Cc: Vinod Koul <vinod.koul@xxxxxxxxx>
Cc: Dan Williams <djbw@xxxxxx>
Cc: Per Forlin <per.forlin@xxxxxxxxxxxxxx>
Cc: Rabin Vincent <rabin@xxxxxx>
Signed-off-by: Lee Jones <lee.jones@xxxxxxxxxx>
---
 drivers/dma/ste_dma40.c    |   36 ++++++++++++++++++------------------
 drivers/dma/ste_dma40_ll.c |   24 ++++++++++++------------
 2 files changed, 30 insertions(+), 30 deletions(-)

diff --git a/drivers/dma/ste_dma40.c b/drivers/dma/ste_dma40.c
index 78511ef..7239b90 100644
--- a/drivers/dma/ste_dma40.c
+++ b/drivers/dma/ste_dma40.c
@@ -58,9 +58,9 @@
 #define D40_ALLOC_PHY		BIT(30)
 #define D40_ALLOC_LOG_FREE	0
 
-#define D40_IS_SRC(dir)  (dir == STEDMA40_PERIPH_TO_MEM)
-#define D40_IS_DST(dir) ((dir == STEDMA40_MEM_TO_PERIPH) || \
-			 (dir == STEDMA40_MEM_TO_MEM))
+#define D40_IS_SRC(dir)  (dir == DMA_DEV_TO_MEM)
+#define D40_IS_DST(dir) ((dir == DMA_MEM_TO_DEV) || \
+			 (dir == DMA_MEM_TO_MEM))
 
 /* Reserved event lines for memcpy only. */
 static int dma40_memcpy_channels[] = { 56, 57, 58, 59, 60 };
@@ -68,7 +68,7 @@ static int dma40_memcpy_channels[] = { 56, 57, 58, 59, 60 };
 /* Default configuration for physcial memcpy */
 struct stedma40_chan_cfg dma40_memcpy_conf_phy = {
 	.mode = STEDMA40_MODE_PHYSICAL,
-	.dir = STEDMA40_MEM_TO_MEM,
+	.dir = DMA_MEM_TO_MEM,
 
 	.src_info.data_width = STEDMA40_BYTE_WIDTH,
 	.src_info.psize = STEDMA40_PSIZE_PHY_1,
@@ -82,7 +82,7 @@ struct stedma40_chan_cfg dma40_memcpy_conf_phy = {
 /* Default configuration for logical memcpy */
 struct stedma40_chan_cfg dma40_memcpy_conf_log = {
 	.mode = STEDMA40_MODE_LOGICAL,
-	.dir = STEDMA40_MEM_TO_MEM,
+	.dir = DMA_MEM_TO_MEM,
 
 	.src_info.data_width = STEDMA40_BYTE_WIDTH,
 	.src_info.psize = STEDMA40_PSIZE_LOG_1,
@@ -1302,7 +1302,7 @@ static void d40_config_set_event(struct d40_chan *d40c,
 
 	/* Enable event line connected to device (or memcpy) */
 	if (D40_IS_SRC(d40c->dma_cfg.dir) ||
-	    (d40c->dma_cfg.dir == STEDMA40_PERIPH_TO_PERIPH))
+	    (d40c->dma_cfg.dir == DMA_DEV_TO_DEV))
 		__d40_config_set_event(d40c, event_type, event,
 				       D40_CHAN_REG_SSLNK);
 
@@ -1764,7 +1764,7 @@ static int d40_validate_conf(struct d40_chan *d40c,
 		res = -EINVAL;
 	}
 
-	if (conf->dir == STEDMA40_PERIPH_TO_PERIPH) {
+	if (conf->dir == DMA_DEV_TO_DEV) {
 		/*
 		 * DMAC HW supports it. Will be added to this driver,
 		 * in case any dma client requires it.
@@ -1910,7 +1910,7 @@ static int d40_allocate_channel(struct d40_chan *d40c, bool *first_phy_user)
 	event_line = D40_TYPE_TO_EVENT(dev_type);
 
 	if (!is_log) {
-		if (dir == STEDMA40_MEM_TO_MEM) {
+		if (dir == DMA_MEM_TO_MEM) {
 			/* Find physical half channel */
 			if (d40c->dma_cfg.use_fixed_channel) {
 				i = d40c->dma_cfg.phy_channel;
@@ -2365,11 +2365,11 @@ static void d40_set_prio_realtime(struct d40_chan *d40c)
 		return;
 
 	if (D40_IS_SRC(d40c->dma_cfg.dir) ||
-	    (d40c->dma_cfg.dir == STEDMA40_PERIPH_TO_PERIPH))
+	    (d40c->dma_cfg.dir == DMA_DEV_TO_DEV))
 		__d40_set_prio_rt(d40c, d40c->dma_cfg.dev_type, true);
 
-	if ((d40c->dma_cfg.dir ==  STEDMA40_MEM_TO_PERIPH) ||
-	    (d40c->dma_cfg.dir == STEDMA40_PERIPH_TO_PERIPH))
+	if ((d40c->dma_cfg.dir ==  DMA_MEM_TO_DEV) ||
+	    (d40c->dma_cfg.dir == DMA_DEV_TO_DEV))
 		__d40_set_prio_rt(d40c, d40c->dma_cfg.dev_type, false);
 }
 
@@ -2400,11 +2400,11 @@ static struct dma_chan *d40_xlate(struct of_phandle_args *dma_spec,
 
 	switch (D40_DT_FLAGS_DIR(flags)) {
 	case 0:
-		cfg.dir = STEDMA40_MEM_TO_PERIPH;
+		cfg.dir = DMA_MEM_TO_DEV;
 		cfg.dst_info.big_endian = D40_DT_FLAGS_BIG_ENDIAN(flags);
 		break;
 	case 1:
-		cfg.dir = STEDMA40_PERIPH_TO_MEM;
+		cfg.dir = DMA_DEV_TO_MEM;
 		cfg.src_info.big_endian = D40_DT_FLAGS_BIG_ENDIAN(flags);
 		break;
 	}
@@ -2712,12 +2712,12 @@ static int d40_set_runtime_config(struct dma_chan *chan,
 	if (config->direction == DMA_DEV_TO_MEM) {
 		config_addr = config->src_addr;
 
-		if (cfg->dir != STEDMA40_PERIPH_TO_MEM)
+		if (cfg->dir != DMA_DEV_TO_MEM)
 			dev_dbg(d40c->base->dev,
 				"channel was not configured for peripheral "
 				"to memory transfer (%d) overriding\n",
 				cfg->dir);
-		cfg->dir = STEDMA40_PERIPH_TO_MEM;
+		cfg->dir = DMA_DEV_TO_MEM;
 
 		/* Configure the memory side */
 		if (dst_addr_width == DMA_SLAVE_BUSWIDTH_UNDEFINED)
@@ -2728,12 +2728,12 @@ static int d40_set_runtime_config(struct dma_chan *chan,
 	} else if (config->direction == DMA_MEM_TO_DEV) {
 		config_addr = config->dst_addr;
 
-		if (cfg->dir != STEDMA40_MEM_TO_PERIPH)
+		if (cfg->dir != DMA_MEM_TO_DEV)
 			dev_dbg(d40c->base->dev,
 				"channel was not configured for memory "
 				"to peripheral transfer (%d) overriding\n",
 				cfg->dir);
-		cfg->dir = STEDMA40_MEM_TO_PERIPH;
+		cfg->dir = DMA_MEM_TO_DEV;
 
 		/* Configure the memory side */
 		if (src_addr_width == DMA_SLAVE_BUSWIDTH_UNDEFINED)
@@ -2784,7 +2784,7 @@ static int d40_set_runtime_config(struct dma_chan *chan,
 
 	/* Fill in register values */
 	if (chan_is_logical(d40c)) {
-		if (d40c->dma_cfg.dir == STEDMA40_PERIPH_TO_MEM)
+		if (d40c->dma_cfg.dir == DMA_DEV_TO_MEM)
 			d40c->lcpa = d40c->base->lcpa_base +
 				d40c->dma_cfg.dev_type * D40_LCPA_CHAN_SIZE;
 		else
diff --git a/drivers/dma/ste_dma40_ll.c b/drivers/dma/ste_dma40_ll.c
index 9ab9dff..1e4b571 100644
--- a/drivers/dma/ste_dma40_ll.c
+++ b/drivers/dma/ste_dma40_ll.c
@@ -18,23 +18,23 @@ void d40_log_cfg(struct stedma40_chan_cfg *cfg,
 	u32 l1 = 0; /* src */
 
 	/* src is mem? -> increase address pos */
-	if (cfg->dir ==  STEDMA40_MEM_TO_PERIPH ||
-	    cfg->dir ==  STEDMA40_MEM_TO_MEM)
+	if (cfg->dir ==  DMA_MEM_TO_DEV ||
+	    cfg->dir ==  DMA_MEM_TO_MEM)
 		l1 |= 1 << D40_MEM_LCSP1_SCFG_INCR_POS;
 
 	/* dst is mem? -> increase address pos */
-	if (cfg->dir ==  STEDMA40_PERIPH_TO_MEM ||
-	    cfg->dir ==  STEDMA40_MEM_TO_MEM)
+	if (cfg->dir ==  DMA_DEV_TO_MEM ||
+	    cfg->dir ==  DMA_MEM_TO_MEM)
 		l3 |= 1 << D40_MEM_LCSP3_DCFG_INCR_POS;
 
 	/* src is hw? -> master port 1 */
-	if (cfg->dir ==  STEDMA40_PERIPH_TO_MEM ||
-	    cfg->dir ==  STEDMA40_PERIPH_TO_PERIPH)
+	if (cfg->dir ==  DMA_DEV_TO_MEM ||
+	    cfg->dir ==  DMA_DEV_TO_DEV)
 		l1 |= 1 << D40_MEM_LCSP1_SCFG_MST_POS;
 
 	/* dst is hw? -> master port 1 */
-	if (cfg->dir ==  STEDMA40_MEM_TO_PERIPH ||
-	    cfg->dir ==  STEDMA40_PERIPH_TO_PERIPH)
+	if (cfg->dir ==  DMA_MEM_TO_DEV ||
+	    cfg->dir ==  DMA_DEV_TO_DEV)
 		l3 |= 1 << D40_MEM_LCSP3_DCFG_MST_POS;
 
 	l3 |= 1 << D40_MEM_LCSP3_DCFG_EIM_POS;
@@ -61,8 +61,8 @@ void d40_phy_cfg(struct stedma40_chan_cfg *cfg, u32 *src_cfg, u32 *dst_cfg)
 	u32 src = 0;
 	u32 dst = 0;
 
-	if ((cfg->dir ==  STEDMA40_PERIPH_TO_MEM) ||
-	    (cfg->dir == STEDMA40_PERIPH_TO_PERIPH)) {
+	if ((cfg->dir == DMA_DEV_TO_MEM) ||
+	    (cfg->dir == DMA_DEV_TO_DEV)) {
 		/* Set master port to 1 */
 		src |= 1 << D40_SREG_CFG_MST_POS;
 		src |= D40_TYPE_TO_EVENT(cfg->dev_type);
@@ -72,8 +72,8 @@ void d40_phy_cfg(struct stedma40_chan_cfg *cfg, u32 *src_cfg, u32 *dst_cfg)
 		else
 			src |= 3 << D40_SREG_CFG_PHY_TM_POS;
 	}
-	if ((cfg->dir ==  STEDMA40_MEM_TO_PERIPH) ||
-	    (cfg->dir == STEDMA40_PERIPH_TO_PERIPH)) {
+	if ((cfg->dir == DMA_MEM_TO_DEV) ||
+	    (cfg->dir == DMA_DEV_TO_DEV)) {
 		/* Set master port to 1 */
 		dst |= 1 << D40_SREG_CFG_MST_POS;
 		dst |= D40_TYPE_TO_EVENT(cfg->dev_type);
-- 
1.7.10.4

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/