Re: [PATCH v2 3/5] mmc: dw_mmc: Add exynos resume_noirq callback toclear WAKEUP_INT

[Doug Anderson]

Seungwon,

On Wed, Jul 10, 2013 at 7:54 AM, Seungwon Jeon <tgih.jun@xxxxxxxxxxx> wrote:
> On Wed, July 10, 2013, Doug Anderson wrote:
>> If the WAKEUP_INT is asserted at wakeup and not cleared, we'll end up
>> looping around forever.  This has been seen to happen on exynos5420
>> silicon despite the fact that we haven't enabled any wakeup events.
>>
>> Signed-off-by: Doug Anderson <dianders@xxxxxxxxxxxx>
>> ---
>> Changes in v2:
>> - Use suspend_noirq as per James Hogan.
>>
>>  drivers/mmc/host/dw_mmc-exynos.c | 23 +++++++++++++++++++++++
>>  1 file changed, 23 insertions(+)
>>
>> diff --git a/drivers/mmc/host/dw_mmc-exynos.c b/drivers/mmc/host/dw_mmc-exynos.c
>> index f013e7e..36b9620 100644
>> --- a/drivers/mmc/host/dw_mmc-exynos.c
>> +++ b/drivers/mmc/host/dw_mmc-exynos.c
>> @@ -30,6 +30,7 @@
>>  #define SDMMC_CLKSEL_TIMING(x, y, z) (SDMMC_CLKSEL_CCLK_SAMPLE(x) |  \
>>                                       SDMMC_CLKSEL_CCLK_DRIVE(y) |    \
>>                                       SDMMC_CLKSEL_CCLK_DIVIDER(z))
>> +#define SDMMC_CLKSEL_WAKEUP_INT              BIT(11)
>>
>>  #define SDMMC_CMD_USE_HOLD_REG               BIT(29)
>>
>> @@ -102,6 +103,27 @@ static int dw_mci_exynos_setup_clock(struct dw_mci *host)
>>       return 0;
>>  }
>>
>> +/**
>> + * dw_mci_exynos_resume_noirq - Exynos-specific resume code
>> + *
>> + * We have seen cases (at least on the exynos5420) where turning off the INT
>> + * power rail during suspend will leave the WAKEUP_INT bit in the CLKSEL
>> + * register asserted.  This bit is 1 to indicate that it fired and we can
>> + * clear it by writing a 1 back.  Clear it to prevent interrupts from going off
>> + * constantly.
>> + */
> As I know this bit is auto-cleared.
> Did you find the cause of this problem?
> How about your GPIO setting in sleep?
> Currently, we don't know why the problem is happened.
> At least, we should make it clear.

Yes, the documentation that I have says that this bit is "auto
cleared" as well but doesn't indicate under what conditions it is auto
cleared.  From testing how this bit reacts I have found that writing a
1 to it clears the bit--in other words it behaves like bits in
RINTSTS.  That's a terrible design for a bit in a register with shared
config but appears to be how it works.

Note: in a sense it will be "auto cleared" because doing a
read-modify-write of any other bits in this register will clear the
interrupt.

I have asked for official confirmation.

We have found that on exynos5420 bits 8-10 of CLKSEL are marked as
RESERVED.  Those bits are documented to enable the WAKEUP_INT on
exynos5250.  My best guess is that these bits are not used on
exynos5420 and the WAKEUP_INT line is left floating, which means it
can fire randomly.  I have also asked for official confirmation about
this.


I will likely merge this change locally in our kernel tree while
waiting for a response.  If you would like to wait before Acking
that's very reasonable.  Do you have any other problems with this
change assuming my understanding above is correct?

-Doug
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/