Re: [PATCH net V2] vhost: net: switch to use data copy if pending DMAs exceed the limit

From: Ronen Hod
Date: Mon Mar 17 2014 - 02:43:45 EST


On 03/13/2014 09:28 AM, Jason Wang wrote:
On 03/10/2014 04:03 PM, Michael S. Tsirkin wrote:
On Fri, Mar 07, 2014 at 01:28:27PM +0800, Jason Wang wrote:
We used to stop the handling of tx when the number of pending DMAs
exceeds VHOST_MAX_PEND. This is used to reduce the memory occupation
of both host and guest. But it was too aggressive in some cases, since
any delay or blocking of a single packet may delay or block the guest
transmission. Consider the following setup:

+-----+ +-----+
| VM1 | | VM2 |
+--+--+ +--+--+
| |
+--+--+ +--+--+
| tap0| | tap1|
+--+--+ +--+--+
| |
pfifo_fast htb(10Mbit/s)
| |
+--+--------------+---+
| bridge |
+--+------------------+
|
pfifo_fast
|
+-----+
| eth0|(100Mbit/s)
+-----+

- start two VMs and connect them to a bridge
- add an physical card (100Mbit/s) to that bridge
- setup htb on tap1 and limit its throughput to 10Mbit/s
- run two netperfs in the same time, one is from VM1 to VM2. Another is
from VM1 to an external host through eth0.
- result shows that not only the VM1 to VM2 traffic were throttled but
also the VM1 to external host through eth0 is also throttled somehow.

This is because the delay added by htb may lead the delay the finish
of DMAs and cause the pending DMAs for tap0 exceeds the limit
(VHOST_MAX_PEND). In this case vhost stop handling tx request until
htb send some packets. The problem here is all of the packets
transmission were blocked even if it does not go to VM2.

We can solve this issue by relaxing it a little bit: switching to use
data copy instead of stopping tx when the number of pending DMAs
exceed half of the vq size. This is safe because:

- The number of pending DMAs were still limited (half of the vq size)
- The out of order completion during mode switch can make sure that
most of the tx buffers were freed in time in guest.

So even if about 50% packets were delayed in zero-copy case, vhost
could continue to do the transmission through data copy in this case.

Test result:

Before this patch:
VM1 to VM2 throughput is 9.3Mbit/s
VM1 to External throughput is 40Mbit/s
CPU utilization is 7%

After this patch:
VM1 to VM2 throughput is 9.3Mbit/s
Vm1 to External throughput is 93Mbit/s
CPU utilization is 16%

Completed performance test on 40gbe shows no obvious changes in both
throughput and cpu utilization with this patch.

The patch only solve this issue when unlimited sndbuf. We still need a
solution for limited sndbuf.

Cc: Michael S. Tsirkin <mst@xxxxxxxxxx>
Cc: Qin Chuanyu <qinchuanyu@xxxxxxxxxx>
Signed-off-by: Jason Wang <jasowang@xxxxxxxxxx>
I thought hard about this.
Here's what worries me: if there are still head of line
blocking issues lurking in the stack, they will still
hurt guests such as windows which rely on timely
completion of buffers, but it makes it
that much harder to reproduce the problems with
linux guests which don't.
And this will make even it harder to figure out
whether zero copy is actually active to diagnose
high cpu utilization cases.
Yes.

So I think this is a good trick, but let's make
this path conditional on a new debugging module parameter:
how about head_of_line_blocking with default off?
Sure. But the head of line blocking was only partially solved in the
patch since we only support in-order completion of zerocopy packets.
Maybe we need consider switching to out of order completion even for
zerocopy skbs?

Yan, Dima,

I remember that there is an issue with out-of-order packets and WHQL.

Ronen.

This way if we suspect packets are delayed forever
somewhere, we can enable that and see guest networking block.

Additionally, I think we should add a way to count zero copy
and non zero copy packets.
I see two ways to implement this: add tracepoints in vhost-net
or add counters in tun accessible with ethtool.
This can be a patch on top and does not have to block
this one though.

Yes, I post a RFC about 2 years ago, see
https://lkml.org/lkml/2012/4/9/478 which only traces generic vhost
behaviours. I can refresh this and add some -net specific tracepoints.
--
To unsubscribe from this list: send the line "unsubscribe netdev" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/