Re: [PATCH 3/3] ARM: at91: dt: sam9rl: Device Tree for the at91sam9rlek

[Alexandre Belloni]

On 17/02/2014 at 11:30:57 +0100, Nicolas Ferre wrote :
> On 15/02/2014 02:14, Alexandre Belloni :
> > Add a device tree for the at91sam9rl-ek. For now it supports:
> >  - MMC
> >  - dbgu
> >  - usart1
> >  - watchdog
> >  - nand
> >  - leds
> >  - buttons
> > 
> > Signed-off-by: Alexandre Belloni <alexandre.belloni@xxxxxxxxxxxxxxxxxx>
> > ---
> >  arch/arm/boot/dts/Makefile         |   2 +
> >  arch/arm/boot/dts/at91sam9rlek.dts | 151 +++++++++++++++++++++++++++++++++++++
> >  2 files changed, 153 insertions(+)
> >  create mode 100644 arch/arm/boot/dts/at91sam9rlek.dts
> > 
> > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> > index d57c1a65b24f..bb28e65d17ee 100644
> > --- a/arch/arm/boot/dts/Makefile
> > +++ b/arch/arm/boot/dts/Makefile
> > @@ -28,6 +28,8 @@ dtb-$(CONFIG_ARCH_AT91) += at91sam9m10g45ek.dtb
> >  dtb-$(CONFIG_ARCH_AT91) += pm9g45.dtb
> >  # sam9n12
> >  dtb-$(CONFIG_ARCH_AT91) += at91sam9n12ek.dtb
> > +# sam9rl
> > +dtb-$(CONFIG_ARCH_AT91) += at91sam9rlek.dtb
> >  # sam9x5
> >  dtb-$(CONFIG_ARCH_AT91) += at91-ariag25.dtb
> >  dtb-$(CONFIG_ARCH_AT91) += at91sam9g15ek.dtb
> > diff --git a/arch/arm/boot/dts/at91sam9rlek.dts b/arch/arm/boot/dts/at91sam9rlek.dts
> > new file mode 100644
> > index 000000000000..5ec9589613a1
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/at91sam9rlek.dts
> > @@ -0,0 +1,151 @@
> > +/*
> > + * at91sam9rlek.dts - Device Tree file for Atmel at91sam9rl reference board
> > + *
> > + *  Copyright (C) 2014  Alexandre Belloni <alexandre.belloni@xxxxxxxxxxxxxxxxxx>
> > + *
> > + * Licensed under GPLv2 only
> > + */
> > +/dts-v1/;
> > +#include "at91sam9rl.dtsi"
> > +
> > +/ {
> > +	model = "Atmel at91sam9rlek";
> > +	compatible = "atmel,at91sam9rlek", "atmel,at91sam9rl", "atmel,at91sam9";
> > +
> > +	chosen {
> > +		bootargs = "console=ttyS0,115200 rootfstype=ubifs root=ubi0:rootfs ubi.mtd=7 rw";
> 
> Isn't it ubi.mtd=5 according to the NAND layer below?
> 

Sure, I forgot to change it after updating the nand layout.

> > +	};
> > +
> > +	memory {
> > +		reg = <0x20000000 0x4000000>;
> > +	};
> > +
> > +	clocks {
> > +		#address-cells = <1>;
> > +		#size-cells = <1>;
> > +		ranges;
> > +
> > +		main_clock: clock@0 {
> > +			compatible = "atmel,osc", "fixed-clock";
> > +			clock-frequency = <12000000>;
> > +		};
> > +	};
> > +
> > +	ahb {
> > +		apb {
> > +			mmc0: mmc@fffa4000 {
> 
> Use address ascending order, even for the board, please.
> 

Sure.

> > +				pinctrl-0 = <
> > +					&pinctrl_board_mmc0
> > +					&pinctrl_mmc0_clk
> > +					&pinctrl_mmc0_slot0_cmd_dat0
> > +					&pinctrl_mmc0_slot0_dat1_3>;
> > +				status = "okay";
> > +				slot@0 {
> > +					reg = <0>;
> > +					bus-width = <4>;
> > +					cd-gpios = <&pioA 15 GPIO_ACTIVE_HIGH>;
> > +				};
> > +			};
> > +
> > +			dbgu: serial@fffff200 {
> > +				status = "okay";
> > +			};
> > +
> > +			usart0: serial@fffb0000 {
> > +				pinctrl-0 = <
> > +					&pinctrl_usart0
> > +					&pinctrl_usart0_rts
> > +					&pinctrl_usart0_cts>;
> > +				status = "okay";
> > +			};
> > +
> > +			pinctrl@fffff400 {
> > +				mmc0 {
> > +					pinctrl_board_mmc0: mmc0-board {
> > +						atmel,pins =
> > +							<AT91_PIOA 15 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
> > +					};
> > +				};
> > +			};
> > +
> > +			watchdog@fffffd40 {
> > +				status = "okay";
> > +			};
> > +		};
> > +
> > +		nand0: nand@40000000 {
> > +			nand-bus-width = <8>;
> > +			nand-ecc-mode = "soft";
> > +			nand-on-flash-bbt = <1>;
> > +			status = "okay";
> > +
> > +			at91bootstrap@0 {
> > +				label = "at91bootstrap";
> > +				reg = <0x0 0x40000>;
> > +			};
> > +
> > +			bootloader@40000 {
> > +				label = "bootloader";
> > +				reg = <0x40000 0x80000>;
> > +			};
> > +
> > +			bootloaderenv@c0000 {
> > +				label = "bootloader env";
> > +				reg = <0xc0000 0xc0000>;
> > +			};
> > +
> > +			dtb@180000 {
> > +				label = "device tree";
> > +				reg = <0x180000 0x80000>;
> > +			};
> > +
> > +			kernel@200000 {
> > +				label = "kernel";
> > +				reg = <0x200000 0x600000>;
> > +			};
> > +
> > +			rootfs@800000 {
> > +				label = "rootfs";
> > +				reg = <0x800000 0x0f800000>;
> > +			};
> > +		};
> > +	};
> > +
> > +	leds {
> > +		compatible = "gpio-leds";
> > +
> > +		ds1 {
> > +			label = "ds1";
> > +			gpios = <&pioD 15 GPIO_ACTIVE_LOW>;
> > +		};
> > +
> > +		ds2 {
> > +			label = "ds2";
> > +			gpios = <&pioD 16 GPIO_ACTIVE_LOW>;
> > +		};
> > +
> > +		ds3 {
> > +			label = "ds3";
> > +			gpios = <&pioD 14 GPIO_ACTIVE_HIGH>;
> > +			linux,default-trigger = "heartbeat";
> > +		};
> > +	};
> > +
> > +	gpio_keys {
> > +		compatible = "gpio-keys";
> > +
> > +		right_click {
> > +			label = "right_click";
> > +			gpios = <&pioB 0 GPIO_ACTIVE_LOW>;
> > +			linux,code = <273>;
> > +			gpio-key,wakeup;
> > +		};
> > +
> > +		left_click {
> > +			label = "left_click";
> > +			gpios = <&pioB 1 GPIO_ACTIVE_LOW>;
> > +			linux,code = <272>;
> > +			gpio-key,wakeup;
> > +		};
> > +	};
> > +};
> > 
> 
> Otherwise, seems okay:
> 
> when corrected, you can add my:
> 
> Acked-by: Nicolas Ferre <nicolas.ferre@xxxxxxxxx>
> 

Will do.


-- 
Alexandre Belloni, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/