Re: [PATCH v2 2/2] devicetree: Add devicetree bindings documentation for Cadence SPI

[Harini Katakam]

Hi Peter,

On Sun, Apr 6, 2014 at 5:13 AM, Peter Crosthwaite
<peter.crosthwaite@xxxxxxxxxx> wrote:
> On Sat, Apr 5, 2014 at 4:05 PM, Harini Katakam
> <harinikatakamlinux@xxxxxxxxx> wrote:
>> Hi Peter,
>>
>> On Sat, Apr 5, 2014 at 4:44 AM, Peter Crosthwaite
>> <peter.crosthwaite@xxxxxxxxxx> wrote:
>>> On Sat, Apr 5, 2014 at 12:30 AM, Harini Katakam
>>> <harinikatakamlinux@xxxxxxxxx> wrote:
>>>> Hi,
>>>>
>>>> On Fri, Apr 4, 2014 at 7:38 PM, Harini Katakam
>>>> <harinikatakamlinux@xxxxxxxxx> wrote:
>>>>> Hi Mark,
>>>>>
>>>>> On Fri, Apr 4, 2014 at 6:16 PM, Mark Brown <broonie@xxxxxxxxxx> wrote:
>>>>>> On Fri, Apr 04, 2014 at 05:44:23PM +0530, Harini Katakam wrote:
>>>>>>> On Fri, Apr 4, 2014 at 3:39 PM, Mark Brown <broonie@xxxxxxxxxx> wrote:
>>>>>>> > On Fri, Apr 04, 2014 at 08:30:38AM +0530, Harini Katakam wrote:
>>>>>>
>>>>>>> >> This IP can drive 4 slaves.
>>>>>>> >> The sCS line to be driven is selected in spi device structure and
>>>>>>> >> that is driven by the software.
>>>>>>
>>>>>>> > So why specify this in the binding at all?  If the device always has the
>>>>>>> > same number of chip selects it's redundant.
>>>>>>
>>>>>>> I'm sorry, I should have explained that better.
>>>>>>> The IP can support upto 4 chip selects.
>>>>>>> The num-cs value here is the number of chip selects actually used on the board.
>>>
>>> Shouldnt it be a property of the controller not the board? How for
>>> example do we differentiate between different implementations of
>>> cadence SPI controller that only supports up to two CS lines? My
>>> thinking is that this property should always be present and = 4 in the
>>> Zynq case as the controller always has 4 physical CS lines coming out
>>> (before any decoders, pin muxes or slaves etc.).
>>>
>>>>>>
>>>>>> Why does that need to be configured?  Surely the presence of slaves is
>>>>>> enough information.
>>>
>>> And presence of slaves / board info is inferable from subnodes.
>>>
>>>>>
>>>>> OK. I understand.
>>>>> Can you comment on the case where a decoder is used?
>>>>>
>>>>> There is support for adding a decoder where extended slaves can be selected
>>>>> through the IP's control register.
>>>>> (This is not currently implemented in the driver but will be in the future.)
>>>>>
>>>
>>> I think thats seperate information. is-decoded-cs property of something.
>>>
>>>>> How should the driver know whether it is 4 or 16 select lines for example?
>>>>> This has to be written to master->num_chipselect.
>>>>>
>>>
>>> If you only have one property (== 4) how do you tell the difference
>>> between 4 un-decoded CS lines vs 2 decoded CS lines?
>>>
>>
>> If an SoC implements 2 CS and sets "decoder" property,
>> then we'd configure the register with "select decode" bit and write
>> 0b0011 to the slave select field to select 4th slave.
>>
>> If decoder property is not set, then we'd write 0b1000 to select 4th slave.
>>
>
> What are your proposed dt bindings for these differing options - what
> is num-cs in each case?

I think it will be better to have num-cs equal to the max slaves allowed and
the property to indicate if decoder is present helps driver configure the
register accordingly. (master->num_chipselect is written with "num-cs" value)

For ex.,
1. 4 slaves without decoder
num-cs = <4>
is-decoded-cs = <false>

2. 4 slaves driven through 2 to 4 decoder:
num-cs = <4>
is-decoded-cs = <true>

The other option is have num-cs reflect number of CS before decoder
but the above option makes more sense as num-cs directly reflects
the max valid slaves.

>
>> But yes, if the SoC only implements 2 CS, doesn't use decoder but
>> if there is an erroneous input to set_cs for 4th slave, it would be a problem.
>>
>
> Sure, that's an error condition though that should be caught by SPI
> because master->num_chipselect would only be 2 right?
>

Yes.

Regards,
Harini

> Regards,
> Peter
>
>>>
>>> I think num-cs has validity as the number of CS lines implemented in
>>> the controller. For any given SoC, it's constant but could differ
>>> between SoCs.
>>>
>>
>> I dint consider that this property will be useful to SoC's implementing <4 CS;
>> master->num_chipselect (when set to this property's value)
>> will be used to check error conditions.
>>
>> Regards,
>> Harini
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/