[PATCH 3/4] spi: sunxi: Add Allwinner A31 SPI controller driver
From: Maxime Ripard
Date: Thu Jan 16 2014 - 12:16:40 EST
The Allwinner A31 has a new SPI controller IP compared to the older Allwinner
SoCs.
It supports DMA, but the driver only does PIO for now, and DMA will be
supported eventually.
Signed-off-by: Maxime Ripard <maxime.ripard@xxxxxxxxxxxxxxxxxx>
---
.../devicetree/bindings/spi/spi-sun6i.txt | 23 +
drivers/spi/Makefile | 1 +
drivers/spi/spi-sun6i.c | 463 +++++++++++++++++++++
3 files changed, 487 insertions(+)
create mode 100644 Documentation/devicetree/bindings/spi/spi-sun6i.txt
create mode 100644 drivers/spi/spi-sun6i.c
diff --git a/Documentation/devicetree/bindings/spi/spi-sun6i.txt b/Documentation/devicetree/bindings/spi/spi-sun6i.txt
new file mode 100644
index 0000000..019a05f
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/spi-sun6i.txt
@@ -0,0 +1,23 @@
+Allwinner A31 SPI controller
+
+Required properties:
+- compatible: Should be "allwinner,sun6i-a31-spi".
+- reg: Should contain register location and length.
+- interrupts: Should contain interrupt.
+- clocks: phandle to the clocks feeding the SPI controller. Two are
+ needed:
+ - "ahb": the gated AHB parent clock
+ - "mod": the parent module clock
+- resets: phandle to the reset controller asserting this device in
+ reset
+
+Example:
+
+spi1: spi@01c69000 {
+ compatible = "allwinner,sun6i-a31-spi";
+ reg = <0x01c69000 0x1000>;
+ interrupts = <0 66 4>;
+ clocks = <&ahb1_gates 21>, <&spi1_clk>;
+ clock-names = "ahb", "mod";
+ resets = <&ahb1_rst 21>;
+};
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index ab8d864..b94f43d 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -69,6 +69,7 @@ obj-$(CONFIG_SPI_SH_HSPI) += spi-sh-hspi.o
obj-$(CONFIG_SPI_SH_MSIOF) += spi-sh-msiof.o
obj-$(CONFIG_SPI_SH_SCI) += spi-sh-sci.o
obj-$(CONFIG_SPI_SIRF) += spi-sirf.o
+obj-$(CONFIG_ARCH_SUNXI) += spi-sun6i.o
obj-$(CONFIG_SPI_TEGRA114) += spi-tegra114.o
obj-$(CONFIG_SPI_TEGRA20_SFLASH) += spi-tegra20-sflash.o
obj-$(CONFIG_SPI_TEGRA20_SLINK) += spi-tegra20-slink.o
diff --git a/drivers/spi/spi-sun6i.c b/drivers/spi/spi-sun6i.c
new file mode 100644
index 0000000..92f0343
--- /dev/null
+++ b/drivers/spi/spi-sun6i.c
@@ -0,0 +1,463 @@
+/*
+ * Copyright (C) 2012 - 2014 Allwinner Tech
+ * Pan Nan <pannan@xxxxxxxxxxxxxxxxx>
+ *
+ * Copyright (C) 2014 Maxime Ripard
+ * Maxime Ripard <maxime.ripard@xxxxxxxxxxxxxxxxxx>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/reset.h>
+#include <linux/workqueue.h>
+
+#include <linux/spi/spi.h>
+
+#define SUN6I_FIFO_DEPTH 128
+
+#define SUN6I_GBL_CTL_REG 0x04
+#define SUN6I_GBL_CTL_BUS_ENABLE BIT(0)
+#define SUN6I_GBL_CTL_MASTER BIT(1)
+#define SUN6I_GBL_CTL_TP BIT(7)
+#define SUN6I_GBL_CTL_RST BIT(31)
+
+#define SUN6I_TFR_CTL_REG 0x08
+#define SUN6I_TFR_CTL_CPHA BIT(0)
+#define SUN6I_TFR_CTL_CPOL BIT(1)
+#define SUN6I_TFR_CTL_SPOL BIT(2)
+#define SUN6I_TFR_CTL_CS_MASK 0x3
+#define SUN6I_TFR_CTL_CS(cs) (((cs) & SUN6I_TFR_CTL_CS_MASK) << 4)
+#define SUN6I_TFR_CTL_FBS BIT(12)
+#define SUN6I_TFR_CTL_XCH BIT(31)
+
+#define SUN6I_INT_CTL_REG 0x10
+#define SUN6I_INT_CTL_RF_OVF BIT(8)
+#define SUN6I_INT_CTL_TC BIT(12)
+
+#define SUN6I_INT_STA_REG 0x14
+
+#define SUN6I_FIFO_CTL_REG 0x18
+#define SUN6I_FIFO_CTL_RF_RST BIT(15)
+#define SUN6I_FIFO_CTL_TF_RST BIT(31)
+
+#define SUN6I_FIFO_STA_REG 0x1c
+#define SUN6I_FIFO_STA_RF_CNT_MASK 0x7f
+#define SUN6I_FIFO_STA_RF_CNT_BITS 0
+#define SUN6I_FIFO_STA_TF_CNT_MASK 0x7f
+#define SUN6I_FIFO_STA_TF_CNT_BITS 16
+
+#define SUN6I_CLK_CTL_REG 0x24
+#define SUN6I_CLK_CTL_CDR2_MASK 0xff
+#define SUN6I_CLK_CTL_CDR2(div) (((div) & SUN6I_CLK_CTL_CDR2_MASK) << 0)
+#define SUN6I_CLK_CTL_CDR1_MASK 0xf
+#define SUN6I_CLK_CTL_CDR1(div) (((div) & SUN6I_CLK_CTL_CDR1_MASK) << 8)
+#define SUN6I_CLK_CTL_DRS BIT(12)
+
+#define SUN6I_BURST_CNT_REG 0x30
+#define SUN6I_BURST_CNT(cnt) ((cnt) & 0xffffff)
+
+#define SUN6I_XMIT_CNT_REG 0x34
+#define SUN6I_XMIT_CNT(cnt) ((cnt) & 0xffffff)
+
+#define SUN6I_BURST_CTL_CNT_REG 0x38
+#define SUN6I_BURST_CTL_CNT_STC(cnt) ((cnt) & 0xffffff)
+
+#define SUN6I_TXDATA_REG 0x200
+#define SUN6I_RXDATA_REG 0x300
+
+struct sun6i_spi {
+ struct spi_master *master;
+ void __iomem *base_addr;
+ struct clk *hclk;
+ struct clk *mclk;
+ struct reset_control *rstc;
+
+ struct completion done;
+
+ const u8 *tx_buf;
+ u8 *rx_buf;
+ int len;
+};
+
+static inline u32 sun6i_spi_read(struct sun6i_spi *sspi, u32 reg)
+{
+ return readl(sspi->base_addr + reg);
+}
+
+static inline void sun6i_spi_write(struct sun6i_spi *sspi, u32 reg, u32 value)
+{
+ writel(value, sspi->base_addr + reg);
+}
+
+static inline void sun6i_spi_drain_fifo(struct sun6i_spi *sspi, int len)
+{
+ u32 reg, cnt;
+ u8 byte;
+
+ /* See how much data are available */
+ reg = sun6i_spi_read(sspi, SUN6I_FIFO_STA_REG);
+ reg &= SUN6I_FIFO_STA_RF_CNT_MASK;
+ cnt = reg >> SUN6I_FIFO_STA_RF_CNT_BITS;
+
+ if (len > cnt)
+ len = cnt;
+
+ while (len--) {
+ byte = readb(sspi->base_addr + SUN6I_RXDATA_REG);
+ if (sspi->rx_buf)
+ *sspi->rx_buf++ = byte;
+ }
+}
+
+static inline void sun6i_spi_fill_fifo(struct sun6i_spi *sspi, int len)
+{
+ u8 byte;
+
+ if (len > sspi->len)
+ len = sspi->len;
+
+ while (len--) {
+ byte = sspi->tx_buf ? *sspi->tx_buf++ : 0;
+ writeb(byte, sspi->base_addr + SUN6I_TXDATA_REG);
+ sspi->len--;
+ }
+}
+
+static int sun6i_spi_start_transfer(struct spi_device *spi,
+ struct spi_transfer *tfr)
+{
+ struct sun6i_spi *sspi = spi_master_get_devdata(spi->master);
+ unsigned int bursts = 0, tx_len = 0;
+ unsigned int mclk_rate, div;
+ u32 reg;
+
+ reinit_completion(&sspi->done);
+ sspi->tx_buf = tfr->tx_buf;
+ sspi->rx_buf = tfr->rx_buf;
+ sspi->len = tfr->len;
+
+ /* Clear pending interrupts */
+ sun6i_spi_write(sspi, SUN6I_INT_STA_REG, ~0);
+
+ /* Reset FIFO */
+ sun6i_spi_write(sspi, SUN6I_FIFO_CTL_REG,
+ SUN6I_FIFO_CTL_RF_RST | SUN6I_FIFO_CTL_TF_RST);
+
+ /*
+ * Setup the transfer control register: Chip Select,
+ * polarities, etc.
+ */
+ reg = SUN6I_TFR_CTL_CS(spi->chip_select);
+
+ if (spi->mode & SPI_CPOL)
+ reg |= SUN6I_TFR_CTL_CPOL;
+
+ if (spi->mode & SPI_CPHA)
+ reg |= SUN6I_TFR_CTL_CPHA;
+
+ if (!(spi->mode & SPI_CS_HIGH))
+ reg |= SUN6I_TFR_CTL_SPOL;
+
+ if (spi->mode & SPI_LSB_FIRST)
+ reg |= SUN6I_TFR_CTL_FBS;
+
+ sun6i_spi_write(sspi, SUN6I_TFR_CTL_REG, reg);
+
+ /*
+ * Setup clock divider.
+ *
+ * We have two choices there. Either we can use the clock
+ * divide rate 1, which is calculated thanks to this formula:
+ * SPI_CLK = MOD_CLK / (2 ^ cdr)
+ * Or we can use CDR2, which is calculated with the formula:
+ * SPI_CLK = MOD_CLK / (2 * (cdr + 1))
+ * Wether we use the former or the latter is set through the
+ * DRS bit.
+ *
+ * First try CDR2, and if we can't reach the expected
+ * frequency, fall back to CDR1.
+ */
+ mclk_rate = clk_get_rate(sspi->mclk);
+ div = mclk_rate / (spi->max_speed_hz << 1);
+
+ if (div <= (SUN6I_CLK_CTL_CDR2_MASK + 1)) {
+ if (div > 0)
+ div--;
+
+ reg = SUN6I_CLK_CTL_CDR2(div) | SUN6I_CLK_CTL_DRS;
+ } else {
+ div = ilog2(mclk_rate) - ilog2(spi->max_speed_hz);
+ reg = SUN6I_CLK_CTL_CDR1(div);
+ }
+
+ sun6i_spi_write(sspi, SUN6I_CLK_CTL_REG, reg);
+
+ /* Setup the transfer now... */
+ if (sspi->rx_buf && sspi->tx_buf) {
+ bursts = tfr->len + 1;
+ tx_len = tfr->len;
+ } else if (sspi->tx_buf) {
+ bursts = tfr->len;
+ tx_len = tfr->len;
+ } else if (sspi->rx_buf) {
+ bursts = tfr->len;
+ }
+
+ /* Setup the counters */
+ sun6i_spi_write(sspi, SUN6I_BURST_CNT_REG, SUN6I_BURST_CNT(bursts));
+ sun6i_spi_write(sspi, SUN6I_XMIT_CNT_REG, SUN6I_XMIT_CNT(tx_len));
+ sun6i_spi_write(sspi, SUN6I_BURST_CTL_CNT_REG,
+ SUN6I_BURST_CTL_CNT_STC(tx_len));
+
+ /* Fill the TX FIFO */
+ sun6i_spi_fill_fifo(sspi, SUN6I_FIFO_DEPTH);
+
+ /* Enable the interrupts */
+ sun6i_spi_write(sspi, SUN6I_INT_CTL_REG,
+ SUN6I_INT_CTL_TC | SUN6I_INT_CTL_RF_OVF);
+
+ /* Start the transfer */
+ reg = sun6i_spi_read(sspi, SUN6I_TFR_CTL_REG);
+ sun6i_spi_write(sspi, SUN6I_TFR_CTL_REG, reg | SUN6I_TFR_CTL_XCH);
+
+ return 0;
+}
+
+static int sun6i_spi_finish_transfer(struct spi_device *spi,
+ struct spi_transfer *tfr,
+ bool cs_change)
+{
+ struct sun6i_spi *sspi = spi_master_get_devdata(spi->master);
+
+ sun6i_spi_drain_fifo(sspi, SUN6I_FIFO_DEPTH);
+
+ if (tfr->delay_usecs)
+ udelay(tfr->delay_usecs);
+
+ return 0;
+}
+
+static int sun6i_spi_transfer_one(struct spi_master *master,
+ struct spi_message *mesg)
+{
+ struct sun6i_spi *sspi = spi_master_get_devdata(master);
+ struct spi_device *spi = mesg->spi;
+ struct spi_transfer *tfr;
+ unsigned int timeout;
+ int cs_change, err;
+ u32 reg;
+
+ list_for_each_entry(tfr, &mesg->transfers, transfer_list) {
+ err = sun6i_spi_start_transfer(spi, tfr);
+ if (err)
+ goto out;
+
+ timeout = wait_for_completion_timeout(&sspi->done,
+ msecs_to_jiffies(1000));
+ if (!timeout) {
+ err = -ETIMEDOUT;
+ goto out;
+ }
+
+ cs_change = tfr->cs_change ||
+ list_is_last(&tfr->transfer_list, &mesg->transfers);
+
+ err = sun6i_spi_finish_transfer(spi, tfr, cs_change);
+ if (err)
+ goto out;
+
+ mesg->actual_length += tfr->len;
+ }
+
+out:
+ reg = sun6i_spi_read(sspi, SUN6I_INT_CTL_REG);
+ sun6i_spi_write(sspi, SUN6I_INT_CTL_REG, reg & ~SUN6I_INT_CTL_TC);
+
+ mesg->status = err;
+ spi_finalize_current_message(master);
+ return 0;
+}
+
+/* wake up the sleep thread, and give the result code */
+static irqreturn_t sun6i_spi_handler(int irq, void *dev_id)
+{
+ struct sun6i_spi *sspi = dev_id;
+ u32 status = sun6i_spi_read(sspi, SUN6I_INT_STA_REG);
+
+ /* Transfer complete */
+ if (status & SUN6I_INT_CTL_TC) {
+ sun6i_spi_write(sspi, SUN6I_INT_STA_REG, SUN6I_INT_CTL_TC);
+ complete(&sspi->done);
+ return IRQ_HANDLED;
+ }
+
+ if (status & SUN6I_INT_CTL_RF_OVF) {
+ sun6i_spi_drain_fifo(sspi, SUN6I_FIFO_DEPTH);
+ sun6i_spi_write(sspi, SUN6I_INT_STA_REG, SUN6I_INT_CTL_RF_OVF);
+ return IRQ_HANDLED;
+ }
+
+ return IRQ_NONE;
+}
+
+static int sun6i_spi_probe(struct platform_device *pdev)
+{
+ struct spi_master *master;
+ struct sun6i_spi *sspi;
+ struct resource *res;
+ int ret = 0, irq;
+
+ master = spi_alloc_master(&pdev->dev, sizeof(struct sun6i_spi));
+ if (!master) {
+ dev_err(&pdev->dev, "Unable to allocate SPI Master\n");
+ return -ENOMEM;
+ }
+
+ platform_set_drvdata(pdev, master);
+ sspi = spi_master_get_devdata(master);
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ sspi->base_addr = devm_request_and_ioremap(&pdev->dev, res);
+ if (!sspi->base_addr) {
+ dev_err(&pdev->dev, "Unable to remap IO\n");
+ ret = -ENXIO;
+ goto err;
+ }
+
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0) {
+ dev_err(&pdev->dev, "No spi IRQ specified\n");
+ ret = -ENXIO;
+ goto err;
+ }
+
+ ret = devm_request_irq(&pdev->dev, irq, sun6i_spi_handler,
+ 0, "sun6i-spi", sspi);
+ if (ret) {
+ dev_err(&pdev->dev, "Cannot request IRQ\n");
+ goto err;
+ }
+
+ sspi->master = master;
+ master->bus_num = -1;
+ master->transfer_one_message = sun6i_spi_transfer_one;
+ master->num_chipselect = 4;
+ master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH | SPI_LSB_FIRST;
+ master->dev.of_node = pdev->dev.of_node;
+
+ /* Setup clocks */
+ sspi->hclk = devm_clk_get(&pdev->dev, "ahb");
+ if (IS_ERR(sspi->hclk)) {
+ dev_err(&pdev->dev, "Unable to acquire AHB clock\n");
+ ret = PTR_ERR(sspi->hclk);
+ goto err;
+ }
+
+ ret = clk_prepare_enable(sspi->hclk);
+ if (ret) {
+ dev_err(&pdev->dev, "Couldn't enable clock 'ahb spi'\n");
+ goto err;
+ }
+
+ sspi->mclk = devm_clk_get(&pdev->dev, "mod");
+ if (IS_ERR(sspi->mclk)) {
+ dev_err(&pdev->dev, "Unable to acquire module clock\n");
+ ret = PTR_ERR(sspi->mclk);
+ goto err2;
+ }
+
+ ret = clk_set_rate(sspi->mclk, 100000000);
+ if (ret) {
+ dev_err(&pdev->dev, "Couldn't change module clock rate\n");
+ goto err2;
+ }
+
+ ret = clk_prepare_enable(sspi->mclk);
+ if (ret) {
+ dev_err(&pdev->dev, "Couldn't enable clock 'ahb spi'\n");
+ goto err2;
+ }
+
+ init_completion(&sspi->done);
+
+ sspi->rstc = devm_reset_control_get(&pdev->dev, NULL);
+ if (IS_ERR(sspi->rstc)) {
+ dev_err(&pdev->dev, "Couldn't get reset controller\n");
+ ret = PTR_ERR(sspi->rstc);
+ goto err3;
+ }
+
+ ret = reset_control_deassert(sspi->rstc);
+ if (ret) {
+ dev_err(&pdev->dev, "Couldn't deassert the device from reset\n");
+ goto err3;
+ }
+
+ sun6i_spi_write(sspi, SUN6I_GBL_CTL_REG,
+ SUN6I_GBL_CTL_BUS_ENABLE | SUN6I_GBL_CTL_MASTER | SUN6I_GBL_CTL_TP);
+
+ ret = spi_register_master(master);
+ if (ret) {
+ dev_err(&pdev->dev, "cannot register SPI master\n");
+ goto err4;
+ }
+
+ return 0;
+
+err4:
+ reset_control_assert(sspi->rstc);
+err3:
+ clk_disable_unprepare(sspi->mclk);
+err2:
+ clk_disable_unprepare(sspi->hclk);
+err:
+ spi_master_put(master);
+
+ return ret;
+}
+
+static int sun6i_spi_remove(struct platform_device *pdev)
+{
+ struct spi_master *master = spi_master_get(platform_get_drvdata(pdev));
+ struct sun6i_spi *sspi = spi_master_get_devdata(master);
+
+ spi_unregister_master(master);
+ reset_control_assert(sspi->rstc);
+ clk_disable_unprepare(sspi->mclk);
+ clk_disable_unprepare(sspi->hclk);
+ spi_master_put(master);
+
+ return 0;
+}
+
+static const struct of_device_id sun6i_spi_match[] = {
+ { .compatible = "allwinner,sun6i-a31-spi", },
+ {}
+};
+MODULE_DEVICE_TABLE(of, sun6i_spi_match);
+
+static struct platform_driver sun6i_spi_driver = {
+ .probe = sun6i_spi_probe,
+ .remove = sun6i_spi_remove,
+ .driver = {
+ .name = "sun6i-spi",
+ .owner = THIS_MODULE,
+ .of_match_table = sun6i_spi_match,
+ },
+};
+module_platform_driver(sun6i_spi_driver);
+
+MODULE_AUTHOR("Pan Nan <pannan@xxxxxxxxxxxxxxxxx>");
+MODULE_AUTHOR("Maxime Ripard <maxime.ripard@xxxxxxxxxxxxxxxxxx>");
+MODULE_DESCRIPTION("Allwinner A31 SPI controller driver");
+MODULE_LICENSE("GPL");
--
1.8.4.2
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/