[PATCH 1/7] ARM: ux500: Remove legacy ATAG SSP support

[Lee Jones]

This hasn't been used since we converted the platform to DT only.

Signed-off-by: Lee Jones <lee.jones@xxxxxxxxxx>
---
 arch/arm/mach-ux500/board-mop500.c | 30 ------------------------------
 arch/arm/mach-ux500/board-mop500.h |  1 -
 2 files changed, 31 deletions(-)

diff --git a/arch/arm/mach-ux500/board-mop500.c b/arch/arm/mach-ux500/board-mop500.c
index 514d40b..d552163 100644
--- a/arch/arm/mach-ux500/board-mop500.c
+++ b/arch/arm/mach-ux500/board-mop500.c
@@ -46,33 +46,3 @@ struct ab8500_platform_data ab8500_platdata = {
 	.irq_base	= MOP500_AB8500_IRQ_BASE,
 	.regulator	= &ab8500_regulator_plat_data,
 };
-
-#ifdef CONFIG_STE_DMA40
-static struct stedma40_chan_cfg ssp0_dma_cfg_rx = {
-	.mode = STEDMA40_MODE_LOGICAL,
-	.dir = DMA_DEV_TO_MEM,
-	.dev_type = DB8500_DMA_DEV8_SSP0,
-};
-
-static struct stedma40_chan_cfg ssp0_dma_cfg_tx = {
-	.mode = STEDMA40_MODE_LOGICAL,
-	.dir = DMA_MEM_TO_DEV,
-	.dev_type = DB8500_DMA_DEV8_SSP0,
-};
-#endif
-
-struct pl022_ssp_controller ssp0_plat = {
-	.bus_id = 0,
-#ifdef CONFIG_STE_DMA40
-	.enable_dma = 1,
-	.dma_filter = stedma40_filter,
-	.dma_rx_param = &ssp0_dma_cfg_rx,
-	.dma_tx_param = &ssp0_dma_cfg_tx,
-#else
-	.enable_dma = 0,
-#endif
-	/* on this platform, gpio 31,142,144,214 &
-	 * 224 are connected as chip selects
-	 */
-	.num_chipselect = 5,
-};
diff --git a/arch/arm/mach-ux500/board-mop500.h b/arch/arm/mach-ux500/board-mop500.h
index 511d6fe..d48e866 100644
--- a/arch/arm/mach-ux500/board-mop500.h
+++ b/arch/arm/mach-ux500/board-mop500.h
@@ -87,7 +87,6 @@ extern struct msp_i2s_platform_data msp0_platform_data;
 extern struct msp_i2s_platform_data msp1_platform_data;
 extern struct msp_i2s_platform_data msp2_platform_data;
 extern struct msp_i2s_platform_data msp3_platform_data;
-extern struct pl022_ssp_controller ssp0_plat;
 
 void __init mop500_pinmaps_init(void);
 void __init snowball_pinmaps_init(void);
-- 
1.8.1.2

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/