Re: [PATCH] ARM: DTS: DRA7: Add TPS659038 PMIC nodes

[Keerthy]

Hi Nishanth,


On Thursday 15 August 2013 05:05 AM, Nishanth Menon wrote:
> linux-omap, linux-arm-list should also be CCed, Benoit needs to be
> addressed for allowing him to merge,

My Bad. I will resend with looping in both the lists and the comments
addressed.

> I have not done a proper schematics Vs data manual review yet
> (apologies on that), but, a couple of comments:
>
> On 08/13/2013 12:42 AM, Keerthy wrote:
> > The Patch adds nodes for TPS659038 PMIC for DRA7 boards.
> >
> > It is based on:
> > http://comments.gmane.org/gmane.linux.ports.arm.omap/102459.
> >
> > Documentation:	Documentation/devicetree/bindings/mfd/palmas.txt
> > 		Documentation/devicetree/bindings/regulator/palmas-pmic.txt		
> >
> > Tested on DRA7 Board, 3.11-rc5 plus the above patch-set.
> >
> > Signed-off-by: Keerthy <j-keerthy@xxxxxx>
> > ---
> >   arch/arm/boot/dts/dra7-evm.dts |  118 ++++++++++++++++++++++++++++++++++++++++
> >   1 file changed, 118 insertions(+)
> >
> > diff --git a/arch/arm/boot/dts/dra7-evm.dts b/arch/arm/boot/dts/dra7-evm.dts
> > index b270e24..96f409f 100644
> > --- a/arch/arm/boot/dts/dra7-evm.dts
> > +++ b/arch/arm/boot/dts/dra7-evm.dts
> > @@ -93,6 +93,124 @@
> >   	pinctrl-names = "default";
> >   	pinctrl-0 = <&i2c1_pins>;
> >   	clock-frequency = <400000>;
> > +
> > +	tps659038: tps659038@58 {
> > +		compatible = "ti,tps659038";
> > +		reg = <0x58>;
> > +		interrupt-controller;
> > +		#interrupt-cells = <2>;
> Where is the interrupt line to MPU? if it is not hooked up, why the
> interrupt controller?

It is not hooked up. I will remove this.

> > +
> > +		tps659038_pmic {
> > +			compatible = "ti,tps659038-pmic";
> > +
> > +			regulators {
> > +				smps123_reg: smps123 {
> > +					/* VDD_MPU */
> 					^^ tab issue?
> > +						regulator-name = "smps123";
> > +						regulator-min-microvolt = < 600000>;
> > +						regulator-max-microvolt = <1500000>;
> > +						regulator-always-on;
> > +						regulator-boot-on;
> > +					};
> > +
> > +				smps45_reg: smps45 {
> > +						/* VDD_DSPEVE */
> > +						regulator-name = "smps45";
> > +						regulator-min-microvolt = < 600000>;
> > +						regulator-max-microvolt = <1310000>;
> > +						regulator-always-on;
> > +						regulator-boot-on;
> > +					};
> > +
> > +				smps6_reg: smps6 {
> > +						/* VDD_GPU - over VDD_SMPS6 */
> > +						regulator-name = "smps6";
> > +						regulator-min-microvolt = <600000>;
> > +						regulator-max-microvolt = <13100000>;
> > +						regulator-always-on;
> > +						regulator-boot-on;
> > +					};
> > +
> > +				smps7_reg: smps7 {
> > +						/* VDDS_CORE */
> > +						regulator-name = "smps7";
> > +						regulator-min-microvolt = <600000>;
> > +						regulator-max-microvolt = <1310000>;
> > +						regulator-always-on;
> > +						regulator-boot-on;
> > +					};
> > +
> > +				smps8_reg: smps8 {
> > +						/* VDD_IVAHD */
> > +						regulator-name = "smps8";
> > +						regulator-min-microvolt = < 600000>;
> > +						regulator-max-microvolt = <1310000>;
> > +						regulator-always-on;
> > +						regulator-boot-on;
> > +					};
> > +
> > +				smps9_reg: smps9 {
> > +						/* VDD_1V8 */
> > +						regulator-name = "smps9";
> > +						regulator-min-microvolt = <1800000>;
> > +						regulator-max-microvolt = <1800000>;
> > +						regulator-always-on;
> > +						regulator-boot-on;
> > +					};
> > +
> > +				ldo1_reg: ldo1 {
> > +						/* LDO1_OUT --> SDIO  */
> > +						regulator-name = "ldo1";
> > +						regulator-min-microvolt = <1800000>;
> > +						regulator-max-microvolt = <3300000>;
> > +					};
> > +
> > +				ldo2_reg: ldo2 {
> > +						/* VDD_RTCIO */
> > +						regulator-name = "ldo2";
> > +						regulator-min-microvolt = <3300000>;
> > +						regulator-max-microvolt = <3300000>;
> > +						regulator-always-on;
> > +						regulator-boot-on;
> > +					};
> > +
> > +				ldo3_reg: ldo3 {
> > +						/* VDDA_1V8 PHYs */
> > +						regulator-name = "ldo3";
> > +						regulator-min-microvolt = <1800000>;
> > +						regulator-max-microvolt = <1800000>;
> > +					};
> > +
> > +				ldo9_reg: ldo9 {
> > +						/* VDD_RTC */
> > +						regulator-name = "ldo9";
> > +						regulator-min-microvolt = <1000000>;
> > +						regulator-max-microvolt = <1000000>;
> > +						regulator-boot-on;
> > +						regulator-always-on;
> > +					};
> > +
> > +				ldoln_reg: ldoln {
> > +						/* VDDA_1v8: PLLs */
> > +						regulator-name = "ldoln";
> > +						regulator-min-microvolt = <1800000>;
> > +						regulator-max-microvolt = <1800000>;
> > +						regulator-always-on;
> > +						regulator-boot-on;
> > +					};
> > +
> > +				ldousb_reg: ldousb {
> > +						/* VDDA_3V_USB: VDDA_USBHS33 */
> > +						regulator-name = "ldousb";
> > +						regulator-min-microvolt = <3250000>;
> > +						regulator-max-microvolt = <3250000>;
> > +						regulator-always-on;
> > +						regulator-boot-on;
> > +					};
> > +
> > +				};
> > +			};
> > +		};
> Who are using these LDOs? Example SDIO LDO should be linked up with
> MMC instance, no? how about the PLLs and PHYs?

Linking up will be part of the respective drivers i guess. This patch
adds all the nodes similar to what we have in Palmas.

> >   };
> >   
> >   &i2c2 {

Regards,
Keerthy
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/