Re: 3.12: ethernet controller missing after resuming from suspend to RAM

[Rafael J. Wysocki]

On Tuesday, February 11, 2014 07:17:37 PM Peter Wu wrote:
> On Tuesday 11 February 2014 12:42:37 Mika Westerberg wrote:
> > On Mon, Feb 10, 2014 at 11:39:29PM +0100, Rafael J. Wysocki wrote:
> > > > _STA() returns 0x0A instead of 0x0F. Could there be something missing in
> > > > the ACPI hotplug code that overlooks this and removes the device on
> > > > resume?
> > > 
> > > That is possible.  Actually even quite likely, but let's wait for the
> > > response from Peter.
> > 
> > Here's a hack that should take the 0xa return value into consideration. It
> > turned out that this case is even mentioned in the ACPI spec.
> 
> Tested-by: Peter Wu <lekensteyn@xxxxxxxxx>
> 
> This works, the devices are not lost anymore after resume. dmesg
> mentions the 04:00.* devices at resume compared to the unpatched kernel:
> 
> [   42.650721] PM: Finishing wakeup.
> [   42.650768] acpiphp_glue: hotplug_event: Bus check notify on \_SB_.PCI0.RP03
> [   42.650772] acpiphp_glue: hotplug_event: re-enumerating slots under \_SB_.PCI0.RP03
> [   42.650874] iwlwifi 0000:05:00.0: no hotplug settings from platform
> [   42.650722] Restarting tasks ... done.
> [   42.650985] video LNXVIDEO:00: Restoring backlight state
> [   42.650988] video LNXVIDEO:01: Restoring backlight state
> [   43.124208] ACPI: \_SB_.AC__: ACPI_NOTIFY_BUS_CHECK event: unsupported
> [   43.128401] jme 0000:04:00.5: irq 50 for MSI/MSI-X
> [   43.153005] jme 0000:04:00.5 eth0: Link is down
> [   43.153030] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
> [   43.154364] iwlwifi 0000:05:00.0: L1 Enabled; Disabling L0S
> [   43.162307] iwlwifi 0000:05:00.0: Radio type=0x1-0x3-0x1
> [   43.276220] acpiphp_glue: hotplug_event: Bus check notify on \_SB_.PCI0.RP01
> [   43.276223] acpiphp_glue: hotplug_event: re-enumerating slots under \_SB_.PCI0.RP01
> [   43.276257] xhci_hcd 0000:02:00.0: no hotplug settings from platform
> [   43.276267] acpiphp_glue: hotplug_event: Bus check notify on \_SB_.PCI0.RP02
> [   43.276268] acpiphp_glue: hotplug_event: re-enumerating slots under \_SB_.PCI0.RP02
> [   43.276355] sdhci-pci 0000:04:00.0: no hotplug settings from platform
> [   43.276368] pci 0000:04:00.2: no hotplug settings from platform
> [   43.276381] jmb38x_ms 0000:04:00.3: no hotplug settings from platform
> [   43.276393] jme 0000:04:00.5: no hotplug settings from platform
> [   43.276398] acpiphp_glue: hotplug_event: Bus check notify on \_SB_.PCI0.RP03
> [   43.276399] acpiphp_glue: hotplug_event: re-enumerating slots under \_SB_.PCI0.RP03
> [   43.276491] iwlwifi 0000:05:00.0: no hotplug settings from platform
> [   43.277214] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
> 
> Rafael, do you want me to test the other patch as well?

No, thanks!

Mika, I'll add a changelog to your patch and queue it up as a fix for 3.14.

Thanks!


> > diff --git a/drivers/pci/hotplug/acpiphp_glue.c
> > b/drivers/pci/hotplug/acpiphp_glue.c index e2a783fdb98f..014381b42d86
> > 100644
> > --- a/drivers/pci/hotplug/acpiphp_glue.c
> > +++ b/drivers/pci/hotplug/acpiphp_glue.c
> > @@ -730,6 +730,17 @@ static unsigned int get_slot_status(struct acpiphp_slot
> > *slot) return (unsigned int)sta;
> >  }
> > 
> > +static inline bool device_sta_valid(unsigned long long sta)
> > +{
> > +	/*
> > +	 * ACPI spec says that _STA may return bit 0 clear with bit 8 set
> > +	 * if the device is valid but does not require device driver to be
> > +	 * loaded (chapter 6.3.7).
> > +	 */
> > +	unsigned mask = ACPI_STA_DEVICE_ENABLED | ACPI_STA_DEVICE_FUNCTIONING;
> > +	return (sta & mask) == mask;
> > +}
> > +
> >  /**
> >   * trim_stale_devices - remove PCI devices that are not responding.
> >   * @dev: PCI device to start walking the hierarchy from.
> > @@ -745,7 +756,7 @@ static void trim_stale_devices(struct pci_dev *dev)
> >  		unsigned long long sta;
> > 
> >  		status = acpi_evaluate_integer(handle, "_STA", NULL, &sta);
> > -		alive = (ACPI_SUCCESS(status) && sta == ACPI_STA_ALL)
> > +		alive = (ACPI_SUCCESS(status) && device_sta_valid(sta))
> > 
> >  			|| acpiphp_no_hotplug(handle);
> > 
> >  	}
> >  	if (!alive) {
> > @@ -792,7 +803,7 @@ static void acpiphp_check_bridge(struct acpiphp_bridge
> > *bridge) mutex_lock(&slot->crit_sect);
> >  		if (slot_no_hotplug(slot)) {
> >  			; /* do nothing */
> > -		} else if (get_slot_status(slot) == ACPI_STA_ALL) {
> > +		} else if (device_sta_valid(get_slot_status(slot))) {
> >  			/* remove stale devices if any */
> >  			list_for_each_entry_safe_reverse(dev, tmp,
> >  							 &bus->devices, bus_list)
> 

-- 
I speak only for myself.
Rafael J. Wysocki, Intel Open Source Technology Center.
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/