Re: [PATCH RFC 1/4] phy: Add new Exynos5 USB 3.0 PHY driver

[Jingoo Han]

On Tuesday, November 05, 2013 8:13 PM, Jingoo Han wrote:
> On Tuesday, November 05, 2013 6:37 PM, Kamil Debski wrote:
> > On Tuesday, November 05, 2013 8:20 AM, Vivek Gautam wrote:
> > > On Mon, Nov 4, 2013 at 6:42 PM, Kishon Vijay Abraham I <kishon@xxxxxx> wrote:
> > > > On Monday 04 November 2013 03:45 PM, Kamil Debski wrote:
> > > >> On Monday, November 04, 2013 7:55 AM, Kishon Vijay Abraham I wrote:
> > > >>> On Thursday 31 October 2013 01:15 PM, Vivek Gautam wrote:
> > > >>>>
> > > >>>> Add a new driver for the USB 3.0 PHY on Exynos5 series of SoCs.
> > > >>>> The new driver uses the generic PHY framework and will interact
> > > >>>> with
> > > >>>> DWC3 controller present on Exynos5 series of SoCs.
> > > >>>
> > > >>>
> > > >>> In Exynos, you have a single IP that supports both USB3 and USB2
> > > PHY
> > > >>> right? I think that needs to be mentioned here.
> > > >>
> > > >>
> > > >> As far as I know the IP is different.
> > > >
> > > >
> > > > Ok. Sometime back Vivek was mentioning about a single IP for both
> > > USB3
> > > > and USB2. Thought it should be this driver. Anyway thanks for the
> > > clarification.
> > >
> > > Right Kishon, I had mentioned that Exynos5's dwc3 controller have a
> > > single IP for USB2 and USB3 phy.
> > > From what i see, on exynos5 systems the dwc3 controller uses a combo of
> > > usb 2 (utmi+) and usb 3 (pipe 3) phy (with base address starting
> > > 0x12100000).
> > >
> > > Kamil, Tomasz,
> > >
> > > Please correct me if i am wrong.
> >
> > I have the Exynos 5250 documentation and I found two phy register ranges:
> > 1) USB 2.0 PHY having the base address of 0x1213 0000
> > 	Chapter 33. USB 2.0 Host Controller
> > 	Subchapter 33.5.2 Phy Control Register p. 1696
> > 	First register's description is
> > 	"USB2.0 phy control register"
> > 2) USB 3.0 PHY (I guess) with the base address 0x1210 0000
> > 	Chapter 35. USB 3.0 DRD Controller
> > 	Subchapter 35.4.6 PHY Control Register p. 1872
> >
> > Jingoo, could you comment on the above? You may know more than we do :)
> 
> Hi Kamil,
> 
> Thank you for trusting me. :-)
> I just asked my validation engineer about 5250 USB PHY.
> As I know, she has the best knowledge about Samsung SoC USB hardware.
> She said that there are 2 PHY controllers such as USB 2.0 PHY, USB 3.0 PHY.
> 
>   1) USB2.0 PHY: USB2.0 HOST, USB2.0 Device
>   2) USB3.0 PHY: USB3.0 DRD (3.0 HOST & 3.0 Device)
> 
> > In addition, I have a question to you Vivek - does your USB 3.0
> > PHY support both host and device?
> 
> According to her, USB3.0 PHY can support both 3.0 Host and 3.0 Device.
> Thank you.

In addition to this,

Vivek's comment is also right. :-)
A few minutes ago, I asked one of my USB S/W engineers.

USB3.0 PHY consists of two blocks such as 3.0 block and 2.0 block.
This USB3.0 PHY can support UTMI+ and PIPE3 interface for 3.0 block
and 2.0 block, respectively.

Conclusion:

   1) USB2.0 PHY: USB2.0 HOST, USB2.0 Device
                       Base address: 0x1213 0000

   2) USB3.0 PHY: USB3.0 DRD (3.0 HOST & 3.0 Device)
                       Base address: 0x1210 0000
                       2.0 block(UTMI+) & 3.0 block(PIPE3)


Best regards,
Jingoo Han

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/