[PATCH v8 2/8] usb: phy: omap: Add new device types and remove omap_control_usb3_phy_power()

[Roger Quadros]

Add support for new device types and in the process rid of "ti,type"
device tree property. The correct type of device will be determined
from the compatible string instead.

Introduce a compatible string for each device type. At the moment
we support 4 types OTGHS, USB2, PIPE3 (e.g. USB3) and DRA7USB2.

Update DT binding information to reflect these changes.

Also get rid of omap_control_usb3_phy_power(). Just one function
i.e. omap_control_usb_phy_power() will now take care of all PHY types.

Signed-off-by: Roger Quadros <rogerq@xxxxxx>
---
 Documentation/devicetree/bindings/usb/omap-usb.txt |   30 ++--
 drivers/usb/phy/phy-omap-control.c                 |  173 +++++++++++--------
 drivers/usb/phy/phy-omap-usb3.c                    |    6 +-
 include/linux/usb/omap_control_usb.h               |   24 ++--
 4 files changed, 130 insertions(+), 103 deletions(-)

diff --git a/Documentation/devicetree/bindings/usb/omap-usb.txt b/Documentation/devicetree/bindings/usb/omap-usb.txt
index 661cb06..9add35c 100644
--- a/Documentation/devicetree/bindings/usb/omap-usb.txt
+++ b/Documentation/devicetree/bindings/usb/omap-usb.txt
@@ -83,22 +83,22 @@ omap_dwc3 {
 OMAP CONTROL USB
 
 Required properties:
- - compatible: Should be "ti,omap-control-usb"
+ - compatible: Should be one of
+ "ti,control-phy-otghs" - if it has otghs_control mailbox register as on OMAP4.
+ "ti,control-phy-usb2" - if it has Power down bit in control_dev_conf register
+			e.g. USB2_PHY on OMAP5.
+ "ti,control-phy-pipe3" - if it has DPLL and individual Rx & Tx power control
+			e.g. USB3 PHY and SATA PHY on OMAP5.
+ "ti,control-phy-dra7usb2" - if it has power down register like USB2 PHY on
+			DRA7 platform.
  - reg : Address and length of the register set for the device. It contains
-   the address of "control_dev_conf" and "otghs_control" or "phy_power_usb"
-   depending upon omap4 or omap5.
- - reg-names: The names of the register addresses corresponding to the registers
-   filled in "reg".
- - ti,type: This is used to differentiate whether the control module has
-   usb mailbox or usb3 phy power. omap4 has usb mailbox in control module to
-   notify events to the musb core and omap5 has usb3 phy power register to
-   power on usb3 phy. Should be "1" if it has mailbox and "2" if it has usb3
-   phy power.
+   the address of "otghs_control" for control-phy-otghs or "power" register
+   for other types.
+ - reg-names: should be "otghs_control" control-phy-otghs and "power" for
+   other types.
 
 omap_control_usb: omap-control-usb@4a002300 {
-	compatible = "ti,omap-control-usb";
-	reg = <0x4a002300 0x4>,
-	      <0x4a00233c 0x4>;
-	reg-names = "control_dev_conf", "otghs_control";
-	ti,type = <1>;
+	compatible = "ti,control-phy-otghs";
+	reg = <0x4a00233c 0x4>;
+	reg-names = "otghs_control";
 };
diff --git a/drivers/usb/phy/phy-omap-control.c b/drivers/usb/phy/phy-omap-control.c
index 9772592..1c8a7c5 100644
--- a/drivers/usb/phy/phy-omap-control.c
+++ b/drivers/usb/phy/phy-omap-control.c
@@ -20,6 +20,7 @@
 #include <linux/platform_device.h>
 #include <linux/slab.h>
 #include <linux/of.h>
+#include <linux/of_device.h>
 #include <linux/err.h>
 #include <linux/io.h>
 #include <linux/clk.h>
@@ -46,61 +47,70 @@ struct device *omap_get_control_dev(void)
 EXPORT_SYMBOL_GPL(omap_get_control_dev);
 
 /**
- * omap_control_usb3_phy_power - power on/off the serializer using control
- *	module
+ * omap_control_usb_phy_power - power on/off the phy using control module reg
  * @dev: the control module device
- * @on: 0 to off and 1 to on based on powering on or off the PHY
- *
- * usb3 PHY driver should call this API to power on or off the PHY.
+ * @on: 0 or 1, based on powering on or off the PHY
  */
-void omap_control_usb3_phy_power(struct device *dev, bool on)
+void omap_control_usb_phy_power(struct device *dev, int on)
 {
 	u32 val;
 	unsigned long rate;
-	struct omap_control_usb	*control_usb = dev_get_drvdata(dev);
+	struct omap_control_usb	*control_usb;
 
-	if (control_usb->type != OMAP_CTRL_DEV_TYPE2)
+	if (IS_ERR(dev) || !dev) {
+		pr_err("%s: invalid device\n", __func__);
 		return;
+	}
 
-	rate = clk_get_rate(control_usb->sys_clk);
-	rate = rate/1000000;
-
-	val = readl(control_usb->phy_power);
-
-	if (on) {
-		val &= ~(OMAP_CTRL_USB_PWRCTL_CLK_CMD_MASK |
-			OMAP_CTRL_USB_PWRCTL_CLK_FREQ_MASK);
-		val |= OMAP_CTRL_USB3_PHY_TX_RX_POWERON <<
-			OMAP_CTRL_USB_PWRCTL_CLK_CMD_SHIFT;
-		val |= rate << OMAP_CTRL_USB_PWRCTL_CLK_FREQ_SHIFT;
-	} else {
-		val &= ~OMAP_CTRL_USB_PWRCTL_CLK_CMD_MASK;
-		val |= OMAP_CTRL_USB3_PHY_TX_RX_POWEROFF <<
-			OMAP_CTRL_USB_PWRCTL_CLK_CMD_SHIFT;
+	control_usb = dev_get_drvdata(dev);
+	if (!control_usb) {
+		dev_err(dev, "%s: invalid control usb device\n", __func__);
+		return;
 	}
 
-	writel(val, control_usb->phy_power);
-}
-EXPORT_SYMBOL_GPL(omap_control_usb3_phy_power);
+	if (control_usb->type == OMAP_CTRL_TYPE_OTGHS)
+		return;
 
-/**
- * omap_control_usb_phy_power - power on/off the phy using control module reg
- * @dev: the control module device
- * @on: 0 or 1, based on powering on or off the PHY
- */
-void omap_control_usb_phy_power(struct device *dev, int on)
-{
-	u32 val;
-	struct omap_control_usb	*control_usb = dev_get_drvdata(dev);
+	val = readl(control_usb->power);
+
+	switch (control_usb->type) {
+	case OMAP_CTRL_TYPE_USB2:
+		if (on)
+			val &= ~OMAP_CTRL_DEV_PHY_PD;
+		else
+			val |= OMAP_CTRL_DEV_PHY_PD;
+		break;
 
-	val = readl(control_usb->dev_conf);
+	case OMAP_CTRL_TYPE_PIPE3:
+		rate = clk_get_rate(control_usb->sys_clk);
+		rate = rate/1000000;
+
+		if (on) {
+			val &= ~(OMAP_CTRL_USB_PWRCTL_CLK_CMD_MASK |
+					OMAP_CTRL_USB_PWRCTL_CLK_FREQ_MASK);
+			val |= OMAP_CTRL_USB3_PHY_TX_RX_POWERON <<
+				OMAP_CTRL_USB_PWRCTL_CLK_CMD_SHIFT;
+			val |= rate << OMAP_CTRL_USB_PWRCTL_CLK_FREQ_SHIFT;
+		} else {
+			val &= ~OMAP_CTRL_USB_PWRCTL_CLK_CMD_MASK;
+			val |= OMAP_CTRL_USB3_PHY_TX_RX_POWEROFF <<
+				OMAP_CTRL_USB_PWRCTL_CLK_CMD_SHIFT;
+		}
+		break;
 
-	if (on)
-		val &= ~OMAP_CTRL_DEV_PHY_PD;
-	else
-		val |= OMAP_CTRL_DEV_PHY_PD;
+	case OMAP_CTRL_TYPE_DRA7USB2:
+		if (on)
+			val &= ~OMAP_CTRL_USB2_PHY_PD;
+		else
+			val |= OMAP_CTRL_USB2_PHY_PD;
+		break;
+	default:
+		dev_err(dev, "%s: type %d not recognized\n",
+					__func__, control_usb->type);
+		break;
+	}
 
-	writel(val, control_usb->dev_conf);
+	writel(val, control_usb->power);
 }
 EXPORT_SYMBOL_GPL(omap_control_usb_phy_power);
 
@@ -172,7 +182,7 @@ void omap_control_usb_set_mode(struct device *dev,
 {
 	struct omap_control_usb	*ctrl_usb;
 
-	if (IS_ERR(dev) || control_usb->type != OMAP_CTRL_DEV_TYPE1)
+	if (IS_ERR(dev) || control_usb->type != OMAP_CTRL_TYPE_OTGHS)
 		return;
 
 	ctrl_usb = dev_get_drvdata(dev);
@@ -193,10 +203,45 @@ void omap_control_usb_set_mode(struct device *dev,
 }
 EXPORT_SYMBOL_GPL(omap_control_usb_set_mode);
 
+#ifdef CONFIG_OF
+
+static const enum omap_control_usb_type otghs_data = OMAP_CTRL_TYPE_OTGHS;
+static const enum omap_control_usb_type usb2_data = OMAP_CTRL_TYPE_USB2;
+static const enum omap_control_usb_type pipe3_data = OMAP_CTRL_TYPE_PIPE3;
+static const enum omap_control_usb_type dra7usb2_data = OMAP_CTRL_TYPE_DRA7USB2;
+
+static const struct of_device_id omap_control_usb_id_table[] = {
+	{
+		.compatible = "ti,control-phy-otghs",
+		.data = &otghs_data,
+	},
+	{
+		.compatible = "ti,control-phy-usb2",
+		.data = &usb2_data,
+	},
+	{
+		.compatible = "ti,control-phy-pipe3",
+		.data = &pipe3_data,
+	},
+	{
+		.compatible = "ti,control-phy-dra7usb2",
+		.data = &dra7usb2_data,
+	},
+	{},
+};
+MODULE_DEVICE_TABLE(of, omap_control_usb_id_table);
+#endif
+
+
 static int omap_control_usb_probe(struct platform_device *pdev)
 {
 	struct resource	*res;
-	struct device_node *np = pdev->dev.of_node;
+	const struct of_device_id *of_id;
+
+	of_id = of_match_device(of_match_ptr(omap_control_usb_id_table),
+								&pdev->dev);
+	if (!of_id)
+		return -EINVAL;
 
 	control_usb = devm_kzalloc(&pdev->dev, sizeof(*control_usb),
 		GFP_KERNEL);
@@ -205,36 +250,27 @@ static int omap_control_usb_probe(struct platform_device *pdev)
 		return -ENOMEM;
 	}
 
-	if (np)
-		of_property_read_u32(np, "ti,type", &control_usb->type);
-	else
-		return -EINVAL;	/* We only support DT boot */
-
-	control_usb->dev	= &pdev->dev;
+	control_usb->dev = &pdev->dev;
+	control_usb->type = *(enum omap_control_usb_type *)of_id->data;
 
-	res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
-		"control_dev_conf");
-	control_usb->dev_conf = devm_ioremap_resource(&pdev->dev, res);
-	if (IS_ERR(control_usb->dev_conf))
-		return PTR_ERR(control_usb->dev_conf);
-
-	if (control_usb->type == OMAP_CTRL_DEV_TYPE1) {
+	if (control_usb->type == OMAP_CTRL_TYPE_OTGHS) {
 		res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
 			"otghs_control");
 		control_usb->otghs_control = devm_ioremap_resource(
 			&pdev->dev, res);
 		if (IS_ERR(control_usb->otghs_control))
 			return PTR_ERR(control_usb->otghs_control);
-	}
-
-	if (control_usb->type == OMAP_CTRL_DEV_TYPE2) {
+	} else {
 		res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
-			"phy_power_usb");
-		control_usb->phy_power = devm_ioremap_resource(
-			&pdev->dev, res);
-		if (IS_ERR(control_usb->phy_power))
-			return PTR_ERR(control_usb->phy_power);
+				"power");
+		control_usb->power = devm_ioremap_resource(&pdev->dev, res);
+		if (IS_ERR(control_usb->power)) {
+			dev_err(&pdev->dev, "Couldn't get power register\n");
+			return PTR_ERR(control_usb->power);
+		}
+	}
 
+	if (control_usb->type == OMAP_CTRL_TYPE_PIPE3) {
 		control_usb->sys_clk = devm_clk_get(control_usb->dev,
 			"sys_clkin");
 		if (IS_ERR(control_usb->sys_clk)) {
@@ -243,20 +279,11 @@ static int omap_control_usb_probe(struct platform_device *pdev)
 		}
 	}
 
-
 	dev_set_drvdata(control_usb->dev, control_usb);
 
 	return 0;
 }
 
-#ifdef CONFIG_OF
-static const struct of_device_id omap_control_usb_id_table[] = {
-	{ .compatible = "ti,omap-control-usb" },
-	{}
-};
-MODULE_DEVICE_TABLE(of, omap_control_usb_id_table);
-#endif
-
 static struct platform_driver omap_control_usb_driver = {
 	.probe		= omap_control_usb_probe,
 	.driver		= {
diff --git a/drivers/usb/phy/phy-omap-usb3.c b/drivers/usb/phy/phy-omap-usb3.c
index 4e8a040..0824be4 100644
--- a/drivers/usb/phy/phy-omap-usb3.c
+++ b/drivers/usb/phy/phy-omap-usb3.c
@@ -100,7 +100,7 @@ static int omap_usb3_suspend(struct usb_phy *x, int suspend)
 			udelay(1);
 		} while (--timeout);
 
-		omap_control_usb3_phy_power(phy->control_dev, 0);
+		omap_control_usb_phy_power(phy->control_dev, 0);
 
 		phy->is_suspended	= 1;
 	} else if (!suspend && phy->is_suspended) {
@@ -189,7 +189,7 @@ static int omap_usb3_init(struct usb_phy *x)
 	if (ret)
 		return ret;
 
-	omap_control_usb3_phy_power(phy->control_dev, 1);
+	omap_control_usb_phy_power(phy->control_dev, 1);
 
 	return 0;
 }
@@ -245,7 +245,7 @@ static int omap_usb3_probe(struct platform_device *pdev)
 		return -ENODEV;
 	}
 
-	omap_control_usb3_phy_power(phy->control_dev, 0);
+	omap_control_usb_phy_power(phy->control_dev, 0);
 	usb_add_phy_dev(&phy->phy);
 
 	platform_set_drvdata(pdev, phy);
diff --git a/include/linux/usb/omap_control_usb.h b/include/linux/usb/omap_control_usb.h
index e2416b4..61b889a 100644
--- a/include/linux/usb/omap_control_usb.h
+++ b/include/linux/usb/omap_control_usb.h
@@ -19,16 +19,23 @@
 #ifndef __OMAP_CONTROL_USB_H__
 #define __OMAP_CONTROL_USB_H__
 
+enum omap_control_usb_type {
+	OMAP_CTRL_TYPE_OTGHS = 1,	/* Mailbox OTGHS_CONTROL */
+	OMAP_CTRL_TYPE_USB2,	/* USB2_PHY, power down in CONTROL_DEV_CONF */
+	OMAP_CTRL_TYPE_PIPE3,	/* PIPE3 PHY, DPLL & seperate Rx/Tx power */
+	OMAP_CTRL_TYPE_DRA7USB2, /* USB2 PHY, power and power_aux e.g. DRA7 */
+};
+
 struct omap_control_usb {
 	struct device *dev;
 
-	u32 __iomem *dev_conf;
 	u32 __iomem *otghs_control;
-	u32 __iomem *phy_power;
+	u32 __iomem *power;
+	u32 __iomem *power_aux;
 
 	struct clk *sys_clk;
 
-	u32 type;
+	enum omap_control_usb_type type;
 };
 
 enum omap_control_usb_mode {
@@ -38,10 +45,6 @@ enum omap_control_usb_mode {
 	USB_MODE_DISCONNECT,
 };
 
-/* To differentiate ctrl module IP having either mailbox or USB3 PHY power */
-#define	OMAP_CTRL_DEV_TYPE1		0x1
-#define	OMAP_CTRL_DEV_TYPE2		0x2
-
 #define	OMAP_CTRL_DEV_PHY_PD		BIT(0)
 
 #define	OMAP_CTRL_DEV_AVALID		BIT(0)
@@ -59,10 +62,11 @@ enum omap_control_usb_mode {
 #define	OMAP_CTRL_USB3_PHY_TX_RX_POWERON	0x3
 #define	OMAP_CTRL_USB3_PHY_TX_RX_POWEROFF	0x0
 
+#define OMAP_CTRL_USB2_PHY_PD		BIT(28)
+
 #if IS_ENABLED(CONFIG_OMAP_CONTROL_USB)
 extern struct device *omap_get_control_dev(void);
 extern void omap_control_usb_phy_power(struct device *dev, int on);
-extern void omap_control_usb3_phy_power(struct device *dev, bool on);
 extern void omap_control_usb_set_mode(struct device *dev,
 	enum omap_control_usb_mode mode);
 #else
@@ -75,10 +79,6 @@ static inline void omap_control_usb_phy_power(struct device *dev, int on)
 {
 }
 
-static inline void omap_control_usb3_phy_power(struct device *dev, int on)
-{
-}
-
 static inline void omap_control_usb_set_mode(struct device *dev,
 	enum omap_control_usb_mode mode)
 {
-- 
1.7.4.1

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/