Re: [RFC] Does PHY UTMI data width belong to DWC2 or PHY binding?

[Kishon Vijay Abraham I]

Hi,

On Wednesday 23 October 2013 08:12 PM, Matt Porter wrote:
> On Tue, Oct 22, 2013 at 04:38:52PM -0500, Rob Herring wrote:
>> On 10/22/2013 06:25 AM, Matt Porter wrote:
>>> On Tue, Oct 22, 2013 at 12:48:29PM +0200, Matthijs Kooijman wrote:
>>>> Hi Kishon,
>>>>
>>>> On Mon, Oct 21, 2013 at 02:57:26PM +0530, Kishon Vijay Abraham I wrote:
>>>>> I think it makes sense to keep the data width property in the dwc2 node itself.
>>>>> I mean it describes how the dwc2 IP is configured in that particular SoC (given
>>>>> that it can be either <8> or <16>).
>>>> If I'm reading the RT3052 datasheet correctly (GHWCFG4 register), the IP
>>>> can be configured for 8, 16 or 8 _and_ 16. In the latter case, the "8
>>>> and 16 supported" would make sense as a property of dwc2 (though this
>>>> value should be autodetectable through GHWCFG4), while the actual 8 or
>>>> 16 supported by the PHY would make sense as property of a phy.
>>>
>>> There would be no value in adding a property for an already detectable
>>> value to dwc2's binding. To be honest, it's pretty much useless
>>> information due to the existence of the "8 and 16" option.
>>>
>>>> Note sure if this is really useful in practice as well, or if just
>>>> setting the actual width to use on dwc2 makes more sense...
>>>
>>> The GHWCFG4 information itself is not useful in practice, as described
>>> in the original thread: https://lkml.org/lkml/2013/10/10/477
>>>
>>> It's certainly useful in practice to have this width property in either
>>> the dwc2 or the phy binding. One can make a case for either. As I
>>> mentioned in the original post, if we put it in the phy binding we'll be
>>> updating the generic phy binding. We'll then need an api added into the
>>> generic phy framework to fetch the width of a phy.
>>>
>>> Both cases are doable and trivial, we just need the canonical decision
>>> from a DT maintainer as to where the property belongs. Given that they
>>> are in ARM ksummit, I'm not expecting to hear anything right this
>>> moment. :)
>>
>> The host can support both, so it is not a property of the host and is a
>> property of the phy. It is no different than what mode a SPI slave
>> requires or whether an i2c slave supports 8 or 10-bit addressing. Those
>> examples are all 1 to many rather than 1 to 1 where it doesn't really
>> matter, but the same logic applies.
> 
> Makes good sense, thanks.
> 
> In this case, given the PHY ownership of width, we can completely avoid
> any DT properties. The generic phy compliant BCM Kona phy driver can
> report via the generic phy framework that it is 8-bit wide. There's no
> support for this type of thing now but it's pretty trivial to add.
> 
> I went ahead and did a quick proof-of-concept that adds a free-form
> phy attributes struct for the generic phy. Given that generic phys can
> be for any transmission technology this could be filled with a jumble
> unrelated and often unpopulated attributes over time. In any case, the
> below patch allows the phy provider to choose to specify utmi_width and
> a controller driver that cares can use phy_get_attrs() to fetch the
> optional phy attributes and use the utmi_width field if applicable.
> 
> Kishon: I'll start a separate thread to discuss what approach you'd like
> to see in the generic phy framework to manage this.
> 
> -Matt
> 
> diff --git a/include/linux/phy/phy.h b/include/linux/phy/phy.h
> index 6d72269..b763d7b 100644
> --- a/include/linux/phy/phy.h
> +++ b/include/linux/phy/phy.h
> @@ -38,6 +38,14 @@ struct phy_ops {
>  };
> 
>  /**
> + * struct phy_attrs - represents phy attributes
> + * @utmi_width: Data path width implemented by UTMI PHY
> + */
> +struct phy_attrs {
> +	int			utmi_width;
> +};
> +
> +/**
>   * struct phy - represents the phy device
>   * @dev: phy device
>   * @id: id of the phy device
> @@ -51,6 +59,7 @@ struct phy {
>  	struct device		dev;
>  	int			id;
>  	const struct phy_ops	*ops;
> +	struct phy_attrs	*attrs;
>  	struct phy_init_data	*init_data;
>  	struct mutex		mutex;
>  	int			init_count;
> @@ -127,6 +136,9 @@ int phy_init(struct phy *phy);
>  int phy_exit(struct phy *phy);
>  int phy_power_on(struct phy *phy);
>  int phy_power_off(struct phy *phy);
> +static inline struct phy_attrs *phy_get_attrs(struct phy *phy) {
> +	return phy->attrs;
> +};

I'd prefer to have phy_set_bus_width and phy_get_bus_width instead.

Thanks
Kishon

>  struct phy *phy_get(struct device *dev, const char *string);
>  struct phy *devm_phy_get(struct device *dev, const char *string);
>  void phy_put(struct phy *phy);
> 

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/