Re: Excess dmesg output from ACPIPHP on boot (was: Re: [PATCH25/30] ACPI / hotplug / PCI: Check for new devices on enabled slots)

[Alex Williamson]

On Fri, 2013-09-06 at 00:40 +0200, Rafael J. Wysocki wrote:
> On Thursday, September 05, 2013 04:17:25 PM Alex Williamson wrote:
> > On Thu, 2013-09-05 at 23:39 +0200, Rafael J. Wysocki wrote:
> > > On Thursday, September 05, 2013 09:44:26 PM Rafael J. Wysocki wrote:
> > > > On Thursday, September 05, 2013 08:21:41 AM Alex Williamson wrote:
> > > 
> > > [...]
> > > 
> > > > > > 
> > > > > > [   18.288122] pci 0000:00:00.0: no hotplug settings from platform
> > > > > > [   18.288127] pcieport 0000:00:01.0: no hotplug settings from platform
> > > > > > [   18.288142] pci 0000:01:00.0: no hotplug settings from platform
> > > > > > [   18.288157] pci 0000:01:00.1: no hotplug settings from platform
> > > > > > [   18.288162] pcieport 0000:00:03.0: no hotplug settings from platform
> > > > > > [   18.288176] pci 0000:02:00.0: no hotplug settings from platform
> > > > > > [   18.288190] pci 0000:02:00.1: no hotplug settings from platform
> > > > > > [   18.288195] pcieport 0000:00:07.0: no hotplug settings from platform
> > > > > > [   18.288209] pci 0000:03:00.0: no hotplug settings from platform
> > > > > > [   18.288224] pci 0000:03:00.1: no hotplug settings from platform
> > > > > > [   18.288228] pci 0000:00:14.0: no hotplug settings from platform
> > > > > > [   18.288233] pci 0000:00:14.1: no hotplug settings from platform
> > > > > > [   18.288237] pci 0000:00:14.2: no hotplug settings from platform
> > > > > > [   18.288242] pci 0000:00:16.0: no hotplug settings from platform
> > > > > > [   18.288247] pci 0000:00:16.1: no hotplug settings from platform
> > > > > > [   18.288251] pci 0000:00:16.2: no hotplug settings from platform
> > > > > > [   18.288256] pci 0000:00:16.3: no hotplug settings from platform
> > > > > > [   18.288260] pci 0000:00:16.4: no hotplug settings from platform
> > > > > > [   18.288265] pci 0000:00:16.5: no hotplug settings from platform
> > > > > > [   18.288269] pci 0000:00:16.6: no hotplug settings from platform
> > > > > > [   18.288274] pci 0000:00:16.7: no hotplug settings from platform
> > > > > > [   18.288278] pci 0000:00:1a.0: no hotplug settings from platform
> > > > > > [   18.288279] pci 0000:00:1a.0: using default PCI settings
> > > > > > [   18.288292] pci 0000:00:1a.1: no hotplug settings from platform
> > > > > > [   18.288293] pci 0000:00:1a.1: using default PCI settings
> > > > > > [   18.288307] ehci-pci 0000:00:1a.7: no hotplug settings from platform
> > > > > > [   18.288308] ehci-pci 0000:00:1a.7: using default PCI settings
> > > > > > [   18.288322] pci 0000:00:1b.0: no hotplug settings from platform
> > > > > > [   18.288327] pcieport 0000:00:1c.0: no hotplug settings from platform
> > > > > > [   18.288332] pcieport 0000:00:1c.4: no hotplug settings from platform
> > > > > > [   18.288344] pci 0000:05:00.0: no hotplug settings from platform
> > > > > > [   18.288349] pci 0000:00:1d.0: no hotplug settings from platform
> > > > > > [   18.288350] pci 0000:00:1d.0: using default PCI settings
> > > > > > [   18.288360] pci 0000:00:1d.1: no hotplug settings from platform
> > > > > > [   18.288361] pci 0000:00:1d.1: using default PCI settings
> > > > > > [   18.288374] pci 0000:00:1d.2: no hotplug settings from platform
> > > > > > [   18.288374] pci 0000:00:1d.2: using default PCI settings
> > > > > > [   18.288387] pci 0000:00:1d.3: no hotplug settings from platform
> > > > > > [   18.288387] pci 0000:00:1d.3: using default PCI settings
> > > > > > 
> > > > > > The boot is noticeably slower.  What's going to happen on systems that
> > > > > > actually have a significant I/O topology vs my little workstation?
> > > > 
> > > > That depends on how many bus check/device check events they generate on boot.
> > > > 
> > > > My test machines don't generate them during boot at all (even the one with
> > > > a Thunderbolt connector), so I don't see the messages in question during boot
> > > > on any of them.  Mika doesn't see them either I suppose, or he would have told
> > > > me about that before.
> > > > 
> > > > And let's just make it clear that it is not usual or even OK to generate bus
> > > > checks or device checks during boot like this.  And since the changes in
> > > > question have been in linux-next since right after the 3.11 merge window, I
> > > > think that someone would have complained already had that been a common issue.
> > > > 
> > > > Of course, we need to deal with that somehow nevertheless. :-)
> > > > 
> > > > > Just to give you an idea:
> > > > > 
> > > > > CONFIG_HOTPLUG_PCI_ACPI=y
> > > > > 
> > > > > $ dmesg | wc
> > > > >   5697  49935 384368
> > > > > 
> > > > > $ dmesg | tail --lines=1
> > > > > [   53.137123] Ebtables v2.0 registered
> > > > > 
> > > > > -- vs --
> > > > > 
> > > > > # CONFIG_HOTPLUG_PCI_ACPI is not set
> > > > > 
> > > > > $ dmesg | wc
> > > > >  1053  9176 71652
> > > > > 
> > > > > $dmesg | tail --lines=1
> > > > > [   28.917220] Ebtables v2.0 registered
> > > > > 
> > > > > So it spews out 5x more output with acpiphp enabled and takes and extra
> > > > > 24s to boot (nearly 2x).  Not good.
> > > > 
> > > > The "no hotplug settings from platform" message is from pci_configure_slot().
> > > > I think the messages you're seeing are from the call to it in
> > > > acpiphp_set_hpp_values() which is called by enable_slot().
> > > > 
> > > > There, I think, we can simply check the return value of pci_scan_slot() and
> > > > if that is 0 (no new devices), we can just skip everything under the call to
> > > > __pci_bus_assign_resources().
> > > > 
> > > > However, we can't skip the scanning of bridges, if any, because there may be
> > > > new devices below them and I guess that's what takes so much time on your
> > > > machine.
> > > 
> > > OK, one piece is missing.  We may need to evaluate _OSC after handling each
> > > event to let the platform know the status.
> > > 
> > > Can you please check if the appended patch makes any difference (with the
> > > previous fix applied, of course)?
> > > 
> > > If fact, it is two patches combined.  One of them optimizes enable_slot()
> > > slightly and the other adds the missing _OSC evaluation.
> > 
> > Better, still double the output:
> > 
> > $ dmesg | wc
> >    2169   19047  152710
> 
> I see.
> 
> What about the timing?

~40s below vs ~29s for acpiphp config'd out above.

> > $ dmesg | tail --lines=1
> > [   39.980918] Ebtables v2.0 registered
> > 
> > Here's another interesting stat:
> > 
> > $ dmesg | colrm 1 15 | sort | uniq -c | sort -nr | head --lines=25
> >      73 pci 0000:00:1f.0: BAR 13: [io  0x1000-0x107f] has bogus alignment
> >      73 pci 0000:00:1e.0: PCI bridge to [bus 06]
> >      64 pci 0000:00:1e.0:   bridge window [mem 0x81100000-0x812fffff 64bit pref]
> >      64 pci 0000:00:1e.0:   bridge window [mem 0x80f00000-0x810fffff]
> >      64 pci 0000:00:1e.0:   bridge window [io  0x7000-0x7fff]
> >      38 pci 0000:00:1c.4: PCI bridge to [bus 05]
> >      38 pci 0000:00:1c.4:   bridge window [mem 0xf4f00000-0xf4ffffff]
> >      38 pci 0000:00:1c.0: PCI bridge to [bus 04]
> >      38 pci 0000:00:07.0: PCI bridge to [bus 03]
> >      38 pci 0000:00:07.0:   bridge window [mem 0xf2000000-0xf40fffff]
> >      38 pci 0000:00:07.0:   bridge window [mem 0xe0000000-0xf1ffffff 64bit pref]
> >      38 pci 0000:00:07.0:   bridge window [io  0x4000-0x4fff]
> >      38 pci 0000:00:03.0: PCI bridge to [bus 02]
> >      38 pci 0000:00:03.0:   bridge window [mem 0xf4e00000-0xf4efffff]
> >      38 pci 0000:00:03.0:   bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
> >      38 pci 0000:00:03.0:   bridge window [io  0x3000-0x3fff]
> >      38 pci 0000:00:01.0: PCI bridge to [bus 01]
> >      38 pci 0000:00:01.0:   bridge window [mem 0xf4100000-0xf4bfffff]
> >      38 pci 0000:00:01.0:   bridge window [io  0x2000-0x2fff]
> >      37 pci 0000:00:1c.4:   bridge window [mem 0x80c00000-0x80dfffff 64bit pref]
> >      37 pci 0000:00:1c.4:   bridge window [io  0x6000-0x6fff]
> >      37 pci 0000:00:1c.0:   bridge window [mem 0x80a00000-0x80bfffff 64bit pref]
> >      37 pci 0000:00:1c.0:   bridge window [mem 0x80800000-0x809fffff]
> >      37 pci 0000:00:1c.0:   bridge window [io  0x5000-0x5fff]
> >      36 pci 0000:00:01.0:   bridge window [mem 0x80000000-0x807fffff 64bit pref]
> > 
> > This is nearly the entire difference, just 25 lines repeated over and
> > over.
> 
> Well, this is the bridge sizing I talked about previously.  We still get
> apparently spurious bus check/device check events and they trigger bridge
> scans.
> 
> I'm not sure what to do about that and I wonder whether or not this is
> reproducible on any other machines you can test.

I can try it on a couple other systems, but probably not until tomorrow.

> Can you please change dbg() to pr_info() under ACPI_NOTIFY_BUS_CHECK and
> ACPI_NOTIFY_DEVICE_CHECK in hotplug_event() (acpiphp_glue.c), grep the boot
> dmesg log for "check notify" and send the result?  I'm wondering what's
> going on there.

$ dmesg | grep "check notify"
[    1.633228] hotplug_event: Device check notify on \_SB_.PCI0.PEX2
[    2.472004] hotplug_event: Device check notify on \_SB_.PCI0.PEX3
[    2.477288] hotplug_event: Device check notify on \_SB_.PCI0.PEX4
[    2.482571] hotplug_event: Device check notify on \_SB_.PCI0.PEX5
[    2.482579] hotplug_event: Device check notify on \_SB_.PCI0.PEX6
[    8.204953] hotplug_event: Device check notify on \_SB_.PCI0.PEX2
[    8.209632] hotplug_event: Device check notify on \_SB_.PCI0.PEX3
[    8.214272] hotplug_event: Device check notify on \_SB_.PCI0.PEX4
[    8.218894] hotplug_event: Device check notify on \_SB_.PCI0.PEX5
[    8.218901] hotplug_event: Device check notify on \_SB_.PCI0.PEX6

Thanks,
Alex

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/