Re: [PATCH v6 3/3] mfd: max14577: Add device tree bindings document

[Lee Jones]

> Add document describing device tree bindings for MAX14577 MFD driver.
> 
> Signed-off-by: Krzysztof Kozlowski <k.kozlowski@xxxxxxxxxxx>
> Signed-off-by: Kyungmin Park <kyungmin.park@xxxxxxxxxxx>
> ---
>  Documentation/devicetree/bindings/mfd/max14577.txt |   48 ++++++++++++++++++++
>  1 file changed, 48 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/mfd/max14577.txt
> 
> diff --git a/Documentation/devicetree/bindings/mfd/max14577.txt b/Documentation/devicetree/bindings/mfd/max14577.txt
> new file mode 100644
> index 000000000000..f4fd16360b6b
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mfd/max14577.txt
> @@ -0,0 +1,48 @@
> +MAXIM MAX14577 multi-function device

Why is Maxim capitalised in such a way?

If you're going to use the term Multi-Function Device, please
capitalise it.

> +MAX14577 is a Multi-function device with Micro-USB Interface Circuit, Li+

Same here.

> +Battery Charger and SFOUT LDO output for powering USB devices. It is
> +interfaced to host controller using I2C.
> +
> +Required properties:
> +- compatible : Must be "maxim,max14577".
> +- reg : I2C slave address for the max14577 chip.
> +- interrupts : IRQ line for the max14577 chip.
> +- interrupt-parent :  The parent interrupt controller.
> +
> +Optional nodes:
> +- regulators :
> +  Required child node properties:
> +  - compatible : "maxim,max14577-regulator"
> +
> +  Optional child nodes:
> +    Each child node representing a regulator, following standard regulator
> +    bindings. Valid names for a regulator are: "CHARGER" and "SAFEOUT".
> +    The SAFEOUT is a constant voltage regulator so there is no need

s/constant/fixed

> +    to specify voltages for it.

The whole of the "Optional nodes" explaination isn't as clear as it
could otherwise be. 

> +	[*] refer Documentation/devicetree/bindings/regulator/regulator.txt
> +
> +Example:
> +	max14577@25 {
> +		compatible = "maxim,max14577";
> +		reg = <0x25>;
> +		interrupt-parent = <&gpx1>;
> +		interrupts = <5 0>;

I'm gussing this is IRQ5 and the 0 is flags? If so, please use
#defines for the flags.

> +		regulators {
> +			compatible = "maxim,max14577-regulator";
> +
> +			safeout_reg: safeout@1 {

The name of the node (not the label:safeout_reg) usually depicts the
type of device, so 'regulator@0' and 'regulator@1'. However, I'm
unsure how this works when these nodes are encapsulated by an
overarching 'regulators' parent node.

Perhaps Mark can answer this?

> +				regulator-compatible = "SAFEOUT";
> +				regulator-name = "SAFEOUT";
> +			};
> +			charger_reg: charger@0 {
> +				regulator-compatible = "CHARGER";
> +				regulator-name = "CHARGER";
> +				regulator-min-microamp = <90000>;
> +				regulator-max-microamp = <950000>;
> +				regulator-boot-on;
> +			};
> +		};
> +	};

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org â Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/