Re: linux-next: Tree for Jun 28 [ call-trace: workqueue | drmreleated? ]

[Sedat Dilek]

On Fri, Jun 28, 2013 at 9:33 AM, Stephen Rothwell <sfr@xxxxxxxxxxxxxxxx> wrote:
> Hi all,
>
> Changes since 20130627:
>
> This tree produces the following warning when built for many (all?)
> configs (it has been fixed in the drm tree):
>
> drivers/video/Kconfig:42:error: recursive dependency detected!
> drivers/video/Kconfig:42:       symbol FB is selected by DRM_KMS_HELPER
> drivers/gpu/drm/Kconfig:29:     symbol DRM_KMS_HELPER is selected by DRM_OMAP
> drivers/gpu/drm/omapdrm/Kconfig:2:      symbol DRM_OMAP depends on FB_OMAP2
> drivers/video/omap2/omapfb/Kconfig:1:   symbol FB_OMAP2 depends on FB
>
> The arm-soc tree gained a conflict against the mfd tree.
>
> I applied a patch to the akpm tree to remove a lot of warnings.
>
> ----------------------------------------------------------------------------
>

[ CC wq and drm(-intel) folks ]

With next-20130628 I see the following call-trace:

[   11.941618] ------------[ cut here ]------------
[   11.941624] WARNING: CPU: 0 PID: 675 at kernel/workqueue.c:1445
__queue_delayed_work+0x18c/0x1a0()
[   11.941626] Modules linked in: i915(+) snd_page_alloc iwlwifi
snd_seq_midi snd_seq_midi_event btusb psmouse snd_rawmidi snd_seq
bluetooth cfg80211 i2c_algo_bit snd_timer samsung_laptop serio_raw
snd_seq_device drm_kms_helper lpc_ich drm snd wmi mac_hid soundcore
video lp parport hid_generic usbhid hid usb_storage r8169 mii
[   11.941651] CPU: 0 PID: 675 Comm: modprobe Not tainted
3.10.0-rc7-next20130628-1-iniza-small #1
[   11.941653] Hardware name: SAMSUNG ELECTRONICS CO., LTD.
530U3BI/530U4BI/530U4BH/530U3BI/530U4BI/530U4BH, BIOS 13XK 03/28/2013
[   11.941655]  00000000000005a5 ffff88010b5596a8 ffffffff816db223
0000000000001908
[   11.941658]  0000000000000000 ffff88010b5596e8 ffffffff810661cc
ffffffffa00d3341
[   11.941661]  0000000000000100 ffff880119e72000 ffff88010765a000
0000000000000003
[   11.941664] Call Trace:
[   11.941671]  [<ffffffff816db223>] dump_stack+0x46/0x58
[   11.941675]  [<ffffffff810661cc>] warn_slowpath_common+0x8c/0xc0
[   11.941679]  [<ffffffff8106621a>] warn_slowpath_null+0x1a/0x20
[   11.941682]  [<ffffffff810845ac>] __queue_delayed_work+0x18c/0x1a0
[   11.941685]  [<ffffffff8108460d>] queue_delayed_work_on+0x4d/0x60
[   11.941691]  [<ffffffffa00f2950>]
drm_helper_probe_single_connector_modes+0x270/0x420 [drm_kms_helper]
[   11.941696]  [<ffffffffa00f0f12>]
drm_fb_helper_initial_config+0x1c2/0x550 [drm_kms_helper]
[   11.941700]  [<ffffffffa00f1721>] ?
drm_fb_helper_single_add_all_connectors+0x81/0xe0 [drm_kms_helper]
[   11.941705]  [<ffffffff81193f7c>] ? kmem_cache_alloc_trace+0x1bc/0x1f0
[   11.941725]  [<ffffffffa024c481>] ? i915_write32+0x81/0x130 [i915]
[   11.941748]  [<ffffffffa02a2ee1>] intel_fbdev_initial_config+0x21/0x30 [i915]
[   11.941763]  [<ffffffffa0250512>] i915_driver_load+0xe32/0xe60 [i915]
[   11.941777]  [<ffffffffa00b1c01>] drm_get_pci_dev+0x181/0x2a0 [drm]
[   11.941781]  [<ffffffff81376add>] ? do_raw_spin_unlock+0x5d/0xb0
[   11.941794]  [<ffffffffa024b6e6>] i915_pci_probe+0x36/0x70 [i915]
[   11.941799]  [<ffffffff813954cb>] local_pci_probe+0x4b/0x80
[   11.941801]  [<ffffffff81396da1>] pci_device_probe+0x101/0x120
[   11.941806]  [<ffffffff814736bb>] driver_probe_device+0x7b/0x240
[   11.941809]  [<ffffffff8147392b>] __driver_attach+0xab/0xb0
[   11.941813]  [<ffffffff81473880>] ? driver_probe_device+0x240/0x240
[   11.941816]  [<ffffffff814719be>] bus_for_each_dev+0x5e/0x90
[   11.941819]  [<ffffffff814731de>] driver_attach+0x1e/0x20
[   11.941823]  [<ffffffff81472cd4>] bus_add_driver+0x104/0x270
[   11.941826]  [<ffffffff81473e8d>] driver_register+0x7d/0x160
[   11.941830]  [<ffffffff81395d24>] __pci_register_driver+0x64/0x70
[   11.941833]  [<ffffffffa02ee000>] ? 0xffffffffa02edfff
[   11.941842]  [<ffffffffa00b1e3a>] drm_pci_init+0x11a/0x130 [drm]
[   11.941844]  [<ffffffffa02ee000>] ? 0xffffffffa02edfff
[   11.941858]  [<ffffffffa02ee066>] i915_init+0x66/0x68 [i915]
[   11.941861]  [<ffffffff8100207e>] do_one_initcall+0x4e/0x180
[   11.941865]  [<ffffffff810584a3>] ? set_memory_nx+0x43/0x50
[   11.941869]  [<ffffffff810d09e9>] load_module+0x1cf9/0x2620
[   11.941872]  [<ffffffff810cd880>] ? show_initstate+0x50/0x50
[   11.941875]  [<ffffffff810d13bc>] SyS_init_module+0xac/0xd0
[   11.941879]  [<ffffffff816ec12f>] tracesys+0xe1/0xe6
[   11.941881] ---[ end trace a06c6f52b0f09abe ]---

My dmesg and kernel-config are attached.

( I have seen there were new commits in drm-next which did not hit
today'n -next. )

- Sedat -
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 3.10.0-rc7-next20130628-1-iniza-small (sedat.dilek@xxxxxxxxx@fambox) (gcc version 4.6.3 (Ubuntu/Linaro 4.6.3-1ubuntu5) ) #1 SMP Fri Jun 28 09:56:38 CEST 2013
[    0.000000] Command line: BOOT_IMAGE=/vmlinuz.next root=UUID=001AADA61AAD9964 loop=/ubuntu/disks/root.disk ro
[    0.000000] KERNEL supported cpus:
[    0.000000]   Intel GenuineIntel
[    0.000000]   AMD AuthenticAMD
[    0.000000]   Centaur CentaurHauls
[    0.000000] Disabled fast string operations
[    0.000000] e820: BIOS-provided physical RAM map:
[    0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009d7ff] usable
[    0.000000] BIOS-e820: [mem 0x000000000009d800-0x000000000009ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000001fffffff] usable
[    0.000000] BIOS-e820: [mem 0x0000000020000000-0x00000000201fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000020200000-0x000000003fffffff] usable
[    0.000000] BIOS-e820: [mem 0x0000000040000000-0x00000000401fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000040200000-0x00000000d9c9efff] usable
[    0.000000] BIOS-e820: [mem 0x00000000d9c9f000-0x00000000dae7efff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000dae7f000-0x00000000daf9efff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x00000000daf9f000-0x00000000daffefff] ACPI data
[    0.000000] BIOS-e820: [mem 0x00000000dafff000-0x00000000daffffff] usable
[    0.000000] BIOS-e820: [mem 0x00000000db000000-0x00000000df9fffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000f8000000-0x00000000fbffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed08000-0x00000000fed08fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed10000-0x00000000fed19fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000ffd80000-0x00000000ffffffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000011fdfffff] usable
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] SMBIOS 2.6 present.
[    0.000000] DMI: SAMSUNG ELECTRONICS CO., LTD. 530U3BI/530U4BI/530U4BH/530U3BI/530U4BI/530U4BH, BIOS 13XK 03/28/2013
[    0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[    0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[    0.000000] No AGP bridge found
[    0.000000] e820: last_pfn = 0x11fe00 max_arch_pfn = 0x400000000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF uncachable
[    0.000000]   C0000-FFFFF write-protect
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 000000000 mask F80000000 write-back
[    0.000000]   1 base 080000000 mask FC0000000 write-back
[    0.000000]   2 base 0C0000000 mask FE0000000 write-back
[    0.000000]   3 base 0DC000000 mask FFC000000 uncachable
[    0.000000]   4 base 0DB000000 mask FFF000000 uncachable
[    0.000000]   5 base 100000000 mask FE0000000 write-back
[    0.000000]   6 base 11FE00000 mask FFFE00000 uncachable
[    0.000000]   7 base 0FFC00000 mask FFFC00000 write-protect
[    0.000000]   8 disabled
[    0.000000]   9 disabled
[    0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[    0.000000] e820: last_pfn = 0xdb000 max_arch_pfn = 0x400000000
[    0.000000] found SMP MP-table at [mem 0x000f00e0-0x000f00ef] mapped at [ffff8800000f00e0]
[    0.000000] Scanning 1 areas for low memory corruption
[    0.000000] Base memory trampoline at [ffff880000097000] 97000 size 24576
[    0.000000] reserving inaccessible SNB gfx pages
[    0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[    0.000000]  [mem 0x00000000-0x000fffff] page 4k
[    0.000000] BRK [0x0204b000, 0x0204bfff] PGTABLE
[    0.000000] BRK [0x0204c000, 0x0204cfff] PGTABLE
[    0.000000] BRK [0x0204d000, 0x0204dfff] PGTABLE
[    0.000000] init_memory_mapping: [mem 0x11fc00000-0x11fdfffff]
[    0.000000]  [mem 0x11fc00000-0x11fdfffff] page 2M
[    0.000000] BRK [0x0204e000, 0x0204efff] PGTABLE
[    0.000000] init_memory_mapping: [mem 0x11c000000-0x11fbfffff]
[    0.000000]  [mem 0x11c000000-0x11fbfffff] page 2M
[    0.000000] init_memory_mapping: [mem 0x100000000-0x11bffffff]
[    0.000000]  [mem 0x100000000-0x11bffffff] page 2M
[    0.000000] init_memory_mapping: [mem 0x00100000-0x1fffffff]
[    0.000000]  [mem 0x00100000-0x001fffff] page 4k
[    0.000000]  [mem 0x00200000-0x1fffffff] page 2M
[    0.000000] init_memory_mapping: [mem 0x20200000-0x3fffffff]
[    0.000000]  [mem 0x20200000-0x3fffffff] page 2M
[    0.000000] init_memory_mapping: [mem 0x40200000-0xd9c9efff]
[    0.000000]  [mem 0x40200000-0xd9bfffff] page 2M
[    0.000000]  [mem 0xd9c00000-0xd9c9efff] page 4k
[    0.000000] BRK [0x0204f000, 0x0204ffff] PGTABLE
[    0.000000] init_memory_mapping: [mem 0xdafff000-0xdaffffff]
[    0.000000]  [mem 0xdafff000-0xdaffffff] page 4k
[    0.000000] RAMDISK: [mem 0x37966000-0x37caafff]
[    0.000000] ACPI: RSDP 00000000000f0100 00024 (v02 SECCSD)
[    0.000000] ACPI: XSDT 00000000daffe170 0008C (v01 SECCSD LH43STAR 00000002 PTEC 00000002)
[    0.000000] ACPI: FACP 00000000dafef000 0010C (v05 SECCSD LH43STAR 00000002 PTL  00000002)
[    0.000000] ACPI: DSDT 00000000daff2000 083AC (v02 SECCSD  SNB-CPT 00000000 INTL 20061109)
[    0.000000] ACPI: FACS 00000000daf47000 00040
[    0.000000] ACPI: SLIC 00000000daffd000 00176 (v01 SECCSD LH43STAR 00000002 PTEC 00000001)
[    0.000000] ACPI: SSDT 00000000daffb000 01068 (v01 SECCSD PtidDevc 00001000 INTL 20061109)
[    0.000000] ACPI: ASF! 00000000daff1000 000A5 (v32 SECCSD LH43STAR 00000002 PTL  00000002)
[    0.000000] ACPI: HPET 00000000dafee000 00038 (v01 SECCSD LH43STAR 00000002 PTL  00000002)
[    0.000000] ACPI: APIC 00000000dafed000 00098 (v03 SECCSD LH43STAR 00000002 PTL  00000002)
[    0.000000] ACPI: MCFG 00000000dafec000 0003C (v01 SECCSD LH43STAR 00000002 PTL  00000002)
[    0.000000] ACPI: SSDT 00000000dafeb000 00804 (v01  PmRef  Cpu0Ist 00003000 INTL 20061109)
[    0.000000] ACPI: SSDT 00000000dafea000 00996 (v01  PmRef    CpuPm 00003000 INTL 20061109)
[    0.000000] ACPI: UEFI 00000000dafe9000 0003E (v01 SECCSD LH43STAR 00000002 PTL  00000002)
[    0.000000] ACPI: UEFI 00000000dafe8000 00042 (v01 PTL      COMBUF 00000001 PTL  00000001)
[    0.000000] ACPI: UEFI 00000000dafe7000 0026A (v01 SECCSD LH43STAR 00000002 PTL  00000002)
[    0.000000] ACPI: SSDT 00000000dafe6000 000D0 (v01   Iffs  IffsAsl 00003000 INTL 20061109)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] No NUMA configuration found
[    0.000000] Faking a node at [mem 0x0000000000000000-0x000000011fdfffff]
[    0.000000] Initmem setup node 0 [mem 0x00000000-0x11fdfffff]
[    0.000000]   NODE_DATA [mem 0x11fdf7000-0x11fdfbfff]
[    0.000000]  [ffffea0000000000-ffffea0003ffffff] PMD -> [ffff88011b400000-ffff88011edfffff] on node 0
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x00001000-0x00ffffff]
[    0.000000]   DMA32    [mem 0x01000000-0xffffffff]
[    0.000000]   Normal   [mem 0x100000000-0x11fdfffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00001000-0x0009cfff]
[    0.000000]   node   0: [mem 0x00100000-0x1fffffff]
[    0.000000]   node   0: [mem 0x20200000-0x3fffffff]
[    0.000000]   node   0: [mem 0x40200000-0xd9c9efff]
[    0.000000]   node   0: [mem 0xdafff000-0xdaffffff]
[    0.000000]   node   0: [mem 0x100000000-0x11fdfffff]
[    0.000000] On node 0 totalpages: 1021500
[    0.000000]   DMA zone: 56 pages used for memmap
[    0.000000]   DMA zone: 156 pages reserved
[    0.000000]   DMA zone: 3996 pages, LIFO batch:0
[    0.000000]   DMA32 zone: 12127 pages used for memmap
[    0.000000]   DMA32 zone: 886944 pages, LIFO batch:31
[    0.000000]   Normal zone: 1785 pages used for memmap
[    0.000000]   Normal zone: 130560 pages, LIFO batch:31
[    0.000000] ACPI: PM-Timer IO Port: 0x408
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x00] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x00] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x00] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x08] lapic_id[0x00] disabled)
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x0e] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 14, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] ACPI: HPET id: 0x8086a301 base: 0xfed00000
[    0.000000] smpboot: Allowing 8 CPUs, 4 hotplug CPUs
[    0.000000] nr_irqs_gsi: 40
[    0.000000] PM: Registered nosave memory: [mem 0x0009d000-0x0009dfff]
[    0.000000] PM: Registered nosave memory: [mem 0x0009e000-0x0009ffff]
[    0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000dffff]
[    0.000000] PM: Registered nosave memory: [mem 0x000e0000-0x000fffff]
[    0.000000] PM: Registered nosave memory: [mem 0x20000000-0x201fffff]
[    0.000000] PM: Registered nosave memory: [mem 0x40000000-0x401fffff]
[    0.000000] PM: Registered nosave memory: [mem 0xd9c9f000-0xdae7efff]
[    0.000000] PM: Registered nosave memory: [mem 0xdae7f000-0xdaf9efff]
[    0.000000] PM: Registered nosave memory: [mem 0xdaf9f000-0xdaffefff]
[    0.000000] PM: Registered nosave memory: [mem 0xdb000000-0xdf9fffff]
[    0.000000] PM: Registered nosave memory: [mem 0xdfa00000-0xf7ffffff]
[    0.000000] PM: Registered nosave memory: [mem 0xf8000000-0xfbffffff]
[    0.000000] PM: Registered nosave memory: [mem 0xfc000000-0xfebfffff]
[    0.000000] PM: Registered nosave memory: [mem 0xfec00000-0xfec00fff]
[    0.000000] PM: Registered nosave memory: [mem 0xfec01000-0xfed07fff]
[    0.000000] PM: Registered nosave memory: [mem 0xfed08000-0xfed08fff]
[    0.000000] PM: Registered nosave memory: [mem 0xfed09000-0xfed0ffff]
[    0.000000] PM: Registered nosave memory: [mem 0xfed10000-0xfed19fff]
[    0.000000] PM: Registered nosave memory: [mem 0xfed1a000-0xfed1bfff]
[    0.000000] PM: Registered nosave memory: [mem 0xfed1c000-0xfed1ffff]
[    0.000000] PM: Registered nosave memory: [mem 0xfed20000-0xfedfffff]
[    0.000000] PM: Registered nosave memory: [mem 0xfee00000-0xfee00fff]
[    0.000000] PM: Registered nosave memory: [mem 0xfee01000-0xffd7ffff]
[    0.000000] PM: Registered nosave memory: [mem 0xffd80000-0xffffffff]
[    0.000000] e820: [mem 0xdfa00000-0xf7ffffff] available for PCI devices
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] setup_percpu: NR_CPUS:256 nr_cpumask_bits:256 nr_cpu_ids:8 nr_node_ids:1
[    0.000000] PERCPU: Embedded 29 pages/cpu @ffff88011fa00000 s87680 r8192 d22912 u262144
[    0.000000] pcpu-alloc: s87680 r8192 d22912 u262144 alloc=1*2097152
[    0.000000] pcpu-alloc: [0] 0 1 2 3 4 5 6 7 
[    0.000000] Built 1 zonelists in Node order, mobility grouping on.  Total pages: 1007376
[    0.000000] Policy zone: Normal
[    0.000000] Kernel command line: BOOT_IMAGE=/vmlinuz.next root=UUID=001AADA61AAD9964 loop=/ubuntu/disks/root.disk ro
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] xsave: enabled xstate_bv 0x7, cntxt size 0x340
[    0.000000] Checking aperture...
[    0.000000] No AGP bridge found
[    0.000000] Calgary: detecting Calgary via BIOS EBDA area
[    0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[    0.000000] Memory: 3938472K/4086000K available (7105K kernel code, 1042K rwdata, 3124K rodata, 1332K init, 1984K bss, 147528K reserved)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=8.
[    0.000000] NR_IRQS:16640 nr_irqs:744 16
[    0.000000] Console: colour VGA+ 80x25
[    0.000000] console [tty0] enabled
[    0.000000] allocated 16777216 bytes of page_cgroup
[    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    0.000000] ODEBUG: 0 of 0 active objects replaced
[    0.000000] hpet clockevent registered
[    0.000000] tsc: Fast TSC calibration using PIT
[    0.004000] tsc: Detected 1596.477 MHz processor
[    0.000003] Calibrating delay loop (skipped), value calculated using timer frequency.. 3192.95 BogoMIPS (lpj=6385908)
[    0.000080] pid_max: default: 32768 minimum: 301
[    0.000245] Security Framework initialized
[    0.000292] AppArmor: AppArmor initialized
[    0.000329] Yama: becoming mindful.
[    0.000749] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[    0.001856] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.002358] Mount-cache hash table entries: 256
[    0.002911] Initializing cgroup subsys memory
[    0.003011] Initializing cgroup subsys devices
[    0.003049] Initializing cgroup subsys freezer
[    0.003087] Initializing cgroup subsys blkio
[    0.003124] Initializing cgroup subsys perf_event
[    0.003164] Initializing cgroup subsys hugetlb
[    0.003250] Disabled fast string operations
[    0.003288] CPU: Physical Processor ID: 0
[    0.003324] CPU: Processor Core ID: 0
[    0.003364] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
[    0.003364] ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
[    0.003430] mce: CPU supports 7 MCE banks
[    0.003481] CPU0: Thermal monitoring enabled (TM1)
[    0.003526] Last level iTLB entries: 4KB 512, 2MB 0, 4MB 0
[    0.003526] Last level dTLB entries: 4KB 512, 2MB 32, 4MB 32
[    0.003526] tlb_flushall_shift: 5
[    0.003699] Freeing SMP alternatives memory: 24K (ffffffff81e53000 - ffffffff81e59000)
[    0.004790] ACPI: Core revision 20130517
[    0.015584] ACPI: All ACPI Tables successfully acquired
[    0.030309] ftrace: allocating 27039 entries in 106 pages
[    0.045595] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.085297] smpboot: CPU0: Intel(R) Core(TM) i5-2467M CPU @ 1.60GHz (fam: 06, model: 2a, stepping: 07)
[    0.085910] TSC deadline timer enabled
[    0.085923] Performance Events: PEBS fmt1+, 16-deep LBR, SandyBridge events, full-width counters, Intel PMU driver.
[    0.086072] ... version:                3
[    0.086107] ... bit width:              48
[    0.086143] ... generic registers:      4
[    0.086179] ... value mask:             0000ffffffffffff
[    0.086217] ... max period:             0000ffffffffffff
[    0.086255] ... fixed-purpose events:   3
[    0.086291] ... event mask:             000000070000000f
[    0.099409] Disabled fast string operations
[    0.102596] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[    0.114174] Disabled fast string operations
[    0.127886] Disabled fast string operations
[    0.088336] smpboot: Booting Node   0, Processors  #1 #2 #3
[    0.130021] Brought up 4 CPUs
[    0.130127] smpboot: Total of 4 processors activated (12771.81 BogoMIPS)
[    0.134233] devtmpfs: initialized
[    0.136270] EVM: security.selinux
[    0.136305] EVM: security.SMACK64
[    0.136340] EVM: security.capability
[    0.136461] PM: Registering ACPI NVS region [mem 0xdae7f000-0xdaf9efff] (1179648 bytes)
[    0.138014] regulator-dummy: no parameters
[    0.138203] NET: Registered protocol family 16
[    0.138580] ACPI: bus type PCI registered
[    0.138730] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000)
[    0.138788] PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820
[    0.145603] PCI: Using configuration type 1 for base access
[    0.148982] bio: create slab <bio-0> at 0
[    0.149436] ACPI: Added _OSI(Module Device)
[    0.149474] ACPI: Added _OSI(Processor Device)
[    0.149512] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.149550] ACPI: Added _OSI(Processor Aggregator Device)
[    0.151396] ACPI: EC: Look up EC in DSDT
[    0.177882] ACPI: Executed 1 blocks of module-level executable AML code
[    0.183861] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
[    0.195624] ACPI: SSDT 00000000dae70718 00688 (v01  PmRef  Cpu0Cst 00003001 INTL 20061109)
[    0.196230] ACPI: Dynamic OEM Table Load:
[    0.196300] ACPI: SSDT           (null) 00688 (v01  PmRef  Cpu0Cst 00003001 INTL 20061109)
[    0.206316] ACPI: SSDT 00000000dae71a98 00303 (v01  PmRef    ApIst 00003000 INTL 20061109)
[    0.206999] ACPI: Dynamic OEM Table Load:
[    0.207069] ACPI: SSDT           (null) 00303 (v01  PmRef    ApIst 00003000 INTL 20061109)
[    0.218216] ACPI: SSDT 00000000dae6fd98 00119 (v01  PmRef    ApCst 00003000 INTL 20061109)
[    0.218791] ACPI: Dynamic OEM Table Load:
[    0.218860] ACPI: SSDT           (null) 00119 (v01  PmRef    ApCst 00003000 INTL 20061109)
[    0.232254] ACPI: Interpreter enabled
[    0.232304] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20130517/hwxface-571)
[    0.232413] ACPI: (supports S0 S1 S3 S4 S5)
[    0.232450] ACPI: Using IOAPIC for interrupt routing
[    0.232545] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.232770] ACPI: No dock devices found.
[    0.256432] ACPI: Power Resource [FN00] (off)
[    0.256653] ACPI: Power Resource [FN01] (off)
[    0.256870] ACPI: Power Resource [FN02] (off)
[    0.257089] ACPI: Power Resource [FN03] (off)
[    0.257310] ACPI: Power Resource [FN04] (off)
[    0.258500] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-3e])
[    0.258874] \_SB_.PCI0:_OSC invalid UUID
[    0.258875] _OSC request data:1 8 0 
[    0.259837] PCI host bridge to bus 0000:00
[    0.259877] pci_bus 0000:00: root bus resource [bus 00-3e]
[    0.259917] pci_bus 0000:00: root bus resource [io  0x0000-0x0cf7]
[    0.259957] pci_bus 0000:00: root bus resource [io  0x0d00-0xffff]
[    0.259998] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[    0.260040] pci_bus 0000:00: root bus resource [mem 0xdfa00000-0xfeafffff]
[    0.260082] pci_bus 0000:00: root bus resource [mem 0xfed40000-0xfed44fff]
[    0.260138] pci 0000:00:00.0: [8086:0104] type 00 class 0x060000
[    0.260293] pci 0000:00:02.0: [8086:0116] type 00 class 0x030000
[    0.260306] pci 0000:00:02.0: reg 0x10: [mem 0xf0000000-0xf03fffff 64bit]
[    0.260314] pci 0000:00:02.0: reg 0x18: [mem 0xe0000000-0xefffffff 64bit pref]
[    0.260319] pci 0000:00:02.0: reg 0x20: [io  0x3000-0x303f]
[    0.260512] pci 0000:00:16.0: [8086:1c3a] type 00 class 0x078000
[    0.260539] pci 0000:00:16.0: reg 0x10: [mem 0xf0705000-0xf070500f 64bit]
[    0.260625] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
[    0.260785] pci 0000:00:1a.0: [8086:1c2d] type 00 class 0x0c0320
[    0.260808] pci 0000:00:1a.0: reg 0x10: [mem 0xf070a000-0xf070a3ff]
[    0.260909] pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
[    0.261013] pci 0000:00:1b.0: [8086:1c20] type 00 class 0x040300
[    0.261033] pci 0000:00:1b.0: reg 0x10: [mem 0xf0700000-0xf0703fff 64bit]
[    0.261112] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[    0.261159] pci 0000:00:1b.0: System wakeup disabled by ACPI
[    0.261265] pci 0000:00:1c.0: [8086:1c10] type 01 class 0x060400
[    0.261356] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[    0.261404] pci 0000:00:1c.0: System wakeup disabled by ACPI
[    0.261513] pci 0000:00:1c.3: [8086:1c16] type 01 class 0x060400
[    0.261602] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
[    0.261660] pci 0000:00:1c.3: System wakeup disabled by ACPI
[    0.261765] pci 0000:00:1c.4: [8086:1c18] type 01 class 0x060400
[    0.261858] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
[    0.261986] pci 0000:00:1d.0: [8086:1c26] type 00 class 0x0c0320
[    0.262010] pci 0000:00:1d.0: reg 0x10: [mem 0xf0709000-0xf07093ff]
[    0.262116] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
[    0.262223] pci 0000:00:1f.0: [8086:1c49] type 00 class 0x060100
[    0.262420] pci 0000:00:1f.2: [8086:1c03] type 00 class 0x010601
[    0.262441] pci 0000:00:1f.2: reg 0x10: [io  0x3088-0x308f]
[    0.262451] pci 0000:00:1f.2: reg 0x14: [io  0x3094-0x3097]
[    0.262461] pci 0000:00:1f.2: reg 0x18: [io  0x3080-0x3087]
[    0.262471] pci 0000:00:1f.2: reg 0x1c: [io  0x3090-0x3093]
[    0.262481] pci 0000:00:1f.2: reg 0x20: [io  0x3060-0x307f]
[    0.262491] pci 0000:00:1f.2: reg 0x24: [mem 0xf0708000-0xf07087ff]
[    0.262544] pci 0000:00:1f.2: PME# supported from D3hot
[    0.262661] pci 0000:00:1f.3: [8086:1c22] type 00 class 0x0c0500
[    0.262679] pci 0000:00:1f.3: reg 0x10: [mem 0xf0704000-0xf07040ff 64bit]
[    0.262703] pci 0000:00:1f.3: reg 0x20: [io  0xefa0-0xefbf]
[    0.263074] pci 0000:01:00.0: [8086:0091] type 00 class 0x028000
[    0.263255] pci 0000:01:00.0: reg 0x10: [mem 0xf0600000-0xf0601fff 64bit]
[    0.263988] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[    0.264158] pci 0000:01:00.0: System wakeup disabled by ACPI
[    0.270168] pci 0000:00:1c.0: PCI bridge to [bus 01]
[    0.270212] pci 0000:00:1c.0:   bridge window [mem 0xf0600000-0xf06fffff]
[    0.270391] pci 0000:02:00.0: [10ec:8168] type 00 class 0x020000
[    0.270462] pci 0000:02:00.0: reg 0x10: [io  0x2000-0x20ff]
[    0.270585] pci 0000:02:00.0: reg 0x18: [mem 0xf0404000-0xf0404fff 64bit pref]
[    0.270661] pci 0000:02:00.0: reg 0x20: [mem 0xf0400000-0xf0403fff 64bit pref]
[    0.270993] pci 0000:02:00.0: supports D1 D2
[    0.270995] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.271117] pci 0000:02:00.0: System wakeup disabled by ACPI
[    0.278104] pci 0000:00:1c.3: PCI bridge to [bus 02]
[    0.278165] pci 0000:00:1c.3:   bridge window [io  0x2000-0x2fff]
[    0.278175] pci 0000:00:1c.3:   bridge window [mem 0xf0400000-0xf04fffff 64bit pref]
[    0.278297] pci 0000:03:00.0: [1b21:1042] type 00 class 0x0c0330
[    0.278335] pci 0000:03:00.0: reg 0x10: [mem 0xf0500000-0xf0507fff 64bit]
[    0.278533] pci 0000:03:00.0: PME# supported from D3hot D3cold
[    0.286076] pci 0000:00:1c.4: PCI bridge to [bus 03]
[    0.286152] pci 0000:00:1c.4:   bridge window [mem 0xf0500000-0xf05fffff]
[    0.286336] \_SB_.PCI0:_OSC invalid UUID
[    0.286338] _OSC request data:1 1f 0 
[    0.286342] acpi PNP0A08:00: ACPI _OSC support notification failed, disabling PCIe ASPM
[    0.286398] acpi PNP0A08:00: Unable to request _OSC control (_OSC support mask: 0x08)
[    0.287366] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 10 *11 12 14 15)
[    0.287716] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 10 11 12 14 15) *0, disabled.
[    0.288109] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 *10 11 12 14 15)
[    0.288455] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 *10 11 12 14 15)
[    0.288800] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 10 11 12 14 15) *9
[    0.289174] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 10 11 12 14 15) *0, disabled.
[    0.289567] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 10 *11 12 14 15)
[    0.289915] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 10 11 12 14 15) *9
[    0.290788] ACPI: Enabled 4 GPEs in block 00 to 3F
[    0.290866] ACPI: \_SB_.PCI0: notify handler is installed
[    0.290927] Found 1 acpi root devices
[    0.290997] ACPI: EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62
[    0.291351] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[    0.291409] vgaarb: loaded
[    0.291443] vgaarb: bridge control possible 0000:00:02.0
[    0.292155] SCSI subsystem initialized
[    0.292192] ACPI: bus type ATA registered
[    0.292326] libata version 3.00 loaded.
[    0.292389] ACPI: bus type USB registered
[    0.292469] usbcore: registered new interface driver usbfs
[    0.292530] usbcore: registered new interface driver hub
[    0.292624] usbcore: registered new device driver usb
[    0.292977] PCI: Using ACPI for IRQ routing
[    0.294688] PCI: pci_cache_line_size set to 64 bytes
[    0.294799] e820: reserve RAM buffer [mem 0x0009d800-0x0009ffff]
[    0.294802] e820: reserve RAM buffer [mem 0xd9c9f000-0xdbffffff]
[    0.294805] e820: reserve RAM buffer [mem 0xdb000000-0xdbffffff]
[    0.294807] e820: reserve RAM buffer [mem 0x11fe00000-0x11fffffff]
[    0.295084] NetLabel: Initializing
[    0.295120] NetLabel:  domain hash size = 128
[    0.295157] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.295240] NetLabel:  unlabeled traffic allowed by default
[    0.295366] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
[    0.295556] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
[    0.297618] Switched to clocksource hpet
[    0.315241] AppArmor: AppArmor Filesystem Enabled
[    0.315337] pnp: PnP ACPI init
[    0.315387] ACPI: bus type PNP registered
[    0.315774] pnp 00:00: [dma 4]
[    0.315815] pnp 00:00: Plug and Play ACPI device, IDs PNP0200 (active)
[    0.315861] pnp 00:01: Plug and Play ACPI device, IDs INT0800 (active)
[    0.316028] pnp 00:02: Plug and Play ACPI device, IDs PNP0103 (active)
[    0.316081] pnp 00:03: Plug and Play ACPI device, IDs PNP0c04 (active)
[    0.316162] system 00:04: [io  0x0680-0x069f] has been reserved
[    0.316204] system 00:04: [io  0x1000-0x100f] has been reserved
[    0.316244] system 00:04: [io  0x5000-0x5003] has been reserved
[    0.316285] system 00:04: [io  0xffff] has been reserved
[    0.316325] system 00:04: [io  0x0400-0x0453] could not be reserved
[    0.316366] system 00:04: [io  0x0458-0x047f] has been reserved
[    0.316406] system 00:04: [io  0x0500-0x057f] has been reserved
[    0.316446] system 00:04: [io  0x0a00-0x0a0f] has been reserved
[    0.316487] system 00:04: [io  0x164e-0x164f] has been reserved
[    0.316528] system 00:04: [io  0x5000-0x500f] could not be reserved
[    0.316570] system 00:04: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.316620] pnp 00:05: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.316715] system 00:06: [io  0x0454-0x0457] has been reserved
[    0.316757] system 00:06: Plug and Play ACPI device, IDs INT3f0d PNP0c02 (active)
[    0.316817] pnp 00:07: Plug and Play ACPI device, IDs PNP0303 (active)
[    0.316901] pnp 00:08: Plug and Play ACPI device, IDs ETD0b00 SYN0002 PNP0f13 (active)
[    0.317209] system 00:09: [mem 0xfed1c000-0xfed1ffff] has been reserved
[    0.317252] system 00:09: [mem 0xfed10000-0xfed17fff] has been reserved
[    0.317294] system 00:09: [mem 0xfed18000-0xfed18fff] has been reserved
[    0.317335] system 00:09: [mem 0xfed19000-0xfed19fff] has been reserved
[    0.317377] system 00:09: [mem 0xf8000000-0xfbffffff] has been reserved
[    0.317419] system 00:09: [mem 0xfed20000-0xfed3ffff] has been reserved
[    0.317461] system 00:09: [mem 0xfed90000-0xfed93fff] has been reserved
[    0.317503] system 00:09: [mem 0xfed45000-0xfed8ffff] has been reserved
[    0.317545] system 00:09: [mem 0xff000000-0xffffffff] could not be reserved
[    0.317587] system 00:09: [mem 0xfee00000-0xfeefffff] could not be reserved
[    0.317641] system 00:09: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.318359] system 00:0a: Plug and Play ACPI device, IDs PNP0c01 (active)
[    0.318397] pnp: PnP ACPI: found 11 devices
[    0.318434] ACPI: bus type PNP unregistered
[    0.326516] pci 0000:00:1c.0: PCI bridge to [bus 01]
[    0.326561] pci 0000:00:1c.0:   bridge window [mem 0xf0600000-0xf06fffff]
[    0.326612] pci 0000:00:1c.3: PCI bridge to [bus 02]
[    0.326652] pci 0000:00:1c.3:   bridge window [io  0x2000-0x2fff]
[    0.326700] pci 0000:00:1c.3:   bridge window [mem 0xf0400000-0xf04fffff 64bit pref]
[    0.326761] pci 0000:00:1c.4: PCI bridge to [bus 03]
[    0.326804] pci 0000:00:1c.4:   bridge window [mem 0xf0500000-0xf05fffff]
[    0.327276] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7]
[    0.327278] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff]
[    0.327280] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[    0.327282] pci_bus 0000:00: resource 7 [mem 0xdfa00000-0xfeafffff]
[    0.327284] pci_bus 0000:00: resource 8 [mem 0xfed40000-0xfed44fff]
[    0.327287] pci_bus 0000:01: resource 1 [mem 0xf0600000-0xf06fffff]
[    0.327289] pci_bus 0000:02: resource 0 [io  0x2000-0x2fff]
[    0.327291] pci_bus 0000:02: resource 2 [mem 0xf0400000-0xf04fffff 64bit pref]
[    0.327293] pci_bus 0000:03: resource 1 [mem 0xf0500000-0xf05fffff]
[    0.327430] NET: Registered protocol family 2
[    0.327837] TCP established hash table entries: 32768 (order: 7, 524288 bytes)
[    0.328072] TCP bind hash table entries: 32768 (order: 8, 1048576 bytes)
[    0.328397] TCP: Hash tables configured (established 32768 bind 32768)
[    0.328696] TCP: reno registered
[    0.328749] UDP hash table entries: 2048 (order: 5, 196608 bytes)
[    0.328854] UDP-Lite hash table entries: 2048 (order: 5, 196608 bytes)
[    0.329147] NET: Registered protocol family 1
[    0.329202] pci 0000:00:02.0: Boot video device
[    0.329998] PCI: CLS 64 bytes, default 64
[    0.330209] Trying to unpack rootfs image as initramfs...
[    0.406522] Freeing initrd memory: 3348K (ffff880037966000 - ffff880037cab000)
[    0.406583] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[    0.406625] software IO TLB [mem 0xd5c9f000-0xd9c9f000] (64MB) mapped at [ffff8800d5c9f000-ffff8800d9c9efff]
[    0.406932] perf: amd_iommu PMU not installed. No support!
[    0.407094] microcode: CPU0 sig=0x206a7, pf=0x10, revision=0x28
[    0.407141] microcode: CPU1 sig=0x206a7, pf=0x10, revision=0x28
[    0.407192] microcode: CPU2 sig=0x206a7, pf=0x10, revision=0x28
[    0.407241] microcode: CPU3 sig=0x206a7, pf=0x10, revision=0x28
[    0.407367] microcode: Microcode Update Driver: v2.00 <tigran@xxxxxxxxxxxxxxxxxxxx>, Peter Oruba
[    0.407424] Scanning for low memory corruption every 60 seconds
[    0.408065] Initialise module verification
[    0.408164] audit: initializing netlink socket (disabled)
[    0.408224] type=2000 audit(1372413692.392:1): initialized
[    0.438081] bounce pool size: 64 pages
[    0.438142] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    0.439369] VFS: Disk quotas dquot_6.5.2
[    0.439448] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.440322] fuse init (API version 7.22)
[    0.440462] msgmni has been set to 7698
[    0.441221] Key type asymmetric registered
[    0.441259] Asymmetric key parser 'x509' registered
[    0.441346] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    0.441457] io scheduler noop registered
[    0.441494] io scheduler deadline registered (default)
[    0.441627] io scheduler cfq registered
[    0.442047] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    0.442128] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    0.442261] intel_idle: MWAIT substates: 0x21120
[    0.442263] intel_idle: v0.4 model 0x2A
[    0.442264] intel_idle: lapic_timer_reliable_states 0xffffffff
[    0.442733] ACPI: AC Adapter [ADP1] (on-line)
[    0.443208] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input0
[    0.443284] ACPI: Lid Switch [LID0]
[    0.443385] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[    0.443444] ACPI: Power Button [PWRB]
[    0.443540] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[    0.443596] ACPI: Power Button [PWRF]
[    0.443724] ACPI: Fan [FAN0] (off)
[    0.443808] ACPI: Fan [FAN1] (off)
[    0.443899] ACPI: Fan [FAN2] (off)
[    0.443983] ACPI: Fan [FAN3] (off)
[    0.444068] ACPI: Fan [FAN4] (off)
[    0.444185] ACPI: Requesting acpi_cpufreq
[    0.447529] thermal LNXTHERM:00: registered as thermal_zone0
[    0.447570] ACPI: Thermal Zone [TZ00] (67 C)
[    0.448027] thermal LNXTHERM:01: registered as thermal_zone1
[    0.448067] ACPI: Thermal Zone [TZ01] (30 C)
[    0.448162] GHES: HEST is not enabled!
[    0.448420] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[    0.453610] ACPI: Battery Slot [BAT1] (battery present)
[    0.453628] Linux agpgart interface v0.103
[    0.456185] brd: module loaded
[    0.457622] loop: module loaded
[    0.457887] mei_me 0000:00:16.0: setting latency timer to 64
[    0.457934] mei_me 0000:00:16.0: irq 40 for MSI/MSI-X
[    0.461035] ahci 0000:00:1f.2: version 3.0
[    0.461224] ahci 0000:00:1f.2: irq 41 for MSI/MSI-X
[    0.461433] ahci: SSS flag set, parallel bus scan disabled
[    0.473536] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 6 Gbps 0x1b impl SATA mode
[    0.473594] ahci 0000:00:1f.2: flags: 64bit ncq sntf ilck stag pm led clo pio slum part ems sxs apst 
[    0.473655] ahci 0000:00:1f.2: setting latency timer to 64
[    0.498337] scsi0 : ahci
[    0.498580] scsi1 : ahci
[    0.498734] scsi2 : ahci
[    0.498894] scsi3 : ahci
[    0.499052] scsi4 : ahci
[    0.499209] scsi5 : ahci
[    0.499319] ata1: SATA max UDMA/133 abar m2048@0xf0708000 port 0xf0708100 irq 41
[    0.499374] ata2: SATA max UDMA/133 abar m2048@0xf0708000 port 0xf0708180 irq 41
[    0.499428] ata3: DUMMY
[    0.499461] ata4: SATA max UDMA/133 abar m2048@0xf0708000 port 0xf0708280 irq 41
[    0.499516] ata5: SATA max UDMA/133 abar m2048@0xf0708000 port 0xf0708300 irq 41
[    0.499569] ata6: DUMMY
[    0.500459] libphy: Fixed MDIO Bus: probed
[    0.500772] tun: Universal TUN/TAP device driver, 1.6
[    0.500809] tun: (C) 1999-2004 Max Krasnyansky <maxk@xxxxxxxxxxxx>
[    0.500935] PPP generic driver version 2.4.2
[    0.501084] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.501125] ehci_hcd: block sizes: qh 112 qtd 96 itd 192 sitd 96
[    0.501136] ehci-pci: EHCI PCI platform driver
[    0.501353] ehci-pci 0000:00:1a.0: setting latency timer to 64
[    0.501363] ehci-pci 0000:00:1a.0: EHCI Host Controller
[    0.501408] ehci-pci 0000:00:1a.0: new USB bus registered, assigned bus number 1
[    0.501489] ehci-pci 0000:00:1a.0: debug port 2
[    0.501529] ehci-pci 0000:00:1a.0: reset hcs_params 0x200002 dbg=2 cc=0 pcc=0 ordered !ppc ports=2
[    0.501533] ehci-pci 0000:00:1a.0: reset hcc_params 36881 caching frame 1024 64 bit addr
[    0.501572] ehci-pci 0000:00:1a.0: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT
[    0.505447] ehci-pci 0000:00:1a.0: cache line size of 64 is not supported
[    0.505449] ehci-pci 0000:00:1a.0: supports USB remote wakeup
[    0.505503] ehci-pci 0000:00:1a.0: irq 16, io mem 0xf070a000
[    0.505546] ehci-pci 0000:00:1a.0: init command 0010001 (park)=0 ithresh=1 period=1024 RUN
[    0.517478] ehci-pci 0000:00:1a.0: USB 2.0 started, EHCI 1.00
[    0.517552] usb usb1: default language 0x0409
[    0.517565] usb usb1: udev 1, busnum 1, minor = 0
[    0.517567] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    0.517608] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.517662] usb usb1: Product: EHCI Host Controller
[    0.517700] usb usb1: Manufacturer: Linux 3.10.0-rc7-next20130628-1-iniza-small ehci_hcd
[    0.517755] usb usb1: SerialNumber: 0000:00:1a.0
[    0.517921] usb usb1: usb_probe_device
[    0.517924] usb usb1: configuration #1 chosen from 1 choice
[    0.517934] usb usb1: adding 1-0:1.0 (config #1, interface 0)
[    0.517967] hub 1-0:1.0: usb_probe_interface
[    0.517969] hub 1-0:1.0: usb_probe_interface - got id
[    0.517972] hub 1-0:1.0: USB hub found
[    0.518016] hub 1-0:1.0: 2 ports detected
[    0.518052] hub 1-0:1.0: standalone hub
[    0.518054] hub 1-0:1.0: no power switching (usb 1.0)
[    0.518055] hub 1-0:1.0: individual port over-current protection
[    0.518057] hub 1-0:1.0: power on to power good time: 20ms
[    0.518063] hub 1-0:1.0: local power source is good
[    0.518117] hub 1-0:1.0: trying to enable port power on non-switchable hub
[    0.518341] ehci-pci 0000:00:1d.0: setting latency timer to 64
[    0.518348] ehci-pci 0000:00:1d.0: EHCI Host Controller
[    0.518394] ehci-pci 0000:00:1d.0: new USB bus registered, assigned bus number 2
[    0.518464] ehci-pci 0000:00:1d.0: debug port 2
[    0.518504] ehci-pci 0000:00:1d.0: reset hcs_params 0x200002 dbg=2 cc=0 pcc=0 ordered !ppc ports=2
[    0.518507] ehci-pci 0000:00:1d.0: reset hcc_params 36881 caching frame 1024 64 bit addr
[    0.518542] ehci-pci 0000:00:1d.0: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT
[    0.522434] ehci-pci 0000:00:1d.0: cache line size of 64 is not supported
[    0.522436] ehci-pci 0000:00:1d.0: supports USB remote wakeup
[    0.522481] ehci-pci 0000:00:1d.0: irq 23, io mem 0xf0709000
[    0.522523] ehci-pci 0000:00:1d.0: init command 0010001 (park)=0 ithresh=1 period=1024 RUN
[    0.533465] ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[    0.533537] usb usb2: default language 0x0409
[    0.533549] usb usb2: udev 1, busnum 2, minor = 128
[    0.533551] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[    0.533592] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.533646] usb usb2: Product: EHCI Host Controller
[    0.533684] usb usb2: Manufacturer: Linux 3.10.0-rc7-next20130628-1-iniza-small ehci_hcd
[    0.533738] usb usb2: SerialNumber: 0000:00:1d.0
[    0.533886] usb usb2: usb_probe_device
[    0.533888] usb usb2: configuration #1 chosen from 1 choice
[    0.533898] usb usb2: adding 2-0:1.0 (config #1, interface 0)
[    0.533929] hub 2-0:1.0: usb_probe_interface
[    0.533931] hub 2-0:1.0: usb_probe_interface - got id
[    0.533934] hub 2-0:1.0: USB hub found
[    0.533975] hub 2-0:1.0: 2 ports detected
[    0.534011] hub 2-0:1.0: standalone hub
[    0.534012] hub 2-0:1.0: no power switching (usb 1.0)
[    0.534014] hub 2-0:1.0: individual port over-current protection
[    0.534016] hub 2-0:1.0: power on to power good time: 20ms
[    0.534021] hub 2-0:1.0: local power source is good
[    0.534075] hub 2-0:1.0: trying to enable port power on non-switchable hub
[    0.534148] ehci-platform: EHCI generic platform driver
[    0.534202] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    0.534242] ohci_hcd: block sizes: ed 80 td 96
[    0.534248] ohci-pci: OHCI PCI platform driver
[    0.534302] ohci-platform: OHCI generic platform driver
[    0.534357] uhci_hcd: USB Universal Host Controller Interface driver
[    0.534600] xhci_hcd 0000:03:00.0: xHCI Host Controller
[    0.534645] xhci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 3
[    0.544412] xhci_hcd 0000:03:00.0: supports USB remote wakeup
[    0.544445] xhci_hcd 0000:03:00.0: irq 42 for MSI/MSI-X
[    0.544453] xhci_hcd 0000:03:00.0: irq 43 for MSI/MSI-X
[    0.544461] xhci_hcd 0000:03:00.0: irq 44 for MSI/MSI-X
[    0.544468] xhci_hcd 0000:03:00.0: irq 45 for MSI/MSI-X
[    0.544477] xhci_hcd 0000:03:00.0: irq 46 for MSI/MSI-X
[    0.544746] usb usb3: default language 0x0409
[    0.544758] usb usb3: udev 1, busnum 3, minor = 256
[    0.544760] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[    0.544802] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.544855] usb usb3: Product: xHCI Host Controller
[    0.544893] usb usb3: Manufacturer: Linux 3.10.0-rc7-next20130628-1-iniza-small xhci_hcd
[    0.544948] usb usb3: SerialNumber: 0000:03:00.0
[    0.545132] usb usb3: usb_probe_device
[    0.545135] usb usb3: configuration #1 chosen from 1 choice
[    0.545139] xHCI xhci_add_endpoint called for root hub
[    0.545141] xHCI xhci_check_bandwidth called for root hub
[    0.545149] usb usb3: adding 3-0:1.0 (config #1, interface 0)
[    0.545181] hub 3-0:1.0: usb_probe_interface
[    0.545182] hub 3-0:1.0: usb_probe_interface - got id
[    0.545185] hub 3-0:1.0: USB hub found
[    0.545231] hub 3-0:1.0: 2 ports detected
[    0.545267] hub 3-0:1.0: standalone hub
[    0.545269] hub 3-0:1.0: no power switching (usb 1.0)
[    0.545270] hub 3-0:1.0: individual port over-current protection
[    0.545272] hub 3-0:1.0: Single TT
[    0.545274] hub 3-0:1.0: TT requires at most 8 FS bit times (666 ns)
[    0.545275] hub 3-0:1.0: power on to power good time: 20ms
[    0.545280] hub 3-0:1.0: local power source is good
[    0.545320] hub 3-0:1.0: trying to enable port power on non-switchable hub
[    0.545386] xhci_hcd 0000:03:00.0: xHCI Host Controller
[    0.545429] xhci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 4
[    0.545506] xhci_hcd 0000:03:00.0: supports USB remote wakeup
[    0.545541] usb usb4: skipped 1 descriptor after endpoint
[    0.545546] usb usb4: default language 0x0409
[    0.545557] usb usb4: udev 1, busnum 4, minor = 384
[    0.545559] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003
[    0.545600] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.545654] usb usb4: Product: xHCI Host Controller
[    0.545691] usb usb4: Manufacturer: Linux 3.10.0-rc7-next20130628-1-iniza-small xhci_hcd
[    0.545747] usb usb4: SerialNumber: 0000:03:00.0
[    0.545881] usb usb4: usb_probe_device
[    0.545883] usb usb4: configuration #1 chosen from 1 choice
[    0.545889] xHCI xhci_add_endpoint called for root hub
[    0.545890] xHCI xhci_check_bandwidth called for root hub
[    0.545896] usb usb4: adding 4-0:1.0 (config #1, interface 0)
[    0.545927] hub 4-0:1.0: usb_probe_interface
[    0.545929] hub 4-0:1.0: usb_probe_interface - got id
[    0.545931] hub 4-0:1.0: USB hub found
[    0.545976] hub 4-0:1.0: 2 ports detected
[    0.546013] hub 4-0:1.0: standalone hub
[    0.546014] hub 4-0:1.0: no power switching (usb 1.0)
[    0.546016] hub 4-0:1.0: individual port over-current protection
[    0.546017] hub 4-0:1.0: TT requires at most 8 FS bit times (666 ns)
[    0.546019] hub 4-0:1.0: power on to power good time: 20ms
[    0.546024] hub 4-0:1.0: local power source is good
[    0.546057] hub 4-0:1.0: trying to enable port power on non-switchable hub
[    0.557522] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:EPAD] at 0x60,0x64 irq 1,12
[    0.563770] serio: i8042 KBD port at 0x60,0x64 irq 1
[    0.563812] serio: i8042 AUX port at 0x60,0x64 irq 12
[    0.564074] mousedev: PS/2 mouse device common for all mice
[    0.564578] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
[    0.564651] rtc_cmos 00:05: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
[    0.564769] device-mapper: uevent: version 1.0.3
[    0.564906] device-mapper: ioctl: 4.25.0-ioctl (2013-06-26) initialised: dm-devel@xxxxxxxxxx
[    0.564978] Intel P-state driver initializing.
[    0.565027] Intel pstate controlling: cpu 0
[    0.565087] Intel pstate controlling: cpu 1
[    0.565145] Intel pstate controlling: cpu 2
[    0.565198] Intel pstate controlling: cpu 3
[    0.565484] cpuidle: using governor ladder
[    0.565757] cpuidle: using governor menu
[    0.565801] ledtrig-cpu: registered to indicate activity on CPUs
[    0.566083] ashmem: initialized
[    0.566286] TCP: cubic registered
[    0.566493] NET: Registered protocol family 10
[    0.567012] NET: Registered protocol family 17
[    0.567071] Key type dns_resolver registered
[    0.567643] PM: Hibernation image not present or could not be loaded.
[    0.567649] Loading module verification certificates
[    0.569060] MODSIGN: Loaded cert 'Magrathea: Glacier signing key: 09f5fba84f221d8c430ece4e95f27a78e257c35f'
[    0.569160] registered taskstats version 1
[    0.573107] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
[    0.573194] Key type trusted registered
[    0.580557] Key type encrypted registered
[    0.587746] rtc_cmos 00:05: setting system clock to 2013-06-28 10:01:33 UTC (1372413693)
[    0.588181] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    0.588222] EDD information not available.
[    0.617542] ehci-pci 0000:00:1a.0: GetStatus port:1 status 001803 0  ACK POWER sig=j CSC CONNECT
[    0.617552] hub 1-0:1.0: port 1: status 0501 change 0001
[    0.633517] ehci-pci 0000:00:1d.0: GetStatus port:1 status 001803 0  ACK POWER sig=j CSC CONNECT
[    0.633528] hub 2-0:1.0: port 1: status 0501 change 0001
[    0.641537] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[    0.641851] hub 3-0:1.0: hub_suspend
[    0.641864] usb usb3: bus auto-suspend, wakeup 1
[    0.645540] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000
[    0.645597] hub 4-0:1.0: hub_suspend
[    0.645607] usb usb4: bus auto-suspend, wakeup 1
[    0.654100] usb usb4: usb wakeup-resume
[    0.654114] usb usb4: usb auto-resume
[    0.665483] hub 4-0:1.0: hub_resume
[    0.665507] hub 4-0:1.0: port 1: status 0203 change 0001
[    0.717482] hub 1-0:1.0: state 7 ports 2 chg 0002 evt 0000
[    0.717517] hub 1-0:1.0: port 1, status 0501, change 0000, 480 Mb/s
[    0.773634] ehci-pci 0000:00:1a.0: port 1 reset complete, port enabled
[    0.773642] ehci-pci 0000:00:1a.0: GetStatus port:1 status 001005 0  ACK POWER sig=se0 PE CONNECT
[    0.817390] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    0.818629] ata1.00: ATA-8: Hitachi HTS545050A7E380, GG2OA6C0, max UDMA/133
[    0.818684] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[    0.820097] ata1.00: configured for UDMA/133
[    0.820496] scsi 0:0:0:0: Direct-Access     ATA      Hitachi HTS54505 GG2O PQ: 0 ANSI: 5
[    0.820946] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
[    0.821020] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    0.821093] sd 0:0:0:0: [sda] 4096-byte physical blocks
[    0.821405] sd 0:0:0:0: [sda] Write Protect is off
[    0.821456] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    0.821644] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    0.829333] usb 1-1: new high-speed USB device number 2 using ehci-pci
[    0.836231]  sda: sda1 sda2 sda3
[    0.837614] sd 0:0:0:0: [sda] Attached SCSI disk
[    0.885555] ehci-pci 0000:00:1a.0: port 1 reset complete, port enabled
[    0.885565] ehci-pci 0000:00:1a.0: GetStatus port:1 status 001005 0  ACK POWER sig=se0 PE CONNECT
[    0.961995] usb 1-1: udev 2, busnum 1, minor = 1
[    0.962004] usb 1-1: New USB device found, idVendor=8087, idProduct=0024
[    0.962059] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    0.962438] usb 1-1: usb_probe_device
[    0.962445] usb 1-1: configuration #1 chosen from 1 choice
[    0.962569] usb 1-1: adding 1-1:1.0 (config #1, interface 0)
[    0.962623] hub 1-1:1.0: usb_probe_interface
[    0.962627] hub 1-1:1.0: usb_probe_interface - got id
[    0.962632] hub 1-1:1.0: USB hub found
[    0.963336] hub 1-1:1.0: 6 ports detected
[    0.963387] hub 1-1:1.0: standalone hub
[    0.963390] hub 1-1:1.0: individual port power switching
[    0.963393] hub 1-1:1.0: individual port over-current protection
[    0.963395] hub 1-1:1.0: Single TT
[    0.963398] hub 1-1:1.0: TT requires at most 8 FS bit times (666 ns)
[    0.963401] hub 1-1:1.0: power on to power good time: 100ms
[    0.963861] hub 1-1:1.0: local power source is good
[    0.964181] hub 1-1:1.0: enabling power on all ports
[    0.965009] hub 2-0:1.0: state 7 ports 2 chg 0002 evt 0000
[    0.965024] hub 2-0:1.0: port 1, status 0501, change 0000, 480 Mb/s
[    1.017462] ehci-pci 0000:00:1d.0: port 1 reset complete, port enabled
[    1.017472] ehci-pci 0000:00:1d.0: GetStatus port:1 status 001005 0  ACK POWER sig=se0 PE CONNECT
[    1.061646] hub 1-1:1.0: port 2: status 0101 change 0001
[    1.062148] hub 1-1:1.0: port 4: status 0101 change 0001
[    1.073221] usb 2-1: new high-speed USB device number 2 using ehci-pci
[    1.129384] ehci-pci 0000:00:1d.0: port 1 reset complete, port enabled
[    1.129396] ehci-pci 0000:00:1d.0: GetStatus port:1 status 001005 0  ACK POWER sig=se0 PE CONNECT
[    1.137149] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    1.137763] ata2.00: ATA-8: SanDisk iSSD P4 16GB, SSD 9.14, max UDMA/133
[    1.137828] ata2.00: 31277232 sectors, multi 1: LBA48 
[    1.138571] ata2.00: configured for UDMA/133
[    1.139054] scsi 1:0:0:0: Direct-Access     ATA      SanDisk iSSD P4  SSD  PQ: 0 ANSI: 5
[    1.139443] sd 1:0:0:0: [sdb] 31277232 512-byte logical blocks: (16.0 GB/14.9 GiB)
[    1.139482] sd 1:0:0:0: Attached scsi generic sg1 type 0
[    1.139725] sd 1:0:0:0: [sdb] Write Protect is off
[    1.139783] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[    1.139827] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.141060]  sdb: sdb1 sdb2
[    1.141792] sd 1:0:0:0: [sdb] Attached SCSI disk
[    1.161147] usb 1-1: link qh256-0001/ffff880118696ec0 start 1 [1/0 us]
[    1.205825] usb 2-1: udev 2, busnum 2, minor = 129
[    1.205833] usb 2-1: New USB device found, idVendor=8087, idProduct=0024
[    1.205895] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    1.206244] usb 2-1: usb_probe_device
[    1.206251] usb 2-1: configuration #1 chosen from 1 choice
[    1.206428] usb 2-1: adding 2-1:1.0 (config #1, interface 0)
[    1.206497] hub 2-1:1.0: usb_probe_interface
[    1.206501] hub 2-1:1.0: usb_probe_interface - got id
[    1.206506] hub 2-1:1.0: USB hub found
[    1.206795] hub 2-1:1.0: 6 ports detected
[    1.206852] hub 2-1:1.0: standalone hub
[    1.206856] hub 2-1:1.0: individual port power switching
[    1.206859] hub 2-1:1.0: individual port over-current protection
[    1.206861] hub 2-1:1.0: Single TT
[    1.206865] hub 2-1:1.0: TT requires at most 8 FS bit times (666 ns)
[    1.206868] hub 2-1:1.0: power on to power good time: 100ms
[    1.207314] hub 2-1:1.0: local power source is good
[    1.207653] hub 2-1:1.0: enabling power on all ports
[    1.208680] hub 4-0:1.0: state 7 ports 2 chg 0002 evt 0000
[    1.208705] hub 4-0:1.0: port 1, status 0203, change 0000, 5.0 Gb/s
[    1.306228] hub 2-1:1.0: port 5: status 0101 change 0001
[    1.320610] usb 4-1: new SuperSpeed USB device number 2 using xhci_hcd
[    1.333599] usb 4-1: Parent hub missing LPM exit latency info.  Power management will be impacted.
[    1.334001] usb 4-1: skipped 1 descriptor after endpoint
[    1.334006] usb 4-1: skipped 1 descriptor after endpoint
[    1.334142] usb 4-1: default language 0x0409
[    1.334485] usb 4-1: udev 2, busnum 4, minor = 385
[    1.334493] usb 4-1: New USB device found, idVendor=174c, idProduct=55aa
[    1.334553] usb 4-1: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[    1.334602] usb 4-1: Product: MEDION HDDrive-n-GO
[    1.334646] usb 4-1: Manufacturer: MEDION
[    1.334689] usb 4-1: SerialNumber: 3180000000000000092C
[    1.334952] usb 4-1: usb_probe_device
[    1.334956] usb 4-1: configuration #1 chosen from 1 choice
[    1.335944] usb 4-1: Successful Endpoint Configure command
[    1.336056] usb 4-1: adding 4-1:1.0 (config #1, interface 0)
[    1.336209] hub 1-1:1.0: state 7 ports 6 chg 0014 evt 0000
[    1.336427] hub 1-1:1.0: port 2, status 0101, change 0000, 12 Mb/s
[    1.404962] tsc: Refined TSC clocksource calibration: 1596.373 MHz
[    1.405096] usb 2-1: link qh256-0001/ffff880118696bc0 start 1 [1/0 us]
[    1.405140] usb 1-1.2: new low-speed USB device number 3 using ehci-pci
[    1.456936] ata4: SATA link down (SStatus 0 SControl 300)
[    1.500119] usb 1-1.2: skipped 1 descriptor after interface
[    1.500593] usb 1-1.2: default language 0x0409
[    1.503261] usb 1-1.2: udev 3, busnum 1, minor = 2
[    1.503270] usb 1-1.2: New USB device found, idVendor=046d, idProduct=c00e
[    1.503324] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    1.503391] usb 1-1.2: Product: USB-PS/2 Optical Mouse
[    1.503438] usb 1-1.2: Manufacturer: Logitech
[    1.503766] usb 1-1.2: usb_probe_device
[    1.503773] usb 1-1.2: configuration #1 chosen from 1 choice
[    1.504378] usb 1-1.2: adding 1-1.2:1.0 (config #1, interface 0)
[    1.504648] hub 1-1:1.0: port 4, status 0101, change 0000, 12 Mb/s
[    1.573043] usb 1-1.4: new high-speed USB device number 4 using ehci-pci
[    1.776694] ata5: SATA link down (SStatus 0 SControl 300)
[    1.779332] Freeing unused kernel memory: 1332K (ffffffff81d06000 - ffffffff81e53000)
[    1.779415] Write protecting the kernel read-only data: 12288k
[    1.783156] Freeing unused kernel memory: 1076K (ffff8800016f3000 - ffff880001800000)
[    1.785954] Freeing unused kernel memory: 972K (ffff880001b0d000 - ffff880001c00000)
[    1.810110] udevd[123]: starting version 175
[    1.810552] usb 1-1.4: skipped 1 descriptor after configuration
[    1.810558] usb 1-1.4: skipped 5 descriptors after interface
[    1.810564] usb 1-1.4: skipped 1 descriptor after endpoint
[    1.810567] usb 1-1.4: skipped 23 descriptors after interface
[    1.812658] usb 1-1.4: default language 0x0409
[    1.824528] usb 1-1.4: udev 4, busnum 1, minor = 3
[    1.824555] usb 1-1.4: New USB device found, idVendor=2232, idProduct=1018
[    1.824605] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    1.824664] usb 1-1.4: Product: WebCam SC-13HDL11431N
[    1.824705] usb 1-1.4: Manufacturer: 123
[    1.824945] usb 1-1.4: usb_probe_device
[    1.824950] usb 1-1.4: configuration #1 chosen from 1 choice
[    1.825147] usb 1-1.4: adding 1-1.4:1.0 (config #1, interface 0)
[    1.951603] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[    1.951694] r8169 0000:02:00.0: can't disable ASPM; OS doesn't have ASPM control
[    1.952077] r8169 0000:02:00.0: irq 47 for MSI/MSI-X
[    1.957293] r8169 0000:02:00.0 eth0: RTL8168evl/8111evl at 0xffffc90000620000, e8:03:9a:36:17:a9, XID 0c900800 IRQ 47
[    1.957363] r8169 0000:02:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
[    1.960317] usb-storage 4-1:1.0: usb_probe_interface
[    1.960329] usb-storage 4-1:1.0: usb_probe_interface - got id
[    1.960335] usb-storage 4-1:1.0: USB Mass Storage device detected
[    1.960777] scsi6 : usb-storage 4-1:1.0
[    1.961009] usbcore: registered new interface driver usb-storage
[    1.997142] usb 1-1.4: adding 1-1.4:1.1 (config #1, interface 1)
[    1.997311] hub 2-1:1.0: state 7 ports 6 chg 0020 evt 0000
[    1.997398] hub 2-1:1.0: port 5, status 0101, change 0000, 12 Mb/s
[    2.015649] hidraw: raw HID events driver (C) Jiri Kosina
[    2.019724] usbhid 1-1.2:1.0: usb_probe_interface
[    2.019729] usbhid 1-1.2:1.0: usb_probe_interface - got id
[    2.022289] usbcore: registered new interface driver usbhid
[    2.022335] usbhid: USB HID core driver
[    2.026819] input: Logitech USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2:1.0/input/input4
[    2.027195] hid-generic 0003:046D:C00E.0001: input,hidraw0: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1a.0-1.2/input0
[    2.068705] usb 2-1.5: new full-speed USB device number 3 using ehci-pci
[    2.165053] usb 2-1.5: udev 3, busnum 2, minor = 130
[    2.165070] usb 2-1.5: New USB device found, idVendor=8086, idProduct=0189
[    2.165124] usb 2-1.5: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    2.165399] usb 2-1.5: usb_probe_device
[    2.165403] usb 2-1.5: configuration #1 chosen from 1 choice
[    2.165906] usb 2-1.5: adding 2-1.5:1.0 (config #1, interface 0)
[    2.166068] usb 2-1.5: adding 2-1.5:1.1 (config #1, interface 1)
[    2.166207] hub 1-1:1.0: state 7 ports 6 chg 0000 evt 0010
[    2.166276] hub 2-1:1.0: state 7 ports 6 chg 0000 evt 0020
[    2.754114] EXT4-fs (loop0): mounted filesystem with ordered data mode. Opts: (null)
[    2.960345] scsi 6:0:0:0: Direct-Access     ASMT     2105             0    PQ: 0 ANSI: 6
[    2.960888] sd 6:0:0:0: Attached scsi generic sg2 type 0
[    2.960992] sd 6:0:0:0: [sdc] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[    2.961474] sd 6:0:0:0: [sdc] Write Protect is off
[    2.961514] sd 6:0:0:0: [sdc] Mode Sense: 43 00 00 00
[    2.961933] sd 6:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    2.964413]  sdc: sdc1 sdc2 sdc3
[    2.966552] sd 6:0:0:0: [sdc] Attached SCSI disk
[    4.650411] init: ureadahead main process (335) terminated with status 5
[    8.096910] Adding 262140k swap on /host/ubuntu/disks/swap.disk.  Priority:-1 extents:1 across:262140k FS
[    8.222140] EXT4-fs (loop0): re-mounted. Opts: errors=remount-ro
[    8.367639] udevd[614]: starting version 175
[    9.376252] lp: driver loaded but no devices found
[   11.014353] wmi: Mapper loaded
[   11.097197] [drm] Initialized drm 1.1.0 20060810
[   11.103459] ACPI Warning: 0x0000000000000428-0x000000000000042f SystemIO conflicts with Region \PMIO 1 (20130517/utaddress-251)
[   11.103471] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   11.103478] ACPI Warning: 0x0000000000000540-0x000000000000054f SystemIO conflicts with Region \GPIO 1 (20130517/utaddress-251)
[   11.103484] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   11.103488] ACPI Warning: 0x0000000000000530-0x000000000000053f SystemIO conflicts with Region \GPIO 1 (20130517/utaddress-251)
[   11.103493] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   11.103496] ACPI Warning: 0x0000000000000500-0x000000000000052f SystemIO conflicts with Region \GPIO 1 (20130517/utaddress-251)
[   11.103500] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   11.103503] lpc_ich: Resource conflict(s) found affecting gpio_ich
[   11.204328] samsung_laptop: detected SABI interface: SwSmi@
[   11.204333] samsung_laptop: Backlight controlled by ACPI video driver
[   11.268522] cfg80211: Calling CRDA to update world regulatory domain
[   11.331043] Bluetooth: Core ver 2.16
[   11.331082] NET: Registered protocol family 31
[   11.331085] Bluetooth: HCI device and connection manager initialized
[   11.331102] Bluetooth: HCI socket layer initialized
[   11.331113] Bluetooth: L2CAP socket layer initialized
[   11.331130] Bluetooth: SCO socket layer initialized
[   11.551097] btusb 2-1.5:1.0: usb_probe_interface
[   11.551105] btusb 2-1.5:1.0: usb_probe_interface - got id
[   11.552425] usbcore: registered new interface driver btusb
[   11.552856] usb 2-1.5: link qh1-0e01/ffff880116c585c0 start 0 [1/2 us]
[   11.748585] Intel(R) Wireless WiFi driver for Linux, in-tree:d
[   11.748589] Copyright(c) 2003-2013 Intel Corporation
[   11.748649] iwlwifi 0000:01:00.0: can't disable ASPM; OS doesn't have ASPM control
[   11.748924] iwlwifi 0000:01:00.0: irq 48 for MSI/MSI-X
[   11.888094] [drm] Memory usable by graphics device = 2048M
[   11.888105] i915 0000:00:02.0: setting latency timer to 64
[   11.930500] i915 0000:00:02.0: irq 49 for MSI/MSI-X
[   11.930520] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[   11.930523] [drm] Driver supports precise vblank timestamp query.
[   11.930793] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[   11.941555] [drm] Wrong MCH_SSKPD value: 0x16040307
[   11.941559] [drm] This can cause pipe underruns and display issues.
[   11.941560] [drm] Please upgrade your BIOS to fix this.
[   11.941618] ------------[ cut here ]------------
[   11.941624] WARNING: CPU: 0 PID: 675 at kernel/workqueue.c:1445 __queue_delayed_work+0x18c/0x1a0()
[   11.941626] Modules linked in: i915(+) snd_page_alloc iwlwifi snd_seq_midi snd_seq_midi_event btusb psmouse snd_rawmidi snd_seq bluetooth cfg80211 i2c_algo_bit snd_timer samsung_laptop serio_raw snd_seq_device drm_kms_helper lpc_ich drm snd wmi mac_hid soundcore video lp parport hid_generic usbhid hid usb_storage r8169 mii
[   11.941651] CPU: 0 PID: 675 Comm: modprobe Not tainted 3.10.0-rc7-next20130628-1-iniza-small #1
[   11.941653] Hardware name: SAMSUNG ELECTRONICS CO., LTD. 530U3BI/530U4BI/530U4BH/530U3BI/530U4BI/530U4BH, BIOS 13XK 03/28/2013
[   11.941655]  00000000000005a5 ffff88010b5596a8 ffffffff816db223 0000000000001908
[   11.941658]  0000000000000000 ffff88010b5596e8 ffffffff810661cc ffffffffa00d3341
[   11.941661]  0000000000000100 ffff880119e72000 ffff88010765a000 0000000000000003
[   11.941664] Call Trace:
[   11.941671]  [<ffffffff816db223>] dump_stack+0x46/0x58
[   11.941675]  [<ffffffff810661cc>] warn_slowpath_common+0x8c/0xc0
[   11.941679]  [<ffffffff8106621a>] warn_slowpath_null+0x1a/0x20
[   11.941682]  [<ffffffff810845ac>] __queue_delayed_work+0x18c/0x1a0
[   11.941685]  [<ffffffff8108460d>] queue_delayed_work_on+0x4d/0x60
[   11.941691]  [<ffffffffa00f2950>] drm_helper_probe_single_connector_modes+0x270/0x420 [drm_kms_helper]
[   11.941696]  [<ffffffffa00f0f12>] drm_fb_helper_initial_config+0x1c2/0x550 [drm_kms_helper]
[   11.941700]  [<ffffffffa00f1721>] ? drm_fb_helper_single_add_all_connectors+0x81/0xe0 [drm_kms_helper]
[   11.941705]  [<ffffffff81193f7c>] ? kmem_cache_alloc_trace+0x1bc/0x1f0
[   11.941725]  [<ffffffffa024c481>] ? i915_write32+0x81/0x130 [i915]
[   11.941748]  [<ffffffffa02a2ee1>] intel_fbdev_initial_config+0x21/0x30 [i915]
[   11.941763]  [<ffffffffa0250512>] i915_driver_load+0xe32/0xe60 [i915]
[   11.941777]  [<ffffffffa00b1c01>] drm_get_pci_dev+0x181/0x2a0 [drm]
[   11.941781]  [<ffffffff81376add>] ? do_raw_spin_unlock+0x5d/0xb0
[   11.941794]  [<ffffffffa024b6e6>] i915_pci_probe+0x36/0x70 [i915]
[   11.941799]  [<ffffffff813954cb>] local_pci_probe+0x4b/0x80
[   11.941801]  [<ffffffff81396da1>] pci_device_probe+0x101/0x120
[   11.941806]  [<ffffffff814736bb>] driver_probe_device+0x7b/0x240
[   11.941809]  [<ffffffff8147392b>] __driver_attach+0xab/0xb0
[   11.941813]  [<ffffffff81473880>] ? driver_probe_device+0x240/0x240
[   11.941816]  [<ffffffff814719be>] bus_for_each_dev+0x5e/0x90
[   11.941819]  [<ffffffff814731de>] driver_attach+0x1e/0x20
[   11.941823]  [<ffffffff81472cd4>] bus_add_driver+0x104/0x270
[   11.941826]  [<ffffffff81473e8d>] driver_register+0x7d/0x160
[   11.941830]  [<ffffffff81395d24>] __pci_register_driver+0x64/0x70
[   11.941833]  [<ffffffffa02ee000>] ? 0xffffffffa02edfff
[   11.941842]  [<ffffffffa00b1e3a>] drm_pci_init+0x11a/0x130 [drm]
[   11.941844]  [<ffffffffa02ee000>] ? 0xffffffffa02edfff
[   11.941858]  [<ffffffffa02ee066>] i915_init+0x66/0x68 [i915]
[   11.941861]  [<ffffffff8100207e>] do_one_initcall+0x4e/0x180
[   11.941865]  [<ffffffff810584a3>] ? set_memory_nx+0x43/0x50
[   11.941869]  [<ffffffff810d09e9>] load_module+0x1cf9/0x2620
[   11.941872]  [<ffffffff810cd880>] ? show_initstate+0x50/0x50
[   11.941875]  [<ffffffff810d13bc>] SyS_init_module+0xac/0xd0
[   11.941879]  [<ffffffff816ec12f>] tracesys+0xe1/0xe6
[   11.941881] ---[ end trace a06c6f52b0f09abe ]---
[   11.941882] ------------[ cut here ]------------
[   11.941885] WARNING: CPU: 0 PID: 675 at kernel/workqueue.c:1447 __queue_delayed_work+0x12f/0x1a0()
[   11.941886] Modules linked in: i915(+) snd_page_alloc iwlwifi snd_seq_midi snd_seq_midi_event btusb psmouse snd_rawmidi snd_seq bluetooth cfg80211 i2c_algo_bit snd_timer samsung_laptop serio_raw snd_seq_device drm_kms_helper lpc_ich drm snd wmi mac_hid soundcore video lp parport hid_generic usbhid hid usb_storage r8169 mii
[   11.941905] CPU: 0 PID: 675 Comm: modprobe Tainted: G        W    3.10.0-rc7-next20130628-1-iniza-small #1
[   11.941906] Hardware name: SAMSUNG ELECTRONICS CO., LTD. 530U3BI/530U4BI/530U4BH/530U3BI/530U4BI/530U4BH, BIOS 13XK 03/28/2013
[   11.941908]  00000000000005a7 ffff88010b5596a8 ffffffff816db223 0000000000001b25
[   11.941911]  0000000000000000 ffff88010b5596e8 ffffffff810661cc ffffffffa00d3341
[   11.941913]  0000000000000100 ffff880119e72000 ffff88010765a000 0000000000000003
[   11.941916] Call Trace:
[   11.941919]  [<ffffffff816db223>] dump_stack+0x46/0x58
[   11.941922]  [<ffffffff810661cc>] warn_slowpath_common+0x8c/0xc0
[   11.941926]  [<ffffffff8106621a>] warn_slowpath_null+0x1a/0x20
[   11.941929]  [<ffffffff8108454f>] __queue_delayed_work+0x12f/0x1a0
[   11.941932]  [<ffffffff8108460d>] queue_delayed_work_on+0x4d/0x60
[   11.941936]  [<ffffffffa00f2950>] drm_helper_probe_single_connector_modes+0x270/0x420 [drm_kms_helper]
[   11.941940]  [<ffffffffa00f0f12>] drm_fb_helper_initial_config+0x1c2/0x550 [drm_kms_helper]
[   11.941945]  [<ffffffffa00f1721>] ? drm_fb_helper_single_add_all_connectors+0x81/0xe0 [drm_kms_helper]
[   11.941948]  [<ffffffff81193f7c>] ? kmem_cache_alloc_trace+0x1bc/0x1f0
[   11.941961]  [<ffffffffa024c481>] ? i915_write32+0x81/0x130 [i915]
[   11.941982]  [<ffffffffa02a2ee1>] intel_fbdev_initial_config+0x21/0x30 [i915]
[   11.941996]  [<ffffffffa0250512>] i915_driver_load+0xe32/0xe60 [i915]
[   11.942006]  [<ffffffffa00b1c01>] drm_get_pci_dev+0x181/0x2a0 [drm]
[   11.942009]  [<ffffffff81376add>] ? do_raw_spin_unlock+0x5d/0xb0
[   11.942021]  [<ffffffffa024b6e6>] i915_pci_probe+0x36/0x70 [i915]
[   11.942025]  [<ffffffff813954cb>] local_pci_probe+0x4b/0x80
[   11.942027]  [<ffffffff81396da1>] pci_device_probe+0x101/0x120
[   11.942031]  [<ffffffff814736bb>] driver_probe_device+0x7b/0x240
[   11.942034]  [<ffffffff8147392b>] __driver_attach+0xab/0xb0
[   11.942038]  [<ffffffff81473880>] ? driver_probe_device+0x240/0x240
[   11.942041]  [<ffffffff814719be>] bus_for_each_dev+0x5e/0x90
[   11.942044]  [<ffffffff814731de>] driver_attach+0x1e/0x20
[   11.942047]  [<ffffffff81472cd4>] bus_add_driver+0x104/0x270
[   11.942051]  [<ffffffff81473e8d>] driver_register+0x7d/0x160
[   11.942054]  [<ffffffff81395d24>] __pci_register_driver+0x64/0x70
[   11.942057]  [<ffffffffa02ee000>] ? 0xffffffffa02edfff
[   11.942064]  [<ffffffffa00b1e3a>] drm_pci_init+0x11a/0x130 [drm]
[   11.942067]  [<ffffffffa02ee000>] ? 0xffffffffa02edfff
[   11.942081]  [<ffffffffa02ee066>] i915_init+0x66/0x68 [i915]
[   11.942083]  [<ffffffff8100207e>] do_one_initcall+0x4e/0x180
[   11.942086]  [<ffffffff810584a3>] ? set_memory_nx+0x43/0x50
[   11.942089]  [<ffffffff810d09e9>] load_module+0x1cf9/0x2620
[   11.942092]  [<ffffffff810cd880>] ? show_initstate+0x50/0x50
[   11.942095]  [<ffffffff810d13bc>] SyS_init_module+0xac/0xd0
[   11.942098]  [<ffffffff816ec12f>] tracesys+0xe1/0xe6
[   11.942100] ---[ end trace a06c6f52b0f09abf ]---
[   11.942102] ------------[ cut here ]------------
[   11.942105] WARNING: CPU: 0 PID: 675 at kernel/workqueue.c:1378 __queue_work+0x2c3/0x3d0()
[   11.942106] Modules linked in: i915(+) snd_page_alloc iwlwifi snd_seq_midi snd_seq_midi_event btusb psmouse snd_rawmidi snd_seq bluetooth cfg80211 i2c_algo_bit snd_timer samsung_laptop serio_raw snd_seq_device drm_kms_helper lpc_ich drm snd wmi mac_hid soundcore video lp parport hid_generic usbhid hid usb_storage r8169 mii
[   11.942123] CPU: 0 PID: 675 Comm: modprobe Tainted: G        W    3.10.0-rc7-next20130628-1-iniza-small #1
[   11.942125] Hardware name: SAMSUNG ELECTRONICS CO., LTD. 530U3BI/530U4BI/530U4BH/530U3BI/530U4BI/530U4BH, BIOS 13XK 03/28/2013
[   11.942126]  0000000000000562 ffff88010b559658 ffffffff816db223 0000000000001d42
[   11.942129]  0000000000000000 ffff88010b559698 ffffffff810661cc ffff88010b559688
[   11.942132]  ffff88011fa17e00 ffff88010765a640 ffff880119e72000 0000000000000000
[   11.942134] Call Trace:
[   11.942137]  [<ffffffff816db223>] dump_stack+0x46/0x58
[   11.942140]  [<ffffffff810661cc>] warn_slowpath_common+0x8c/0xc0
[   11.942144]  [<ffffffff8106621a>] warn_slowpath_null+0x1a/0x20
[   11.942146]  [<ffffffff810842a3>] __queue_work+0x2c3/0x3d0
[   11.942149]  [<ffffffff810844d2>] __queue_delayed_work+0xb2/0x1a0
[   11.942152]  [<ffffffff8108460d>] queue_delayed_work_on+0x4d/0x60
[   11.942156]  [<ffffffffa00f2950>] drm_helper_probe_single_connector_modes+0x270/0x420 [drm_kms_helper]
[   11.942160]  [<ffffffffa00f0f12>] drm_fb_helper_initial_config+0x1c2/0x550 [drm_kms_helper]
[   11.942164]  [<ffffffffa00f1721>] ? drm_fb_helper_single_add_all_connectors+0x81/0xe0 [drm_kms_helper]
[   11.942168]  [<ffffffff81193f7c>] ? kmem_cache_alloc_trace+0x1bc/0x1f0
[   11.942180]  [<ffffffffa024c481>] ? i915_write32+0x81/0x130 [i915]
[   11.942199]  [<ffffffffa02a2ee1>] intel_fbdev_initial_config+0x21/0x30 [i915]
[   11.942212]  [<ffffffffa0250512>] i915_driver_load+0xe32/0xe60 [i915]
[   11.942221]  [<ffffffffa00b1c01>] drm_get_pci_dev+0x181/0x2a0 [drm]
[   11.942224]  [<ffffffff81376add>] ? do_raw_spin_unlock+0x5d/0xb0
[   11.942236]  [<ffffffffa024b6e6>] i915_pci_probe+0x36/0x70 [i915]
[   11.942239]  [<ffffffff813954cb>] local_pci_probe+0x4b/0x80
[   11.942242]  [<ffffffff81396da1>] pci_device_probe+0x101/0x120
[   11.942245]  [<ffffffff814736bb>] driver_probe_device+0x7b/0x240
[   11.942249]  [<ffffffff8147392b>] __driver_attach+0xab/0xb0
[   11.942252]  [<ffffffff81473880>] ? driver_probe_device+0x240/0x240
[   11.942255]  [<ffffffff814719be>] bus_for_each_dev+0x5e/0x90
[   11.942258]  [<ffffffff814731de>] driver_attach+0x1e/0x20
[   11.942262]  [<ffffffff81472cd4>] bus_add_driver+0x104/0x270
[   11.942265]  [<ffffffff81473e8d>] driver_register+0x7d/0x160
[   11.942268]  [<ffffffff81395d24>] __pci_register_driver+0x64/0x70
[   11.942271]  [<ffffffffa02ee000>] ? 0xffffffffa02edfff
[   11.942279]  [<ffffffffa00b1e3a>] drm_pci_init+0x11a/0x130 [drm]
[   11.942281]  [<ffffffffa02ee000>] ? 0xffffffffa02edfff
[   11.942295]  [<ffffffffa02ee066>] i915_init+0x66/0x68 [i915]
[   11.942297]  [<ffffffff8100207e>] do_one_initcall+0x4e/0x180
[   11.942300]  [<ffffffff810584a3>] ? set_memory_nx+0x43/0x50
[   11.942303]  [<ffffffff810d09e9>] load_module+0x1cf9/0x2620
[   11.942306]  [<ffffffff810cd880>] ? show_initstate+0x50/0x50
[   11.942309]  [<ffffffff810d13bc>] SyS_init_module+0xac/0xd0
[   11.942312]  [<ffffffff816ec12f>] tracesys+0xe1/0xe6
[   11.942314] ---[ end trace a06c6f52b0f09ac0 ]---
[   11.960881] fbcon: inteldrmfb (fb0) is primary device
[   12.193901] Linux video capture interface: v2.00
[   12.413220] iwlwifi 0000:01:00.0: loaded firmware version 18.168.6.1 op_mode iwldvm
[   12.425156] psmouse serio1: elantech: assuming hardware version 3 (with firmware version 0x450f00)
[   12.448093] psmouse serio1: elantech: Synaptics capabilities query result 0x08, 0x17, 0x0c.
[   12.525834] input: ETPS/2 Elantech Touchpad as /devices/platform/i8042/serio1/input/input5
[   12.708953] cfg80211: World regulatory domain updated:
[   12.708954] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   12.708956] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   12.708957] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   12.708958] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   12.708959] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   12.708960] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   12.884946] ppdev: user-space parallel port driver
[   12.904115] uvcvideo 1-1.4:1.0: usb_probe_interface
[   12.904119] uvcvideo 1-1.4:1.0: usb_probe_interface - got id
[   12.904168] uvcvideo: Found UVC 1.00 device WebCam SC-13HDL11431N (2232:1018)
[   12.923420] input: WebCam SC-13HDL11431N as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.4/1-1.4:1.0/input/input6
[   12.923604] usbcore: registered new interface driver uvcvideo
[   12.923605] USB Video Class driver (1.1.1)
[   12.961485] usb 1-1.4: link qh16-0001/ffff88010fc61340 start 2 [1/0 us]
[   12.961550] usb 1-1.4: unlink qh16-0001/ffff88010fc61340 start 2 [1/0 us]
[   12.987939] Console: switching to colour frame buffer device 170x48
[   12.990908] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
[   12.990910] i915 0000:00:02.0: registered panic notifier
[   13.010605] acpi device:33: registered as cooling_device9
[   13.010995] ACPI: Video Device [GFX0] (multi-head: yes  rom: no  post: no)
[   13.011089] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input7
[   13.011292] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[   13.011684] snd_hda_intel 0000:00:1b.0: irq 50 for MSI/MSI-X
[   13.183876] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8
[   13.184135] input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9
[   13.184424] input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10
[   13.192972] iwlwifi 0000:01:00.0: CONFIG_IWLWIFI_DEBUG enabled
[   13.192978] iwlwifi 0000:01:00.0: CONFIG_IWLWIFI_DEBUGFS enabled
[   13.192981] iwlwifi 0000:01:00.0: CONFIG_IWLWIFI_DEVICE_TRACING enabled
[   13.192983] iwlwifi 0000:01:00.0: CONFIG_IWLWIFI_P2P disabled
[   13.192986] iwlwifi 0000:01:00.0: Detected Intel(R) Centrino(R) Advanced-N 6230 AGN, REV=0xB0
[   13.193038] iwlwifi 0000:01:00.0: L1 Enabled; Disabling L0S
[   13.344643] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs'
[   13.690825] Bluetooth: RFCOMM TTY layer initialized
[   13.690852] Bluetooth: RFCOMM socket layer initialized
[   13.690855] Bluetooth: RFCOMM ver 1.11
[   13.712178] usb 2-1.5: unlink qh1-0e01/ffff880116c585c0 start 0 [1/2 us]
[   13.714758] usb 2-1: clear tt buffer port 5, a3 ep2 t04048d80
[   13.820289] [drm] Enabling RC6 states: RC6 on, RC6p off, RC6pp off
[   13.840844] type=1400 audit(1372406506.759:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=911 comm="apparmor_parser"
[   13.841600] type=1400 audit(1372406506.759:3): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=911 comm="apparmor_parser"
[   13.842080] type=1400 audit(1372406506.759:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=911 comm="apparmor_parser"
[   13.842813] type=1400 audit(1372406506.759:5): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=984 comm="apparmor_parser"
[   13.843568] type=1400 audit(1372406506.759:6): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=984 comm="apparmor_parser"
[   13.843959] type=1400 audit(1372406506.759:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=984 comm="apparmor_parser"
[   13.844385] type=1400 audit(1372406506.763:8): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=865 comm="apparmor_parser"
[   13.845148] type=1400 audit(1372406506.763:9): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=865 comm="apparmor_parser"
[   13.845627] type=1400 audit(1372406506.763:10): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=865 comm="apparmor_parser"
[   13.886185] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   13.886190] Bluetooth: BNEP filters: protocol multicast
[   13.886209] Bluetooth: BNEP socket layer initialized
[   13.992600] ehci-pci 0000:00:1d.0: reused qh ffff880116c585c0 schedule
[   13.992609] usb 2-1.5: link qh1-0e01/ffff880116c585c0 start 0 [1/2 us]
[   14.035545] type=1400 audit(1372406506.951:11): apparmor="STATUS" operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" pid=943 comm="apparmor_parser"
[   14.959380] usb 1-1.4: usb auto-suspend, wakeup 0
[   15.396158] init: failsafe main process (1012) killed by TERM signal
[   19.068416] iwlwifi 0000:01:00.0: L1 Enabled; Disabling L0S
[   19.075054] iwlwifi 0000:01:00.0: Radio type=0x1-0x2-0x0
[   19.349528] iwlwifi 0000:01:00.0: L1 Enabled; Disabling L0S
[   19.356224] iwlwifi 0000:01:00.0: Radio type=0x1-0x2-0x0
[   19.433654] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   20.666940] usb 1-1.2: link qh8-0e01/ffff88010fc61a40 start 3 [1/2 us]
[   25.944835] wlan0: authenticate with 00:04:0e:e4:00:3d
[   25.947718] wlan0: send auth to 00:04:0e:e4:00:3d (try 1/3)
[   25.949435] wlan0: authenticated
[   25.949619] iwlwifi 0000:01:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP
[   25.949624] iwlwifi 0000:01:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP
[   25.951472] wlan0: associate with 00:04:0e:e4:00:3d (try 1/3)
[   25.954944] wlan0: RX AssocResp from 00:04:0e:e4:00:3d (capab=0x411 status=0 aid=1)
[   25.958784] wlan0: associated
[   25.958877] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   29.498978] usb usb3: usb auto-resume
[   29.499001] hub 3-0:1.0: hub_resume
[   29.499033] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   29.499051] hub 3-0:1.0: hub_suspend
[   29.499059] usb usb3: bus auto-suspend, wakeup 1
[   29.499082] usb usb3: usb auto-resume
[   29.508983] hub 3-0:1.0: hub_resume
[   29.509012] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   29.509027] hub 3-0:1.0: hub_suspend
[   29.509033] usb usb3: bus auto-suspend, wakeup 1
[   29.509724] usb 1-1.4: usb auto-resume
[   29.557102] usb 1-1.4: finish resume
[   29.726987] usb usb3: usb auto-resume
[   29.727009] hub 3-0:1.0: hub_resume
[   29.727039] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   29.727049] hub 3-0:1.0: hub_suspend
[   29.727056] usb usb3: bus auto-suspend, wakeup 1
[   29.727154] usb usb3: usb auto-resume
[   29.736816] hub 3-0:1.0: hub_resume
[   29.736842] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   29.736858] hub 3-0:1.0: hub_suspend
[   29.736864] usb usb3: bus auto-suspend, wakeup 1
[   29.749754] usb usb3: usb auto-resume
[   29.749773] hub 3-0:1.0: hub_resume
[   29.749823] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   29.750232] hub 3-0:1.0: hub_suspend
[   29.750239] usb usb3: bus auto-suspend, wakeup 1
[   29.750291] usb usb3: usb auto-resume
[   29.760782] hub 3-0:1.0: hub_resume
[   29.760803] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   29.760822] hub 3-0:1.0: hub_suspend
[   29.760827] usb usb3: bus auto-suspend, wakeup 1
[   29.803634] usb usb3: usb auto-resume
[   29.803657] hub 3-0:1.0: hub_resume
[   29.803685] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   29.803701] hub 3-0:1.0: hub_suspend
[   29.803708] usb usb3: bus auto-suspend, wakeup 1
[   29.803776] usb usb3: usb auto-resume
[   29.812750] hub 3-0:1.0: hub_resume
[   29.812773] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   29.812792] hub 3-0:1.0: hub_suspend
[   29.812797] usb usb3: bus auto-suspend, wakeup 1
[   29.938732] usb usb3: usb auto-resume
[   29.938754] hub 3-0:1.0: hub_resume
[   29.938785] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   29.938811] hub 3-0:1.0: hub_suspend
[   29.938820] usb usb3: bus auto-suspend, wakeup 1
[   29.938841] usb usb3: usb auto-resume
[   29.948681] hub 3-0:1.0: hub_resume
[   29.948716] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   29.948736] hub 3-0:1.0: hub_suspend
[   29.948744] usb usb3: bus auto-suspend, wakeup 1
[   29.960386] usb usb3: usb auto-resume
[   29.968755] hub 3-0:1.0: hub_resume
[   29.968783] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   29.968814] hub 3-0:1.0: hub_suspend
[   29.968820] usb usb3: bus auto-suspend, wakeup 1
[   29.968876] usb usb3: usb auto-resume
[   29.980670] hub 3-0:1.0: hub_resume
[   29.980696] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   29.980712] hub 3-0:1.0: hub_suspend
[   29.980717] usb usb3: bus auto-suspend, wakeup 1
[   30.003412] usb usb3: usb auto-resume
[   30.003433] hub 3-0:1.0: hub_resume
[   30.003513] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   30.003586] hub 3-0:1.0: hub_suspend
[   30.003593] usb usb3: bus auto-suspend, wakeup 1
[   30.003772] usb usb3: usb auto-resume
[   30.012602] hub 3-0:1.0: hub_resume
[   30.012625] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   30.012647] hub 3-0:1.0: hub_suspend
[   30.012652] usb usb3: bus auto-suspend, wakeup 1
[   30.159125] usb usb3: usb auto-resume
[   30.159149] hub 3-0:1.0: hub_resume
[   30.159178] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   30.159200] hub 3-0:1.0: hub_suspend
[   30.159207] usb usb3: bus auto-suspend, wakeup 1
[   30.159273] usb usb3: usb auto-resume
[   30.168505] hub 3-0:1.0: hub_resume
[   30.168533] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   30.168543] hub 3-0:1.0: hub_suspend
[   30.168550] usb usb3: bus auto-suspend, wakeup 1
[   30.179696] usb usb3: usb auto-resume
[   30.188482] hub 3-0:1.0: hub_resume
[   30.188507] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   30.188531] hub 3-0:1.0: hub_suspend
[   30.188536] usb usb3: bus auto-suspend, wakeup 1
[   30.188584] usb usb3: usb auto-resume
[   30.200476] hub 3-0:1.0: hub_resume
[   30.200499] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   30.200517] hub 3-0:1.0: hub_suspend
[   30.200523] usb usb3: bus auto-suspend, wakeup 1
[   30.731227] usb usb3: usb auto-resume
[   30.731250] hub 3-0:1.0: hub_resume
[   30.731286] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   30.731302] hub 3-0:1.0: hub_suspend
[   30.731308] usb usb3: bus auto-suspend, wakeup 1
[   30.731332] usb usb3: usb auto-resume
[   30.740113] hub 3-0:1.0: hub_resume
[   30.740138] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   30.740150] hub 3-0:1.0: hub_suspend
[   30.740155] usb usb3: bus auto-suspend, wakeup 1
[   30.926216] usb usb3: usb auto-resume
[   30.926239] hub 3-0:1.0: hub_resume
[   30.926270] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   30.926280] hub 3-0:1.0: hub_suspend
[   30.926287] usb usb3: bus auto-suspend, wakeup 1
[   30.926349] usb usb3: usb auto-resume
[   30.935992] hub 3-0:1.0: hub_resume
[   30.937733] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   30.937769] hub 3-0:1.0: hub_suspend
[   30.937781] usb usb3: bus auto-suspend, wakeup 1
[   32.021288] usb usb3: usb auto-resume
[   32.021309] hub 3-0:1.0: hub_resume
[   32.021339] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   32.021366] hub 3-0:1.0: hub_suspend
[   32.021372] usb usb3: bus auto-suspend, wakeup 1
[   32.021400] usb usb3: usb auto-resume
[   32.031190] hub 3-0:1.0: hub_resume
[   32.032198] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   32.032214] hub 3-0:1.0: hub_suspend
[   32.032222] usb usb3: bus auto-suspend, wakeup 1
[   32.056005] usb usb3: usb auto-resume
[   32.056028] hub 3-0:1.0: hub_resume
[   32.056397] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   32.056415] hub 3-0:1.0: hub_suspend
[   32.056423] usb usb3: bus auto-suspend, wakeup 1
[   32.081747] usb usb3: usb auto-resume
[   32.081769] hub 3-0:1.0: hub_resume
[   32.081797] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   32.082148] hub 3-0:1.0: hub_suspend
[   32.082157] usb usb3: bus auto-suspend, wakeup 1
[   32.082227] usb usb3: usb auto-resume
[   32.091137] hub 3-0:1.0: hub_resume
[   32.091167] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   32.091184] hub 3-0:1.0: hub_suspend
[   32.091191] usb usb3: bus auto-suspend, wakeup 1
[   32.172044] usb usb3: usb auto-resume
[   32.172066] hub 3-0:1.0: hub_resume
[   32.172096] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   32.172121] hub 3-0:1.0: hub_suspend
[   32.172129] usb usb3: bus auto-suspend, wakeup 1
[   32.172152] usb usb3: usb auto-resume
[   32.183099] hub 3-0:1.0: hub_resume
[   32.183126] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   32.183142] hub 3-0:1.0: hub_suspend
[   32.183148] usb usb3: bus auto-suspend, wakeup 1
[   32.184433] usb usb3: usb auto-resume
[   32.195072] hub 3-0:1.0: hub_resume
[   32.195099] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   32.195123] hub 3-0:1.0: hub_suspend
[   32.195129] usb usb3: bus auto-suspend, wakeup 1
[   32.195202] usb usb3: usb auto-resume
[   32.207061] hub 3-0:1.0: hub_resume
[   32.207088] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   32.207138] hub 3-0:1.0: hub_suspend
[   32.207144] usb usb3: bus auto-suspend, wakeup 1
[   32.209737] usb usb3: usb auto-resume
[   32.219057] hub 3-0:1.0: hub_resume
[   32.219091] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   32.219118] hub 3-0:1.0: hub_suspend
[   32.219125] usb usb3: bus auto-suspend, wakeup 1
[   32.219199] usb usb3: usb auto-resume
[   32.231043] hub 3-0:1.0: hub_resume
[   32.231073] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   32.231090] hub 3-0:1.0: hub_suspend
[   32.231096] usb usb3: bus auto-suspend, wakeup 1
[   32.233869] usb usb3: usb auto-resume
[   32.243032] hub 3-0:1.0: hub_resume
[   32.243064] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   32.243091] hub 3-0:1.0: hub_suspend
[   32.243096] usb usb3: bus auto-suspend, wakeup 1
[   32.243151] usb usb3: usb auto-resume
[   32.255032] hub 3-0:1.0: hub_resume
[   32.255061] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   32.255077] hub 3-0:1.0: hub_suspend
[   32.255082] usb usb3: bus auto-suspend, wakeup 1
[   32.270413] usb usb3: usb auto-resume
[   32.270434] hub 3-0:1.0: hub_resume
[   32.270459] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   32.270473] hub 3-0:1.0: hub_suspend
[   32.270480] usb usb3: bus auto-suspend, wakeup 1
[   32.270526] usb usb3: usb auto-resume
[   32.279013] hub 3-0:1.0: hub_resume
[   32.279050] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   32.279070] hub 3-0:1.0: hub_suspend
[   32.279078] usb usb3: bus auto-suspend, wakeup 1
[   32.302480] usb usb3: usb auto-resume
[   32.302504] hub 3-0:1.0: hub_resume
[   32.302566] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   32.302630] hub 3-0:1.0: hub_suspend
[   32.302638] usb usb3: bus auto-suspend, wakeup 1
[   32.302709] usb usb3: usb auto-resume
[   32.311222] hub 3-0:1.0: hub_resume
[   32.311259] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   32.311358] hub 3-0:1.0: hub_suspend
[   32.311367] usb usb3: bus auto-suspend, wakeup 1
[   32.312729] usb usb3: usb auto-resume
[   32.322973] hub 3-0:1.0: hub_resume
[   32.323003] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   32.323029] hub 3-0:1.0: hub_suspend
[   32.323033] usb usb3: bus auto-suspend, wakeup 1
[   32.323086] usb usb3: usb auto-resume
[   32.334962] hub 3-0:1.0: hub_resume
[   32.334983] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   32.335003] hub 3-0:1.0: hub_suspend
[   32.335008] usb usb3: bus auto-suspend, wakeup 1
[   32.391701] usb usb3: usb auto-resume
[   32.391722] hub 3-0:1.0: hub_resume
[   32.391749] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   32.391765] hub 3-0:1.0: hub_suspend
[   32.391771] usb usb3: bus auto-suspend, wakeup 1
[   32.391816] usb usb3: usb auto-resume
[   32.402968] hub 3-0:1.0: hub_resume
[   32.403002] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   32.403023] hub 3-0:1.0: hub_suspend
[   32.403031] usb usb3: bus auto-suspend, wakeup 1
[   32.411046] usb usb3: usb auto-resume
[   32.422937] hub 3-0:1.0: hub_resume
[   32.422969] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   32.422980] hub 3-0:1.0: hub_suspend
[   32.422987] usb usb3: bus auto-suspend, wakeup 1
[   32.423066] usb usb3: usb auto-resume
[   32.434902] hub 3-0:1.0: hub_resume
[   32.434931] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   32.434949] hub 3-0:1.0: hub_suspend
[   32.434956] usb usb3: bus auto-suspend, wakeup 1
[   32.457048] usb usb3: usb auto-resume
[   32.457069] hub 3-0:1.0: hub_resume
[   32.457096] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   32.457148] hub 3-0:1.0: hub_suspend
[   32.457155] usb usb3: bus auto-suspend, wakeup 1
[   32.457221] usb usb3: usb auto-resume
[   32.466886] hub 3-0:1.0: hub_resume
[   32.466910] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   32.466923] hub 3-0:1.0: hub_suspend
[   32.466927] usb usb3: bus auto-suspend, wakeup 1
[   32.487565] usb usb3: usb auto-resume
[   32.487587] hub 3-0:1.0: hub_resume
[   32.487618] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   32.487635] hub 3-0:1.0: hub_suspend
[   32.487643] usb usb3: bus auto-suspend, wakeup 1
[   32.487667] usb usb3: usb auto-resume
[   32.498904] hub 3-0:1.0: hub_resume
[   32.498942] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   32.498956] hub 3-0:1.0: hub_suspend
[   32.498964] usb usb3: bus auto-suspend, wakeup 1
[   32.513220] usb usb3: usb auto-resume
[   32.513242] hub 3-0:1.0: hub_resume
[   32.513270] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   32.513293] hub 3-0:1.0: hub_suspend
[   32.513300] usb usb3: bus auto-suspend, wakeup 1
[   32.513364] usb usb3: usb auto-resume
[   32.522840] hub 3-0:1.0: hub_resume
[   32.522875] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   32.522894] hub 3-0:1.0: hub_suspend
[   32.522901] usb usb3: bus auto-suspend, wakeup 1
[   32.613919] usb usb3: usb auto-resume
[   32.613943] hub 3-0:1.0: hub_resume
[   32.614435] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   32.618913] hub 3-0:1.0: hub_suspend
[   32.618930] usb usb3: bus auto-suspend, wakeup 1
[   32.625846] usb usb3: usb auto-resume
[   32.634767] hub 3-0:1.0: hub_resume
[   32.634804] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   32.634838] hub 3-0:1.0: hub_suspend
[   32.634847] usb usb3: bus auto-suspend, wakeup 1
[   32.634929] usb usb3: usb auto-resume
[   32.646784] hub 3-0:1.0: hub_resume
[   32.646822] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   32.646843] hub 3-0:1.0: hub_suspend
[   32.646852] usb usb3: bus auto-suspend, wakeup 1
[   32.681480] usb usb3: usb auto-resume
[   32.681502] hub 3-0:1.0: hub_resume
[   32.682151] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   32.682168] hub 3-0:1.0: hub_suspend
[   32.682176] usb usb3: bus auto-suspend, wakeup 1
[   32.699227] usb usb3: usb auto-resume
[   32.699248] hub 3-0:1.0: hub_resume
[   32.699277] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   32.699300] hub 3-0:1.0: hub_suspend
[   32.699306] usb usb3: bus auto-suspend, wakeup 1
[   32.699333] usb usb3: usb auto-resume
[   32.710713] hub 3-0:1.0: hub_resume
[   32.710745] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   32.710758] hub 3-0:1.0: hub_suspend
[   32.710765] usb usb3: bus auto-suspend, wakeup 1
[   32.713566] usb usb3: usb auto-resume
[   32.722700] hub 3-0:1.0: hub_resume
[   32.722752] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   32.722785] hub 3-0:1.0: hub_suspend
[   32.722791] usb usb3: bus auto-suspend, wakeup 1
[   32.722861] usb usb3: usb auto-resume
[   32.734692] hub 3-0:1.0: hub_resume
[   32.734726] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   32.734741] hub 3-0:1.0: hub_suspend
[   32.734749] usb usb3: bus auto-suspend, wakeup 1
[   32.751535] usb usb3: usb auto-resume
[   32.751559] hub 3-0:1.0: hub_resume
[   32.751590] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   32.751610] hub 3-0:1.0: hub_suspend
[   32.751618] usb usb3: bus auto-suspend, wakeup 1
[   32.751668] usb usb3: usb auto-resume
[   32.762670] hub 3-0:1.0: hub_resume
[   32.762699] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   32.762722] hub 3-0:1.0: hub_suspend
[   32.762728] usb usb3: bus auto-suspend, wakeup 1
[   33.802670] usb usb3: usb auto-resume
[   33.802691] hub 3-0:1.0: hub_resume
[   33.802716] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   33.802734] hub 3-0:1.0: hub_suspend
[   33.802741] usb usb3: bus auto-suspend, wakeup 1
[   33.802787] usb usb3: usb auto-resume
[   33.813924] hub 3-0:1.0: hub_resume
[   33.813950] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   33.813971] hub 3-0:1.0: hub_suspend
[   33.813977] usb usb3: bus auto-suspend, wakeup 1
[   34.118934] usb usb3: usb auto-resume
[   34.118955] hub 3-0:1.0: hub_resume
[   34.118981] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   34.119003] hub 3-0:1.0: hub_suspend
[   34.119008] usb usb3: bus auto-suspend, wakeup 1
[   34.119055] usb usb3: usb auto-resume
[   34.129698] hub 3-0:1.0: hub_resume
[   34.129725] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   34.129748] hub 3-0:1.0: hub_suspend
[   34.129754] usb usb3: bus auto-suspend, wakeup 1
[   34.156767] usb usb3: usb auto-resume
[   34.156786] hub 3-0:1.0: hub_resume
[   34.156814] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   34.156829] hub 3-0:1.0: hub_suspend
[   34.156834] usb usb3: bus auto-suspend, wakeup 1
[   34.156864] usb usb3: usb auto-resume
[   34.165677] hub 3-0:1.0: hub_resume
[   34.165702] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   34.165722] hub 3-0:1.0: hub_suspend
[   34.165727] usb usb3: bus auto-suspend, wakeup 1
[   34.168212] usb usb3: usb auto-resume
[   34.177667] hub 3-0:1.0: hub_resume
[   34.177694] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   34.177715] hub 3-0:1.0: hub_suspend
[   34.177721] usb usb3: bus auto-suspend, wakeup 1
[   34.177774] usb usb3: usb auto-resume
[   34.189652] hub 3-0:1.0: hub_resume
[   34.189676] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   34.189696] hub 3-0:1.0: hub_suspend
[   34.189702] usb usb3: bus auto-suspend, wakeup 1
[   34.192319] usb usb3: usb auto-resume
[   34.201666] hub 3-0:1.0: hub_resume
[   34.201698] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   34.201719] hub 3-0:1.0: hub_suspend
[   34.201724] usb usb3: bus auto-suspend, wakeup 1
[   34.201777] usb usb3: usb auto-resume
[   34.213642] hub 3-0:1.0: hub_resume
[   34.213668] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   34.213690] hub 3-0:1.0: hub_suspend
[   34.213696] usb usb3: bus auto-suspend, wakeup 1
[   34.251268] usb usb3: usb auto-resume
[   34.251288] hub 3-0:1.0: hub_resume
[   34.251315] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   34.251335] hub 3-0:1.0: hub_suspend
[   34.251340] usb usb3: bus auto-suspend, wakeup 1
[   34.251386] usb usb3: usb auto-resume
[   34.261594] hub 3-0:1.0: hub_resume
[   34.261614] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   34.261626] hub 3-0:1.0: hub_suspend
[   34.261631] usb usb3: bus auto-suspend, wakeup 1
[   34.265411] usb usb3: usb auto-resume
[   34.273598] hub 3-0:1.0: hub_resume
[   34.273626] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   34.273657] hub 3-0:1.0: hub_suspend
[   34.273662] usb usb3: bus auto-suspend, wakeup 1
[   34.273716] usb usb3: usb auto-resume
[   34.285590] hub 3-0:1.0: hub_resume
[   34.285618] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   34.285637] hub 3-0:1.0: hub_suspend
[   34.285642] usb usb3: bus auto-suspend, wakeup 1
[   34.396448] usb usb3: usb auto-resume
[   34.396471] hub 3-0:1.0: hub_resume
[   34.396502] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   34.396523] hub 3-0:1.0: hub_suspend
[   34.396529] usb usb3: bus auto-suspend, wakeup 1
[   34.396557] usb usb3: usb auto-resume
[   34.405526] hub 3-0:1.0: hub_resume
[   34.405554] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   34.405569] hub 3-0:1.0: hub_suspend
[   34.405574] usb usb3: bus auto-suspend, wakeup 1
[   36.791916] usb 1-1.4: usb auto-suspend, wakeup 0
[   43.638322] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)
[   43.669317] EXT4-fs (sdc3): mounted filesystem with ordered data mode. Opts: (null)
[   51.658938] usb 2-1.5: unlink qh1-0e01/ffff880116c585c0 start 0 [1/2 us]
[   51.686999] hub 2-1:1.0: state 7 ports 6 chg 0000 evt 0020
[   51.687235] hub 2-1:1.0: port 5, status 0100, change 0001, 12 Mb/s
[   51.687240] usb 2-1.5: USB disconnect, device number 3
[   51.687242] usb 2-1.5: unregistering device
[   51.687245] usb 2-1.5: unregistering interface 2-1.5:1.0
[   51.691619] usb 2-1.5: unregistering interface 2-1.5:1.1
[   51.691733] usb 2-1.5: usb_disable_device nuking all URBs
[   51.816533] hub 2-1:1.0: debounce: port 5: total 100ms stable 100ms status 0x100
[   51.816552] hub 2-1:1.0: hub_suspend
[   51.816561] usb 2-1: unlink qh256-0001/ffff880118696bc0 start 1 [1/0 us]
[   51.818781] usb 2-1: usb auto-suspend, wakeup 1
[   51.832431] hub 2-0:1.0: hub_suspend
[   51.832439] usb usb2: bus auto-suspend, wakeup 1
[   51.832442] ehci-pci 0000:00:1d.0: suspend root hub

Attachment: config-3.10.0-rc7-next20130628-1-iniza-small
Description: Binary data