[PATCH] hwmon: add support for SMSC EMC2305/03/02/01 fan controller
From: Reinhard Pfau
Date: Thu Jun 13 2013 - 06:47:24 EST
From: Reinhard Pfau <pfau@xxxxxxxx>
Add support for SMSC EMC2305, EMC2303, EMC2302, EMC2301 fan controller
chips.
The driver primary supports the EMC2305 chip which provides RPM-based
PWM control and monitoring for up to 5 fans.
According to the SMSC data sheets the EMC2303, EMC2302 and EMC2301 chips
have basically the same functionality and register layout, but support
less fans and (in case of EMC2302 and EMC2301) less possible I2C addresses.
The driver supports them, too.
The driver supports configuration via devicetree. This can also be used
to restrict the fans exposed via sysfs (see doc for details).
Signed-off-by: Reinhard Pfau <pfau@xxxxxxxx>
---
.../devicetree/bindings/hwmon/emc2305.txt | 61 ++
Documentation/hwmon/emc2305 | 33 +
MAINTAINERS | 8 +
drivers/hwmon/Kconfig | 10 +
drivers/hwmon/Makefile | 1 +
drivers/hwmon/emc2305.c | 800 ++++++++++++++++++++
6 files changed, 913 insertions(+), 0 deletions(-)
create mode 100644 Documentation/devicetree/bindings/hwmon/emc2305.txt
create mode 100644 Documentation/hwmon/emc2305
create mode 100644 drivers/hwmon/emc2305.c
diff --git a/Documentation/devicetree/bindings/hwmon/emc2305.txt b/Documentation/devicetree/bindings/hwmon/emc2305.txt
new file mode 100644
index 0000000..8e0c0dd
--- /dev/null
+++ b/Documentation/devicetree/bindings/hwmon/emc2305.txt
@@ -0,0 +1,61 @@
+EMC2305 (I2C)
+
+This device is a RPM-based PWM Fan Speed Controller for up to 5 fans.
+
+Each fan can beconfigured individually:
+
+ - pwm-enable defines the PWM mode:
+ 0: PWM is disabled
+ 3: RPM based PWM
+
+ - fan-div sets the fan divisor (for RPM mesaurement)
+ 1, 2 ,4 or 8
+
+ - fan-target sets the target RPM speed (for RPM based PWM mode)
+ max 16000 (according to data sheet)
+
+
+1) The /emc2305 node
+
+ Required properties:
+
+ - compatible : must be "smsc,emc2305"
+ - reg : I2C bus address of the device
+ - #address-cells : must be <1>
+ - #size-cells : must be <0>
+
+ The node may contain child nodes for each fan that the platform uses.
+ If no child nodes are given, all possible fan control channels are exposed.
+ If at least one child node is given, only the configured fans are exposed.
+
+ Example EMC2305 node:
+
+ emc2305@2C {
+ compatible = "smsc,emc2305";
+ reg = <0x2C>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ [ child node definitions... ]
+ }
+
+2) fan nodes
+
+ Required properties:
+
+ - reg : the fan number (0 based)
+
+ Optional properties:
+
+ - fan-div : the fan divisor setting
+ - fan-target : the fan target speed
+ - pwm-enable : PWM mode
+
+ Example EMC2305 fan node:
+
+ fan@1 {
+ reg = <1>;
+ fan-div = <4>;
+ pwm-enable = <0>;
+ };
+
diff --git a/Documentation/hwmon/emc2305 b/Documentation/hwmon/emc2305
new file mode 100644
index 0000000..4de033b
--- /dev/null
+++ b/Documentation/hwmon/emc2305
@@ -0,0 +1,33 @@
+Kernel driver emc2305
+=====================
+
+Supported chips:
+ * SMSC EMC2305, EMC2303, EMC2302, EMC2301
+ Adresses scanned: I2C 0x2c, 0x2d, 0x2e, 0x2f, 0x4c, 0x4d
+ Prefixes: 'emc2305', 'emc2303', 'emc2302', 'emc2301'
+ Datasheet: Publicly available at the SMSC website :
+ http://www.smsc.com/Products/Thermal_and_Power_Management/Fan_Controllers
+
+Authors:
+ Reinhard Pfau, Guntermann & Drunck GmbH <pfau@xxxxxxxx>
+
+Description
+-----------
+
+The SMSC EMC2305 is a fan controller for up to 5 fans.
+The EMC2303 has the same functionality but supports only up to 3 fans.
+
+The EMC2302 supports 2 fans and the EMC2301 1 fan. These chips support less
+possible I2C addresses.
+
+Fan rotation speeds are reported in RPM.
+The driver supports the RPM based PWM control to keep a fan at a desired speed.
+To enable this function for a fan, write 3 to pwm<num>_enable and the desired
+fan speed to fan<num>_target.
+
+
+Devicetree
+----------
+
+Configuration is also possible via devicetree:
+Documentation/devicetree/bindings/hwmon/emc2305.txt
diff --git a/MAINTAINERS b/MAINTAINERS
index 0c9dc71..41ddd67 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -7435,6 +7435,14 @@ S: Maintained
F: Documentation/hwmon/emc2103
F: drivers/hwmon/emc2103.c
+SMSC EMC2305 HARDWARE MONITOR DRIVER
+M: Reinhard Pfau <pfau@xxxxxxxx>
+L: lm-sensors@xxxxxxxxxxxxxx
+S: Maintained
+F: Documentation/hwmon/emc2305
+F: Documentation/devicetree/bindings/hwmon/emc2305.txt
+F: drivers/hwmon/emc2305.c
+
SMSC SCH5627 HARDWARE MONITOR DRIVER
M: Hans de Goede <hdegoede@xxxxxxxxxx>
L: lm-sensors@xxxxxxxxxxxxxx
diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
index 0428e8a..6c72441 100644
--- a/drivers/hwmon/Kconfig
+++ b/drivers/hwmon/Kconfig
@@ -1094,6 +1094,16 @@ config SENSORS_EMC2103
This driver can also be built as a module. If so, the module
will be called emc2103.
+config SENSORS_EMC2305
+ tristate "SMSC EMC2305"
+ depends on I2C
+ help
+ If you say yes here you get support for the SMSC EMC2305/EMC2303
+ fan controller chips.
+
+ This driver can also be built as a module. If so, the module
+ will be called emc2305.
+
config SENSORS_EMC6W201
tristate "SMSC EMC6W201"
depends on I2C
diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile
index d17d3e6..982752a 100644
--- a/drivers/hwmon/Makefile
+++ b/drivers/hwmon/Makefile
@@ -53,6 +53,7 @@ obj-$(CONFIG_SENSORS_DS620) += ds620.o
obj-$(CONFIG_SENSORS_DS1621) += ds1621.o
obj-$(CONFIG_SENSORS_EMC1403) += emc1403.o
obj-$(CONFIG_SENSORS_EMC2103) += emc2103.o
+obj-$(CONFIG_SENSORS_EMC2305) += emc2305.o
obj-$(CONFIG_SENSORS_EMC6W201) += emc6w201.o
obj-$(CONFIG_SENSORS_F71805F) += f71805f.o
obj-$(CONFIG_SENSORS_F71882FG) += f71882fg.o
diff --git a/drivers/hwmon/emc2305.c b/drivers/hwmon/emc2305.c
new file mode 100644
index 0000000..29acead
--- /dev/null
+++ b/drivers/hwmon/emc2305.c
@@ -0,0 +1,800 @@
+/*
+ * emc2305.c - hwmon driver for SMSC EMC2305 fan controller
+ * (C) Copyright 2013
+ * Reinhard Pfau, Guntermann & Drunck GmbH <pfau@xxxxxxxx>
+ *
+ * Based on emc2103 driver by SMSC.
+ *
+ * Datasheet available at:
+ * http://www.smsc.com/Downloads/SMSC/Downloads_Public/Data_Sheets/2305.pdf
+ *
+ * Also supports the EMC2303 fan controller which has the same functionality
+ * and register layout as EMC2305, but supports only up to 3 fans instead of 5.
+ *
+ * Also supports EMC2302 (up to 2 fans) and EMC2301 (1 fan) fan controller.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+/*
+ * TODO / IDEAS:
+ * - expose more of the configuration and features
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <linux/jiffies.h>
+#include <linux/i2c.h>
+#include <linux/hwmon.h>
+#include <linux/hwmon-sysfs.h>
+#include <linux/err.h>
+#include <linux/mutex.h>
+#include <linux/of.h>
+
+/*
+ * Addresses scanned.
+ * Listed in the same order as they appear in the EMC2305, EMC2303 data sheets.
+ *
+ * Note: these are the I2C adresses which are possible for EMC2305 and EMC2303
+ * chips.
+ * The EMC2302 supports only 0x2e (EMC2302-1) and 0x2f (EMC2302-2).
+ * The EMC2301 supports only 0x2f.
+ */
+static const unsigned short i2c_adresses[] = {
+ 0x2E,
+ 0x2F,
+ 0x2C,
+ 0x2D,
+ 0x4C,
+ 0x4D,
+ I2C_CLIENT_END
+};
+
+/*
+ * global registers
+ */
+enum {
+ REG_CONFIGURATION = 0x20,
+ REG_FAN_STATUS = 0x24,
+ REG_FAN_STALL_STATUS = 0x25,
+ REG_FAN_SPIN_STATUS = 0x26,
+ REG_DRIVE_FAIL_STATUS = 0x27,
+ REG_FAN_INTERRUPT_ENABLE = 0x29,
+ REG_PWM_POLARITY_CONFIG = 0x2a,
+ REG_PWM_OUTPUT_CONFIG = 0x2b,
+ REG_PWM_BASE_FREQ_1 = 0x2c,
+ REG_PWM_BASE_FREQ_2 = 0x2d,
+ REG_SOFTWARE_LOCK = 0xef,
+ REG_PRODUCT_FEATURES = 0xfc,
+ REG_PRODUCT_ID = 0xfd,
+ REG_MANUFACTURER_ID = 0xfe,
+ REG_REVISION = 0xff
+};
+
+/*
+ * fan specific registers
+ */
+enum {
+ REG_FAN_SETTING = 0x30,
+ REG_PWM_DIVIDE = 0x31,
+ REG_FAN_CONFIGURATION_1 = 0x32,
+ REG_FAN_CONFIGURATION_2 = 0x33,
+ REG_GAIN = 0x35,
+ REG_FAN_SPIN_UP_CONFIG = 0x36,
+ REG_FAN_MAX_STEP = 0x37,
+ REG_FAN_MINIMUM_DRIVE = 0x38,
+ REG_FAN_VALID_TACH_COUNT = 0x39,
+ REG_FAN_DRIVE_FAIL_BAND_LOW = 0x3a,
+ REG_FAN_DRIVE_FAIL_BAND_HIGH = 0x3b,
+ REG_TACH_TARGET_LOW = 0x3c,
+ REG_TACH_TARGET_HIGH = 0x3d,
+ REG_TACH_READ_HIGH = 0x3e,
+ REG_TACH_READ_LOW = 0x3f,
+};
+
+#define SEL_FAN(fan, reg) (reg + fan * 0x10)
+
+/*
+ * Factor by equations [2] and [3] from data sheet; valid for fans where the
+ * number of edges equals (poles * 2 + 1).
+ */
+#define FAN_RPM_FACTOR 3932160
+
+
+struct emc2305_fan_data {
+ bool enabled;
+ bool valid;
+ unsigned long last_updated;
+ bool rpm_control;
+ u8 multiplier;
+ u8 poles;
+ u16 target;
+ u16 tach;
+ u16 rpm_factor;
+};
+
+struct emc2305_data {
+ struct device *hwmon_dev;
+ struct mutex update_lock;
+ int fans;
+ struct emc2305_fan_data fan[5];
+};
+
+static int read_u8_from_i2c(struct i2c_client *client, u8 i2c_reg, u8 *output)
+{
+ int status = i2c_smbus_read_byte_data(client, i2c_reg);
+ if (status < 0) {
+ dev_warn(&client->dev, "reg 0x%02x, err %d\n",
+ i2c_reg, status);
+ } else {
+ *output = status;
+ }
+ return status;
+}
+
+static void read_fan_from_i2c(struct i2c_client *client, u16 *output,
+ u8 hi_addr, u8 lo_addr)
+{
+ u8 high_byte, lo_byte;
+
+ if (read_u8_from_i2c(client, hi_addr, &high_byte) < 0)
+ return;
+
+ if (read_u8_from_i2c(client, lo_addr, &lo_byte) < 0)
+ return;
+
+ *output = ((u16)high_byte << 5) | (lo_byte >> 3);
+}
+
+static void write_fan_target_to_i2c(struct i2c_client *client, int fan,
+ u16 new_target)
+{
+ const u8 lo_reg = SEL_FAN(fan, REG_TACH_TARGET_LOW);
+ const u8 hi_reg = SEL_FAN(fan, REG_TACH_TARGET_HIGH);
+ u8 high_byte = (new_target & 0x1fe0) >> 5;
+ u8 low_byte = (new_target & 0x001f) << 3;
+ i2c_smbus_write_byte_data(client, lo_reg, low_byte);
+ i2c_smbus_write_byte_data(client, hi_reg, high_byte);
+}
+
+static void read_fan_config_from_i2c(struct i2c_client *client, int fan)
+
+{
+ struct emc2305_data *data = i2c_get_clientdata(client);
+ u8 conf1;
+
+ if (read_u8_from_i2c(client, SEL_FAN(fan, REG_FAN_CONFIGURATION_1),
+ &conf1) < 0)
+ return;
+
+ data->fan[fan].rpm_control = (conf1 & 0x80) != 0;
+ data->fan[fan].multiplier = 1 << ((conf1 & 0x60) >> 5);
+ data->fan[fan].poles = ((conf1 & 0x18) >> 3) + 1;
+}
+
+static void read_fan_data(struct i2c_client *client, int fan_idx)
+{
+ struct emc2305_data *data = i2c_get_clientdata(client);
+
+ read_fan_from_i2c(client, &data->fan[fan_idx].target,
+ SEL_FAN(fan_idx, REG_TACH_TARGET_HIGH),
+ SEL_FAN(fan_idx, REG_TACH_TARGET_LOW));
+ read_fan_from_i2c(client, &data->fan[fan_idx].tach,
+ SEL_FAN(fan_idx, REG_TACH_READ_HIGH),
+ SEL_FAN(fan_idx, REG_TACH_READ_LOW));
+}
+
+static struct emc2305_fan_data *
+emc2305_update_fan(struct i2c_client *client, int fan_idx)
+{
+ struct emc2305_data *data = i2c_get_clientdata(client);
+ struct emc2305_fan_data *fan_data = &data->fan[fan_idx];
+
+ mutex_lock(&data->update_lock);
+
+ if (time_after(jiffies, fan_data->last_updated + HZ + HZ / 2)
+ || !fan_data->valid) {
+ read_fan_config_from_i2c(client, fan_idx);
+ read_fan_data(client, fan_idx);
+ fan_data->valid = true;
+ fan_data->last_updated = jiffies;
+ }
+
+ mutex_unlock(&data->update_lock);
+ return fan_data;
+}
+
+static struct emc2305_fan_data *
+emc2305_update_device_fan(struct device *dev, struct device_attribute *da)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ int fan_idx = to_sensor_dev_attr(da)->index;
+
+ return emc2305_update_fan(client, fan_idx);
+}
+
+/*
+ * set/ config functions
+ */
+
+/*
+ * Note: we also update the fan target here, because its value is
+ * determined in part by the fan clock divider. This follows the principle
+ * of least surprise; the user doesn't expect the fan target to change just
+ * because the divider changed.
+ */
+static int
+emc2305_set_fan_div(struct i2c_client *client, int fan_idx, long new_div)
+{
+ struct emc2305_data *data = i2c_get_clientdata(client);
+ struct emc2305_fan_data *fan = emc2305_update_fan(client, fan_idx);
+ const u8 reg_conf1 = SEL_FAN(fan_idx, REG_FAN_CONFIGURATION_1);
+ int new_range_bits, old_div = 8 / fan->multiplier;
+ int status = 0;
+
+ if (new_div == old_div) /* No change */
+ return 0;
+
+ switch (new_div) {
+ case 1:
+ new_range_bits = 3;
+ break;
+ case 2:
+ new_range_bits = 2;
+ break;
+ case 4:
+ new_range_bits = 1;
+ break;
+ case 8:
+ new_range_bits = 0;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ mutex_lock(&data->update_lock);
+
+ status = i2c_smbus_read_byte_data(client, reg_conf1);
+ if (status < 0) {
+ dev_dbg(&client->dev, "reg 0x%02x, err %d\n",
+ reg_conf1, status);
+ status = -EIO;
+ goto exit_unlock;
+ }
+ status &= 0x9F;
+ status |= (new_range_bits << 5);
+ status = i2c_smbus_write_byte_data(client, reg_conf1, status);
+ if (status < 0) {
+ status = -EIO;
+ goto exit_invalidate;
+ }
+
+ fan->multiplier = 8 / new_div;
+
+ /* update fan target if high byte is not disabled */
+ if ((fan->target & 0x1fe0) != 0x1fe0) {
+ u16 new_target = (fan->target * old_div) / new_div;
+ fan->target = min_t(u16, new_target, 0x1fff);
+ write_fan_target_to_i2c(client, fan_idx, fan->target);
+ }
+
+exit_invalidate:
+ /* invalidate fan data to force re-read from hardware */
+ fan->valid = false;
+exit_unlock:
+ mutex_unlock(&data->update_lock);
+ return status;
+}
+
+static int
+emc2305_set_fan_target(struct i2c_client *client, int fan_idx, long rpm_target)
+{
+ struct emc2305_data *data = i2c_get_clientdata(client);
+ struct emc2305_fan_data *fan = emc2305_update_fan(client, fan_idx);
+
+ /*
+ * Datasheet states 16000 as maximum RPM target
+ * (table 2.2 and section 4.3)
+ */
+ if ((rpm_target < 0) || (rpm_target > 16000))
+ return -EINVAL;
+
+ mutex_lock(&data->update_lock);
+
+ if (rpm_target == 0)
+ fan->target = 0x1fff;
+ else
+ fan->target = clamp_val(
+ (FAN_RPM_FACTOR * fan->multiplier) / rpm_target,
+ 0, 0x1fff);
+
+ write_fan_target_to_i2c(client, fan_idx, fan->target);
+
+ mutex_unlock(&data->update_lock);
+ return 0;
+}
+
+static int
+emc2305_set_pwm_enable(struct i2c_client *client, int fan_idx, long enable)
+{
+ struct emc2305_data *data = i2c_get_clientdata(client);
+ struct emc2305_fan_data *fan = emc2305_update_fan(client, fan_idx);
+ const u8 reg_fan_conf1 = SEL_FAN(fan_idx, REG_FAN_CONFIGURATION_1);
+ int status = 0;
+ u8 conf_reg;
+
+ mutex_lock(&data->update_lock);
+ switch (enable) {
+ case 0:
+ fan->rpm_control = false;
+ break;
+ case 3:
+ fan->rpm_control = true;
+ break;
+ default:
+ status = -EINVAL;
+ goto exit_unlock;
+ }
+
+ status = read_u8_from_i2c(client, reg_fan_conf1, &conf_reg);
+ if (status < 0) {
+ status = -EIO;
+ goto exit_unlock;
+ }
+
+ if (fan->rpm_control)
+ conf_reg |= 0x80;
+ else
+ conf_reg &= ~0x80;
+
+ status = i2c_smbus_write_byte_data(client, reg_fan_conf1, conf_reg);
+ if (status < 0)
+ status = -EIO;
+
+exit_unlock:
+ mutex_unlock(&data->update_lock);
+ return status;
+}
+
+
+/*
+ * sysfs callback functions
+ *
+ * Note:
+ * Naming of the funcs is modelled after the naming scheme described in
+ * Documentation/hwmon/sysfs-interface:
+ *
+ * For a sysfs file <type><number>_<item> the functions are named like this:
+ * the show function: show_<type>_<item>
+ * the store function: set_<type>_<item>
+ * For read only (RO) attributes of course only the show func is required.
+ *
+ * This convention allows us to define the sysfs attributes by using macros.
+ */
+
+static ssize_t
+show_fan_input(struct device *dev, struct device_attribute *da, char *buf)
+{
+ struct emc2305_fan_data *fan = emc2305_update_device_fan(dev, da);
+ int rpm = 0;
+ if (fan->tach != 0)
+ rpm = (FAN_RPM_FACTOR * fan->multiplier) / fan->tach;
+ return sprintf(buf, "%d\n", rpm);
+}
+
+static ssize_t
+show_fan_fault(struct device *dev, struct device_attribute *da, char *buf)
+{
+ struct emc2305_fan_data *fan = emc2305_update_device_fan(dev, da);
+ bool fault = ((fan->tach & 0x1fe0) == 0x1fe0);
+ return sprintf(buf, "%d\n", fault ? 1 : 0);
+}
+
+static ssize_t
+show_fan_div(struct device *dev, struct device_attribute *da, char *buf)
+{
+ struct emc2305_fan_data *fan = emc2305_update_device_fan(dev, da);
+ int fan_div = 8 / fan->multiplier;
+ return sprintf(buf, "%d\n", fan_div);
+}
+
+static ssize_t
+set_fan_div(struct device *dev, struct device_attribute *da,
+ const char *buf, size_t count)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ int fan_idx = to_sensor_dev_attr(da)->index;
+ long new_div;
+ int status;
+
+ status = kstrtol(buf, 10, &new_div);
+ if (status < 0)
+ return -EINVAL;
+
+ status = emc2305_set_fan_div(client, fan_idx, new_div);
+ if (status < 0)
+ return status;
+
+ return count;
+}
+
+static ssize_t
+show_fan_target(struct device *dev, struct device_attribute *da, char *buf)
+{
+ struct emc2305_fan_data *fan = emc2305_update_device_fan(dev, da);
+ int rpm = 0;
+
+ /* high byte of 0xff indicates disabled so return 0 */
+ if ((fan->target != 0) && ((fan->target & 0x1fe0) != 0x1fe0))
+ rpm = (FAN_RPM_FACTOR * fan->multiplier)
+ / fan->target;
+
+ return sprintf(buf, "%d\n", rpm);
+}
+
+static ssize_t set_fan_target(struct device *dev, struct device_attribute *da,
+ const char *buf, size_t count)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ int fan_idx = to_sensor_dev_attr(da)->index;
+ long rpm_target;
+ int status;
+
+ status = kstrtol(buf, 10, &rpm_target);
+ if (status < 0)
+ return -EINVAL;
+
+ status = emc2305_set_fan_target(client, fan_idx, rpm_target);
+ if (status < 0)
+ return status;
+
+ return count;
+}
+
+static ssize_t
+show_pwm_enable(struct device *dev, struct device_attribute *da, char *buf)
+{
+ struct emc2305_fan_data *fan = emc2305_update_device_fan(dev, da);
+ return sprintf(buf, "%d\n", fan->rpm_control ? 3 : 0);
+}
+
+static ssize_t set_pwm_enable(struct device *dev, struct device_attribute *da,
+ const char *buf, size_t count)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ int fan_idx = to_sensor_dev_attr(da)->index;
+ long new_value;
+ int status;
+
+ status = kstrtol(buf, 10, &new_value);
+ if (status < 0)
+ return -EINVAL;
+ status = emc2305_set_pwm_enable(client, fan_idx, new_value);
+ return count;
+}
+
+/* define a read only attribute */
+#define EMC2305_ATTR_RO(_type, _item, _num) \
+ SENSOR_ATTR(_type ## _num ## _ ## _item, S_IRUGO, \
+ show_## _type ## _ ## _item, NULL, _num - 1)
+
+/* define a read/write attribute */
+#define EMC2305_ATTR_RW(_type, _item, _num) \
+ SENSOR_ATTR(_type ## _num ## _ ## _item, S_IRUGO | S_IWUSR, \
+ show_## _type ##_ ## _item, \
+ set_## _type ## _ ## _item, _num - 1)
+
+/* defines the attributes for a single fan */
+#define EMC2305_DEFINE_FAN_ATTRS(_num) \
+ static const \
+ struct sensor_device_attribute emc2305_attr_fan ## _num[] = { \
+ EMC2305_ATTR_RO(fan, input, _num), \
+ EMC2305_ATTR_RO(fan, fault, _num), \
+ EMC2305_ATTR_RW(fan, div, _num), \
+ EMC2305_ATTR_RW(fan, target, _num), \
+ EMC2305_ATTR_RW(pwm, enable, _num) \
+ }
+
+#define EMC2305_NUM_FAN_ATTRS ARRAY_SIZE(emc2305_attr_fan1)
+
+/* common attributes for EMC2303 and EMC2305 */
+static const struct sensor_device_attribute emc2305_attr_common[] = {
+};
+
+/* fan attributes for the single fans */
+EMC2305_DEFINE_FAN_ATTRS(1);
+EMC2305_DEFINE_FAN_ATTRS(2);
+EMC2305_DEFINE_FAN_ATTRS(3);
+EMC2305_DEFINE_FAN_ATTRS(4);
+EMC2305_DEFINE_FAN_ATTRS(5);
+
+/* fan attributes */
+static const struct sensor_device_attribute *emc2305_fan_attrs[] = {
+ emc2305_attr_fan1,
+ emc2305_attr_fan2,
+ emc2305_attr_fan3,
+ emc2305_attr_fan4,
+ emc2305_attr_fan5,
+};
+
+/*
+ * driver interface
+ */
+
+static int emc2305_remove(struct i2c_client *client)
+{
+ struct emc2305_data *data = i2c_get_clientdata(client);
+ int fan_idx, i;
+
+ hwmon_device_unregister(data->hwmon_dev);
+
+ for (fan_idx = 0; fan_idx < data->fans; ++fan_idx)
+ for (i = 0; i < EMC2305_NUM_FAN_ATTRS; ++i)
+ device_remove_file(
+ &client->dev,
+ &emc2305_fan_attrs[fan_idx][i].dev_attr);
+
+ for (i = 0; i < ARRAY_SIZE(emc2305_attr_common); ++i)
+ device_remove_file(&client->dev,
+ &emc2305_attr_common[i].dev_attr);
+
+ kfree(data);
+ return 0;
+}
+
+
+#ifdef CONFIG_OF
+/*
+ * device tree support
+ */
+
+struct of_fan_attribute {
+ const char *name;
+ int (*set)(struct i2c_client*, int, long);
+};
+
+struct of_fan_attribute of_fan_attributes[] = {
+ {"fan-div", emc2305_set_fan_div},
+ {"fan-target", emc2305_set_fan_target},
+ {"pwm-enable", emc2305_set_pwm_enable},
+ {NULL, NULL}
+};
+
+static int emc2305_config_of(struct i2c_client *client)
+{
+ struct emc2305_data *data = i2c_get_clientdata(client);
+ struct device_node *node;
+ unsigned int fan_idx;
+
+ if (!client->dev.of_node)
+ return -EINVAL;
+ if (!of_get_next_child(client->dev.of_node, NULL))
+ return 0;
+
+ for (fan_idx = 0; fan_idx < data->fans; ++fan_idx)
+ data->fan[fan_idx].enabled = false;
+
+ for_each_child_of_node(client->dev.of_node, node) {
+ const __be32 *property;
+ int len;
+ struct of_fan_attribute *attr;
+
+ property = of_get_property(node, "reg", &len);
+ if (!property || len != sizeof(int)) {
+ dev_err(&client->dev, "invalid reg on %s\n",
+ node->full_name);
+ continue;
+ }
+
+ fan_idx = be32_to_cpup(property);
+ if (fan_idx >= data->fans) {
+ dev_err(&client->dev,
+ "invalid fan index %d on %s\n",
+ fan_idx, node->full_name);
+ continue;
+ }
+
+ data->fan[fan_idx].enabled = true;
+
+ for (attr = of_fan_attributes; attr->name; ++attr) {
+ int status = 0;
+ long value;
+ property = of_get_property(node, attr->name, &len);
+ if (!property)
+ continue;
+ if (len != sizeof(int)) {
+ dev_err(&client->dev, "invalid %s on %s\n",
+ attr->name, node->full_name);
+ continue;
+ }
+ value = be32_to_cpup(property);
+ status = attr->set(client, fan_idx, value);
+ if (status == -EINVAL) {
+ dev_err(&client->dev,
+ "invalid value for %s on %s\n",
+ attr->name, node->full_name);
+ }
+ }
+ }
+
+ return 0;
+}
+
+#endif
+
+static void emc2305_get_config(struct i2c_client *client)
+{
+ int i;
+ struct emc2305_data *data = i2c_get_clientdata(client);
+
+ for (i = 0; i < data->fans; ++i) {
+ data->fan[i].enabled = true;
+ emc2305_update_fan(client, i);
+ }
+
+#ifdef CONFIG_OF
+ emc2305_config_of(client);
+#endif
+
+}
+
+static int
+emc2305_probe(struct i2c_client *client, const struct i2c_device_id *id)
+{
+ struct emc2305_data *data;
+ int status;
+ int i;
+ int fan_idx;
+
+ if (!i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_BYTE_DATA))
+ return -EIO;
+
+ data = kzalloc(sizeof(struct emc2305_data), GFP_KERNEL);
+ if (!data)
+ return -ENOMEM;
+
+ i2c_set_clientdata(client, data);
+ mutex_init(&data->update_lock);
+
+ status = i2c_smbus_read_byte_data(client, REG_PRODUCT_ID);
+ switch (status) {
+ case 0x34: /* EMC2305 */
+ data->fans = 5;
+ break;
+ case 0x35: /* EMC2303 */
+ data->fans = 3;
+ break;
+ case 0x36: /* EMC2302 */
+ data->fans = 2;
+ break;
+ case 0x37: /* EMC2301 */
+ data->fans = 1;
+ break;
+ default:
+ if (status >= 0)
+ status = -EINVAL;
+ goto exit_free;
+ }
+
+ emc2305_get_config(client);
+
+ for (i = 0; i < ARRAY_SIZE(emc2305_attr_common); ++i) {
+ status = device_create_file(&client->dev,
+ &emc2305_attr_common[i].dev_attr);
+ if (status)
+ goto exit_remove;
+ }
+ for (fan_idx = 0; fan_idx < data->fans; ++fan_idx)
+ for (i = 0; i < EMC2305_NUM_FAN_ATTRS; ++i) {
+ if (!data->fan[fan_idx].enabled)
+ continue;
+ status = device_create_file(
+ &client->dev,
+ &emc2305_fan_attrs[fan_idx][i].dev_attr);
+ if (status)
+ goto exit_remove_fans;
+ }
+
+ data->hwmon_dev = hwmon_device_register(&client->dev);
+ if (IS_ERR(data->hwmon_dev)) {
+ status = PTR_ERR(data->hwmon_dev);
+ goto exit_remove_fans;
+ }
+
+ dev_info(&client->dev, "%s: sensor '%s'\n",
+ dev_name(data->hwmon_dev), client->name);
+
+ return 0;
+
+exit_remove_fans:
+ for (fan_idx = 0; fan_idx < data->fans; ++fan_idx)
+ for (i = 0; i < EMC2305_NUM_FAN_ATTRS; ++i)
+ device_remove_file(
+ &client->dev,
+ &emc2305_fan_attrs[fan_idx][i].dev_attr);
+
+exit_remove:
+ for (i = 0; i < ARRAY_SIZE(emc2305_attr_common); ++i)
+ device_remove_file(&client->dev,
+ &emc2305_attr_common[i].dev_attr);
+exit_free:
+ kfree(data);
+ return status;
+}
+
+static const struct i2c_device_id emc2305_id[] = {
+ { "emc2305", 0 },
+ { "emc2303", 0 },
+ { "emc2302", 0 },
+ { "emc2301", 0 },
+ { }
+};
+MODULE_DEVICE_TABLE(i2c, emc2305_id);
+
+/* Return 0 if detection is successful, -ENODEV otherwise */
+static int
+emc2305_detect(struct i2c_client *new_client, struct i2c_board_info *info)
+{
+ struct i2c_adapter *adapter = new_client->adapter;
+ int manufacturer, product;
+
+ if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA))
+ return -ENODEV;
+
+ manufacturer =
+ i2c_smbus_read_byte_data(new_client, REG_MANUFACTURER_ID);
+ if (manufacturer != 0x5D)
+ return -ENODEV;
+
+ product = i2c_smbus_read_byte_data(new_client, REG_PRODUCT_ID);
+
+ switch (product) {
+ case 0x34:
+ strlcpy(info->type, "emc2305", I2C_NAME_SIZE);
+ break;
+ case 0x35:
+ strlcpy(info->type, "emc2303", I2C_NAME_SIZE);
+ break;
+ case 0x36:
+ strlcpy(info->type, "emc2302", I2C_NAME_SIZE);
+ break;
+ case 0x37:
+ strlcpy(info->type, "emc2301", I2C_NAME_SIZE);
+ break;
+ default:
+ return -ENODEV;
+ }
+
+ return 0;
+}
+
+static struct i2c_driver emc2305_driver = {
+ .class = I2C_CLASS_HWMON,
+ .driver = {
+ .name = "emc2305",
+ },
+ .probe = emc2305_probe,
+ .remove = emc2305_remove,
+ .id_table = emc2305_id,
+ .detect = emc2305_detect,
+ .address_list = i2c_adresses,
+};
+
+module_i2c_driver(emc2305_driver);
+
+MODULE_AUTHOR("Reinhard Pfau <pfau@xxxxxxxx>");
+MODULE_DESCRIPTION("SMSC EMC2305 hwmon driver");
+MODULE_LICENSE("GPL");
--
1.7.2.5
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/