Re: [PATCH v3 0/5] Add support for SW babble Control
From: George Cherian
Date: Wed May 14 2014 - 01:38:15 EST
On 5/14/2014 12:07 AM, Bin Liu wrote:
Hi,
On Tue, May 13, 2014 at 8:24 AM, George Cherian <george.cherian@xxxxxx> wrote:
Hi Daniel,
On 5/13/2014 6:44 PM, Daniel Mack wrote:
Hi George,
On 05/13/2014 02:57 PM, George Cherian wrote:
I never enabled the MUSB_BABBLE_SW_SESSION_CTRL in the MUSB_BABBLE_CTL
reg.
can you try with the following patch.
diff --git a/drivers/usb/musb/musb_dsps.c b/drivers/usb/musb/musb_dsps.c
index 1ae6681..1160cd1 100644
--- a/drivers/usb/musb/musb_dsps.c
+++ b/drivers/usb/musb/musb_dsps.c
@@ -477,8 +477,11 @@ static int dsps_musb_init(struct musb *musb)
* logic enabled.
*/
val = dsps_readb(musb->mregs, MUSB_BABBLE_CTL);
- if (val == MUSB_BABBLE_RCV_DISABLE)
+ if (val == MUSB_BABBLE_RCV_DISABLE) {
glue->sw_babble_enabled = true;
+ val |= MUSB_BABBLE_SW_SESSION_CTRL;
+ dsps_writeb(musb->mregs, MUSB_BABBLE_CTL, val);
+ }
ret = dsps_musb_dbg_init(musb, glue);
if (ret)
MUSB_BABBLE_STUCK_J still remains unset, so I get the same result as
without the patch: a full glue reset is conducted. Do I get you right
that you expect MUSB_BABBLE_STUCK_J to be set in babble conditions when
MUSB_BABBLE_SW_SESSION_CTRL is set?
Basically, there are 2 types of babble conditions.
1) Transient babble condition - which could be recovered from without an IP
reset .
2) Babble condition - which could be recovered from only by doing an IP
reset.
Looks like you are always hitting case 2 (Most times am also hitting the
same).
Case 1 is really hard to reproduce. I don't have a reliable method as of now
to
reproduce this case consistently.
[ 19.672373] CAUTION: musb: Babble Interrupt Occurred
[ 19.677776] musb_stage0_irq 789: unhandled DISCONNECT transition
(a_wait_bcon)
[ 19.685815] usb 1-1: USB disconnect, device number 3
[ 19.769720] musb-hdrc musb-hdrc.0.auto: babble: MUSB_BABBLE_CTL value
44
[ 19.776765] musb-hdrc musb-hdrc.0.auto: STUCK_J is reset
I don't quite follow, especially as I lack documentation of the IP core.
How do you test babble errors, is there any way to force them to happen
reliably?
There is no 100% reliable method to force it to happen. Following is
I have a way to force babble happen reliably - shorting DP or DM to
VBUS. I opened the far-end plug of the USB cable, so I can easily
short DP or DM to VBUS.
Good to know that you have a reliable way to test babble condition.
Can you please do a quick test on 3.15.0-rc4 with the series applied?
In case of any assistance please do let me know.
But the interesting thing is that with TI 3.2 kernel, shorting DP or
DM to VBUS causes MISC register to be 0x4, but the result is
completely opposite in TI 3.12.10 kernel, which cause MISC to be 0x64.
So in the 3.2 kernel, the babble handing resets the controller, but
the 3.12.10 does not.
Regards,
-Bin.
my setup ,
I have a HUB with 4 devices connected , which gives me a Babble interrupt
on both connects and disconnects ( Not always though).
Anyway, the full glue layer solves this rare condition quite well for
me. Is there any downside of this?
Daniel
--
-George
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
--
-George
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/