Re: [PATCH 06/17] pci: host: pcie-designware: Use *base-mask* for configuring the iATU

[Arnd Bergmann]

On Wednesday 14 May 2014 11:14:45 Kishon Vijay Abraham I wrote:
> hi Arnd,
> 
> On Tuesday 13 May 2014 07:04 PM, Arnd Bergmann wrote:
> > On Tuesday 13 May 2014 15:27:46 Arnd Bergmann wrote:
> >> On Tuesday 13 May 2014 18:56:23 Kishon Vijay Abraham I wrote:
> >>>> If you have a case where the outbound translation is a 256MB (i.e. 28bit)
> >>>> section of the CPU address space, that could be represented as
> >>>>
> >>>>       ranges = <0x82000000 0 0  0xb0000000  0 0x10000000>;
> >>>>
> >>>> or 
> >>>>
> >>>>       ranges = <0x82000000 0 0xb0000000  0xb0000000  0 0x10000000>;
> >>>>
> >>>> depending on whether you want the BARs to be programmed using a low
> >>>> address 0x0-0x0fffffff or an address matching the window
> >>>> 0xb0000000-0xbfffffff.
> >>>
> >>> The problem is, for configuring the window starting at 0xb0000000, the ATU
> >>> should be programmed 0x0000000 (the cpu address for it will be 0xb0000000 though).
> >>>
> >>
> >> Then use the first of the two?
> >>
> > 
> > To clarify: using <0x82000000 0 0  0xb0000000  0 0x10000000> will give you 
> > a mem_offset of 0xb0000000, which should work just fine for this case.
> > 
> > What I don't understand is why the ATU cares about whether the outbound
> > address is 0x0000000 or 0xb0000000 if it just decodes the lower 28 bit
> > anyway. Did you mean that we have to program the BARs using low addresses
> > regardless of what is programmed in the ATU? That would make more sense,
> > and it also matches what I suggested.
> 
> No, It's not like it decodes only the lower 28bits. The BARs is programmed with
> 32 bit value.
> 
> My pcie dt node has
>  ranges = <0x00000800 0 0x20001000 0x20001000 0 0x00002000  /* CONFIG */
>            0x81000000 0 0          0x20003000 0 0x00010000  /* IO */
>            0x82000000 0 0x20013000 0x20013000 0 0xffed000>; /* MEM */
> 
> Consider MEM address space..
> 
> Here both PCI address and CPU address is 0x20013000. So when there is a write
> to cpu addr 0x20013000 [writel(virt_addr(0x20013000)], we want it to be
> translated to PCI addr 0x20013000. So in 'ATU', we would expect *base* to be
> programmed to *0x20013000* and target to be programmed to *0x20013000*. But
> that's not the case for DRA7xx. For DRA7xx *base* should be programmed to
> *0x0013000* and target should be programmed to *0x20013000*.

Ok, got it, thanks for your patience.

I think this would best be modeled as a separate bus node that contains the
restriction, like this:

/ {
	#address-cells = <1>; // or <2> if you support > 4GB address space
	#size-cells = <1>;

	soc {
		#address-cells <1>;
		#size-cells = <1>;
		ranges;
		dma-ranges;

		... // all normal devices

		axi@20000000 {
			#size-cells = <1>;
			#address-cells = <1>;
			dma-ranges; // can access all 4GB outbound
			ranges = <0 0x20000000 0x10000000>; // 28-bit bus

			pci@0 {
				reg = <0x0    0x1000>, // internal regs
				      <0x1000 0x2000>; // config space
				dma-ranges; // 32-bit outbound
				ranges = <0x81000000 0 0           0x3000 0 0x00010000  /* IO */
					  0x82000000 0 0x20013000 0x13000 0 0xffed000>; /* MEM */
			};
		};
	};
};


	Arnd
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/