Re: [PATCH 2/2] memory: ti-aemif: add bindings for AEMIF driver

From: ivan.khoronzhuk
Date: Tue Dec 10 2013 - 05:41:55 EST


On 12/10/2013 01:09 AM, Kumar Gala wrote:
>
> On Nov 26, 2013, at 10:27 AM, Grygorii Strashko <grygorii.strashko@xxxxxx> wrote:
>
>> On 11/22/2013 11:04 PM, Kumar Gala wrote:
>>>
>>> On Nov 20, 2013, at 9:46 AM, Ivan Khoronzhuk <ivan.khoronzhuk@xxxxxx> wrote:
>>>
>>>> Add bindings for AEMIF controller drivers/memory/ti-aemif.c
>>>>
>>>
>>> Binding shouldn’t normally refer to code.
>>>
>>> Just saying something like:
>>>
>>> Adding binging for TI Async External Memory Interface (AEMIF) controller.
>>>
>>>
>>>> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@xxxxxx>
>>>> ---
>>>> .../bindings/memory-controllers/ti-aemif.txt | 198 ++++++++++++++++++++
>>>> 1 file changed, 198 insertions(+)
>>>> create mode 100644 Documentation/devicetree/bindings/memory-controllers/ti-aemif.txt
>>>>
>>>> diff --git a/Documentation/devicetree/bindings/memory-controllers/ti-aemif.txt b/Documentation/devicetree/bindings/memory-controllers/ti-aemif.txt
>>>> new file mode 100644
>>>> index 0000000..be0c0cb
>>>> --- /dev/null
>>>> +++ b/Documentation/devicetree/bindings/memory-controllers/ti-aemif.txt
>>>> @@ -0,0 +1,198 @@
>>>> +* Device tree bindings for Texas instruments AEMIF controller
>>>> +
>>>> +Th Async External Memory Interface (EMIF16/AEMIF) controller is intended to
>>>
>>> The?
>>>
>>>> +provide a glue-less interface to a variety of asynchronous memory devices like
>>>> +ASRA M, NOR and NAND memory. A total of 256M bytes of any of these memories
>>>> +can be accessed at any given time via four chip selects with 64M byte access
>>>> +per chip select. Synchronous memories such as DDR1 SD RAM, SDR SDRAM
>>>> +and Mobile SDR are not supported.
>>>> +
>>>> +Documentation:
>>>> +Davinci DM646x - http://www.ti.com/lit/ug/sprueq7c/sprueq7c.pdf
>>>> +OMAP-L138 - http://www.ti.com/lit/ug/spruh77a/spruh77a.pdf
>>>> +Kestone - http://www.ti.com/lit/ug/sprugz3a/sprugz3a.pdf
>>>> +
>>>> +Required properties:
>>>> +
>>>> +- compatible: "ti,davinci-aemif"
>>>> + "ti,keystone-aemif"
>>>> + "ti,omap-L138-aemif"
>>>> +
>>>> +- #address-cells: Must be 2. The first cell is the memory partition
>>>> + number. The 0 partition is for chip selects. And the
>>>> + second cell is the offset into the partition, for the 0
>>>> + partition it corresponds to chip select offset.
>>>> +
>>>
>>> Is the first cell just the chip select number?
>>
>> No. It's rather memory range/partition number. Now there are 2 partitions:
>> - control partition which is common for all CS interfaces
>> - CS-specific partition/range
>> (this one can be splitted according to specific SoC requirement)
>>
>> As per Keystone TCI6638K2K
>> Datasheet http://www.ti.com/lit/ds/sprs836d/sprs836d.pdf:
>>
>> 1) the memory range 0 will be from 0x30000000 size 0x10000000:
>> 00 3000 0000 - 00 33FF FFFF 64M EMIF16 CE0
>> 00 3400 0000 - 00 37FF FFFF 64M EMIF16 CE1
>> 00 3800 0000 - 00 3BFF FFFF 64M EMIF16 CE2
>> 00 3C00 0000 - 00 3FFF FFFF 64M EMIF16 CE3
>>
>> 2) the memory range 1:
>> 00 2100 0A00 - 00 2100 0AFF 256 AEMIF Config
>>
>> And AEMIF node contains definition:
>> ranges = <0 0 0x30000000 0x10000000
>> 1 0 0x21000A00 0x0000100>;
>>
>>
>> Child node has (nand):
>> reg = <0 0 0x4000000 (cs0)
>> - or - 0 0x4000000 0x4000000 (cs1)
>> - or - 0 0x8000000 0x4000000 (cs2)
>> - or - 0 0xC000000 0x4000000 (cs3)
>> - and -
>> 1 0 0x0000100>; (for all cs)
>>
>> For example for cs2 child node the resulting mem range 0 will be calculated as
>>
>> from: 0x30000000 + (0 0x8000000 - 0 0)
>> size: 0x4000000
>>
>> We don't encode CS number in reg/ranges, because it will allow simply change
>> AEMIF DT definitions depending on each SoC
>> (AEMIF CS memory range can be continuous as above or not, if not - additional
>> range/partition can be added and child device can select the proper one).
>
> This is quite confusing. I think the ranges property needs far more description as part of the top level controller node. It spec out what the various fields are in the ranges property.
>

Yes, you are right, description is quite poor. I should describe it more clearly

--
Regards,
Ivan Khoronzhuk
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/