[PATCH 20/35] mtd: st_spi_fsm: Update the flash Volatile Configuration Register

From: Lee Jones
Date: Tue Feb 18 2014 - 10:01:59 EST


The FSM Serial Flash Controller is driven by issuing a standard set of
register writes we call a message sequence. This patch supplies a method
to prepare the message sequence responsible for updating a chip's VCR.

Acked-by Angus Clark <angus.clark@xxxxxx>
Signed-off-by: Lee Jones <lee.jones@xxxxxxxxxx>
---
drivers/mtd/devices/st_spi_fsm.c | 32 ++++++++++++++++++++++++++++++++
1 file changed, 32 insertions(+)

diff --git a/drivers/mtd/devices/st_spi_fsm.c b/drivers/mtd/devices/st_spi_fsm.c
index e20f4cb..208b6c3 100644
--- a/drivers/mtd/devices/st_spi_fsm.c
+++ b/drivers/mtd/devices/st_spi_fsm.c
@@ -415,6 +415,23 @@ static struct stfsm_seq stfsm_seq_erase_sector = {
SEQ_CFG_STARTSEQ),
};

+static struct stfsm_seq stfsm_seq_wrvcr = {
+ .seq_opc[0] = (SEQ_OPC_PADS_1 | SEQ_OPC_CYCLES(8) |
+ SEQ_OPC_OPCODE(FLASH_CMD_WREN) | SEQ_OPC_CSDEASSERT),
+ .seq_opc[1] = (SEQ_OPC_PADS_1 | SEQ_OPC_CYCLES(8) |
+ SEQ_OPC_OPCODE(FLASH_CMD_WRVCR)),
+ .seq = {
+ STFSM_INST_CMD1,
+ STFSM_INST_CMD2,
+ STFSM_INST_STA_WR1,
+ STFSM_INST_STOP,
+ },
+ .seq_cfg = (SEQ_CFG_PADS_1 |
+ SEQ_CFG_READNOTWRITE |
+ SEQ_CFG_CSDEASSERT |
+ SEQ_CFG_STARTSEQ),
+};
+
static int stfsm_n25q_en_32bit_addr_seq(struct stfsm_seq *seq)
{
seq->seq_opc[0] = (SEQ_OPC_PADS_1 | SEQ_OPC_CYCLES(8) |
@@ -542,6 +559,21 @@ static int stfsm_enter_32bit_addr(struct stfsm *fsm, int enter)
return 0;
}

+static int stfsm_wrvcr(struct stfsm *fsm, uint8_t data)
+{
+ struct stfsm_seq *seq = &stfsm_seq_wrvcr;
+
+ dev_dbg(fsm->dev, "writing VCR 0x%02x\n", data);
+
+ seq->status = (STA_DATA_BYTE1(data) | STA_PADS_1 | STA_CSDEASSERT);
+
+ stfsm_load_seq(fsm, seq);
+
+ stfsm_wait_seq(fsm);
+
+ return 0;
+}
+
/*
* SoC reset on 'boot-from-spi' systems
*
--
1.8.3.2

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/