Re: [PATCH V5 4/8] phy: st-miphy-40lp: Add skeleton driver

[Arnd Bergmann]

On Monday 10 February 2014, Mohit Kumar wrote:
> diff --git a/Documentation/devicetree/bindings/phy/st-miphy40lp.txt b/Documentation/devicetree/bindings/phy/st-miphy40lp.txt
> new file mode 100644
> index 0000000..d0c7096
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/phy/st-miphy40lp.txt
> @@ -0,0 +1,12 @@
> +Required properties:
> +- compatible : should be "st,miphy40lp-phy"
> +	Other supported soc specific compatible:
> +		"st,spear1310-miphy"
> +		"st,spear1340-miphy"
> +- reg : offset and length of the PHY register set.
> +- misc: phandle for the syscon node to access misc registers
> +- phy-id: Instance id of the phy.
> +- #phy-cells : from the generic PHY bindings, must be 1.
> +	- 1st cell: phandle to the phy node.
> +	- 2nd cell: 0 if phy (in 1st cell) is to be used for SATA, 1 for PCIe
> +	  and 2 for Super Speed USB.

It's common to start this file with a small header explaining what this
hardware is.

> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
> index afa2354..2f58993 100644
> --- a/drivers/phy/Kconfig
> +++ b/drivers/phy/Kconfig
> @@ -64,4 +64,10 @@ config BCM_KONA_USB2_PHY
>  	help
>  	  Enable this to support the Broadcom Kona USB 2.0 PHY.
>  
> +config PHY_ST_MIPHY40LP
> +	tristate "ST MIPHY 40LP driver"
> +	help
> +	  Support for ST MIPHY 40LP which can be used for PCIe, SATA and Super Speed USB.
> +	select GENERIC_PHY
> +
>  endmenu

The 'select' statement should come before 'help', for consistency with the
rest of the kernel. Maybe mention that this phy is used inside the
spear13xx SoC here rather than a standalone phy.

> +	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
> +	if (!priv) {
> +		dev_err(dev, "can't alloc miphy40lp private date memory\n");
> +		return -ENOMEM;
> +	}
> +
> +	priv->plat_ops = (struct miphy40lp_plat_ops *)of_id->data;

The cast would incorrectly remove the 'const' attribute of the pointer.
Better remove the cast and make priv->plat_ops const.

> +static int __init miphy40lp_phy_init(void)
> +{
> +
> +	return platform_driver_probe(&miphy40lp_driver,
> +				miphy40lp_probe);
> +}
> +module_init(miphy40lp_phy_init);

There should certainly be a module_exit() function here so you can unload the
driver.

	Arnd
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/