Re: [PATCH 1/2] pinctrl: add function to parse generic pinconfigproperties from a dt node

[James Hogan]

Hi Heiko,

On 10/06/13 20:40, Heiko StÃbner wrote:
> pinconf_generic_parse_dt_config() takes a node as input and generates an
> array of generic pinconfig values from the properties of this node.
> 
> As I couldn't find a mechanism to count the number of properties of a node
> the function uses internally an array to accept one of parameter and copies
> the real present options to a smaller variable at its end.
> 
> Signed-off-by: Heiko Stuebner <heiko@xxxxxxxxx>

<snip>

> @@ -139,3 +140,83 @@ void pinconf_generic_dump_config(struct pinctrl_dev *pctldev,
>  }
>  EXPORT_SYMBOL_GPL(pinconf_generic_dump_config);
>  #endif
> +
> +#ifdef CONFIG_OF
> +struct pinconf_generic_dt_params {
> +	const char * const property;
> +	enum pin_config_param param;
> +	u32 default_value;
> +};
> +
> +static struct pinconf_generic_dt_params dt_params[] = {
> +	{ "bias-disable", PIN_CONFIG_BIAS_DISABLE, 0 },
> +	{ "bias-high-impedance", PIN_CONFIG_BIAS_HIGH_IMPEDANCE, 0 },
> +	{ "bias-bus-hold", PIN_CONFIG_BIAS_BUS_HOLD, 0 },
> +	{ "bias-pull-up", PIN_CONFIG_BIAS_PULL_UP, 0 },
> +	{ "bias-pull-down", PIN_CONFIG_BIAS_PULL_DOWN, 0 },
> +	{ "bias-pull-pin-default", PIN_CONFIG_BIAS_PULL_PIN_DEFAULT, 0 },
> +	{ "drive-push-pull", PIN_CONFIG_DRIVE_PUSH_PULL, 0 },
> +	{ "drive-open-drain", PIN_CONFIG_DRIVE_OPEN_DRAIN, 0 },
> +	{ "drive-open-source", PIN_CONFIG_DRIVE_OPEN_SOURCE, 0 },
> +	{ "drive-strength", PIN_CONFIG_DRIVE_STRENGTH, 0 },
> +	{ "input-schmitt-enable", PIN_CONFIG_INPUT_SCHMITT_ENABLE, 1 },
> +	{ "input-schmitt-disable", PIN_CONFIG_INPUT_SCHMITT_ENABLE, 0 },
> +	{ "input-schmitt", PIN_CONFIG_INPUT_SCHMITT, 0 },
> +	{ "input-debounce", PIN_CONFIG_INPUT_DEBOUNCE, 0 },
> +	{ "power-source", PIN_CONFIG_POWER_SOURCE, 0 },
> +	{ "slew-rate", PIN_CONFIG_SLEW_RATE, 0 },
> +	{ "low-power-mode", PIN_CONFIG_LOW_POWER_MODE, 0 },
> +	{ "output-low", PIN_CONFIG_OUTPUT, 0, },
> +	{ "output-high", PIN_CONFIG_OUTPUT, 1, },

shouldn't half of these default to 1 instead of 0? i.e. it's much nicer
for the lone flag "bias-pull-up" to enable pull up rather than disable
it (you even do this in the DT example in the bindings doc).

Otherwise the patch looks good to me (though I haven't tried it yet).

Cheers
James

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/