Re: man termios

[Peter Hurley]

On 03/21/2014 09:15 AM, Michael Kerrisk (man-pages) wrote:
> On 03/21/2014 12:21 PM, Peter Hurley wrote:
> > On 03/21/2014 06:45 AM, Michael Kerrisk (man-pages) wrote:

> > > > Finally, if the 'count' parameter is less than MIN, read() may return before
> > > > MIN bytes have been received, if 'count' bytes have been received.
> > >
> > > Yes. But it's not clear to me here: do you mean that something in the
> > > man page (or in TLPI) needs fixing?
> >
> > Well, what I mean here is that read() may also _not_ return until MIN bytes have
> > been received, even if 'count' bytes have been received.
>
> Ahh -- I see what you mean. And, it looks like there is a point here where Linux
> differs from POSIX and (at least) Solaris. See the current man-page text below,
> in particular the MIN>0, TIME>0 case. I've also attached a simple test program
> that I used, below.
>
>         In noncanonical mode input is available immediately (without  the
>         user  having  to  type a line-delimiter character), no input proâ
>         cessing is performed, and line editing is disabled.  The settings
>         of  MIN (c_cc[VMIN]) and TIME (c_cc[VTIME]) determine the circumâ
>         stances in which a read(2) completes;  there  are  four  distinct
>         cases:
>
>         MIN == 0; TIME == 0:
>                If  data  is  available, read(2) returns immediately, with
>                the lesser of the number of bytes available, or the number
>                of  bytes  requested.   If  no  data is available, read(2)
>                returns 0.
>
>         MIN > 0; TIME == 0:
>                read(2) blocks until MIN bytes are available, and  returns
>                up to the number of bytes requested.
>
>         MIN == 0; TIME > 0:
>                TIME  specifies  the limit for a timer in tenths of a secâ
>                ond.   The  timer  is  started  when  read(2)  is  called.
>                read(2)  returns  either when at least one byte of data is
>                available, or  when  the  timer  expires.   If  the  timer
>                expires  without  any  input  becoming  available, read(2)
>                returns 0.  If data is already available at  the  time  of
>                the call to read() the call behaves as though the data was
>                received immediately after the call.
>
>         MIN > 0; TIME > 0:
>                TIME specifies the limit for a timer in tenths of  a  secâ
>                ond.  Once an initial byte of input becomes available, the
>                timer is restarted after each further  byte  is  received.
>                read(2)  returns  when  any of the following conditions is
>                met:
>
>                *  MIN bytes have been received.
>
>                *  The interbyte timer expires.
>
>                *  The number of  bytes  requested  by  read(2)  has  been
>                   received.   (POSIX  does  not  specify this termination
>                   condition, and on  some  other  implementations  read()
>                   does not return in this case.)
>
>                Because  the  timer is started only after the initial byte
>                becomes available, at least one byte  will  be  read.   If
>                data  is  already  available  at  the  time of the call to
>                read() the call behaves as though the  data  was  received
>                immediately after the call.
>
>         POSIX does not specify whether the setting of the O_NONBLOCK file
>         status flag takes precedence over the MIN and TIME settings.   If
>         O_NONBLOCK is set, a read() in noncanonical mode may return immeâ
>         diately, regardless of the setting of MIN or TIME.   Furthermore,
>         if  no  data is available, POSIX permits a read() in noncanonical
>         mode to return either 0, or -1 with errno set to EAGAIN.

All looks good.

Thanks again,
Peter Hurley

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/