Re: [PATCH v2] Documentation: Add MDIO bus node to PHY binding document

[Florian Fainelli]

Le mercredi 13 novembre 2013, 15:07:49 Jonas Jensen a écrit :
> Add MDIO bus node segment and update the example,
> allowing trivial bindings to break out boilerplate.
> 
> Signed-off-by: Jonas Jensen <jonas.jensen@xxxxxxxxx>
> ---
> 
> Notes:
>     Thanks Mark,
> 
>     This should have the changes from your comments. It also adds optional
> properties "compatible" and "reg", were those overlooked or left out
> intentionally?

Please CC netdev@xxxxxxxxxxxxxxx too as there might be some interest from 
networking folks not actively following devicetree-discuss.

This does looks good to me, there is not much to be said to the point where I 
wonder if this even deserves such an example, but it cannot hurt.

> 
>     Changes since v1:
> 
>     1. reformat "MDIO bus node" description and add, node name should be
> "mdio" 2. reformat property descriptions, describe what the cells represent
> 3. add optional properties
>     4. add a description after "PHY nodes"
> 
>     Applies to next-20131113
> 
>  Documentation/devicetree/bindings/net/phy.txt | 48
> ++++++++++++++++++++++----- 1 file changed, 40 insertions(+), 8
> deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/net/phy.txt
> b/Documentation/devicetree/bindings/net/phy.txt index 7cd18fb..4179a70
> 100644
> --- a/Documentation/devicetree/bindings/net/phy.txt
> +++ b/Documentation/devicetree/bindings/net/phy.txt
> @@ -1,5 +1,26 @@
> +MDIO Bus Nodes
> +
> +An MDIO bus node describes an MDIO bus, and is a container for PHY nodes
> +as described below. An MDIO bus node should be named "mdio".
> +
> +Required properties:
> +
> +- #address-cells = Should be <1>, specifies the number of cells needed
> +  to encode the PHY address
> +- #size-cells = Should be <0>
> +
> +Optional Properties:
> +
> +- compatible : Should contain a specific name for the MDIO bus,
> +  if known, followed by "-mdio"
> +- reg : Should contain register location and length
> +
> +
>  PHY nodes
> 
> +Describes the PHY chip. A MAC connecting the PHY may use a phandle to
> +this node.
> +
>  Required properties:
> 
>   - device_type : Should be "ethernet-phy"
> @@ -23,13 +44,24 @@ Optional Properties:
>    assume clause 22. The compatible list may also contain other
>    elements.
> 
> +
>  Example:
> 
> -ethernet-phy@0 {
> -	compatible = "ethernet-phy-ieee802.3-c22";
> -	linux,phandle = <2452000>;
> -	interrupt-parent = <40000>;
> -	interrupts = <35 1>;
> -	reg = <0>;
> -	device_type = "ethernet-phy";
> -};
> +mdio {
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +
> +	ethernet-phy@0 {
> +		device_type = "ethernet-phy";
> +		compatible = "...", "ethernet-phy-ieee802.3-c22";
> +		reg = <0>;
> +		interrupts = <24 0>;
> +	}
> +
> +	ethernet-phy@1 {
> +		device_type = "ethernet-phy";
> +		compatible = "...";
> +		reg = <1>;
> +		interrupts = <35 1>;
> +	}
> +}

-- 
Florian
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/