Re: [Fwd: Re: [PATCH 1/1] drivers/scsi/tmscsim.c: replace shift loop by ilog2]

[Guennadi Liakhovetski]

Hi

On Tue, 20 May 2014, Joe Perches wrote:

> Hello Kurt.
> 
> If you're still interested in tmscim.
> 
> Your garloff@xxxxxxx address bounces....
> 
> btw:  Your MAINTAINERS entry is out of date.
> 
> MAINTAINERS-DC390/AM53C974 SCSI driver
> MAINTAINERS:M:  Kurt Garloff <garloff@xxxxxxx>
> MAINTAINERS:W:  http://www.garloff.de/kurt/linux/dc390/
> MAINTAINERS-M:  Guennadi Liakhovetski <g.liakhovetski@xxxxxx>
> MAINTAINERS-S:  Maintained
> MAINTAINERS-F:  drivers/scsi/tmscsim.*
> 
> -------- Forwarded Message --------
> From: Joe Perches <joe@xxxxxxxxxxx>
> To: Fabian Frederick <fabf@xxxxxxxxx>
> Cc: linux-kernel <linux-kernel@xxxxxxxxxxxxxxx>, Kurt Garloff
> <garloff@xxxxxxx>, akpm <akpm@xxxxxxxxxxxxxxxxxxxx>
> Subject: Re: [PATCH 1/1] drivers/scsi/tmscsim.c: replace shift loop by
> ilog2
> 
> On Tue, 2014-05-20 at 18:48 +0200, Fabian Frederick wrote:
> > Cc: Kurt Garloff <garloff@xxxxxxx>
> > Cc: Andrew Morton <akpm@xxxxxxxxxxxxxxxxxxxx>
> > Signed-off-by: Fabian Frederick <fabf@xxxxxxxxx>
> > ---
> >  drivers/scsi/tmscsim.c | 2 +-
> >  1 file changed, 1 insertion(+), 1 deletion(-)
> > 
> > diff --git a/drivers/scsi/tmscsim.c b/drivers/scsi/tmscsim.c
> []
> > @@ -1611,7 +1611,7 @@ dc390_Reselect( struct dc390_acb* pACB )
> >        printk (KERN_ERR "DC390: Reselection must select host adapter: %02x!\n", lun);
> >      else
> >        lun ^= 1 << pACB->pScsiHost->this_id; /* Mask AdapterID */
> > -    id = 0; while (lun >>= 1) id++;
> > +    id = ilog2(lun);
> >      /* Get LUN */
> >      lun = DC390_read8 (ScsiFifo);
> >      if (!(lun & IDENTIFY_BASE)) printk (KERN_ERR "DC390: Resel: Expect identify message!\n");
> 
> Hey Fabian.
> 
> You've submitted several of these now.
> 
> Have you gone through all of these to make sure
> that the ilog2(<foo>) uses are always using a
> non-zero <foo>?

I think here at least, lun indeed can be 0, at least there's a test there:

    if (!(lun & (1 << pACB->pScsiHost->this_id)))
      printk (KERN_ERR "DC390: Reselection must select host adapter: %02x!\n", lun);

So, it is possible, that the "1 << this_id" bit is not set, then possibly 
it can be 0 too... Although from the hardware / SCSI PoV I'm not sure TBH. 
To be on the safe side we could at least add a check for 0 and only use 
ilog2, for != 0.

Thanks
Guennadi

> If so, that should be mentioned in the changelog.
> 
> These should probably add #include <linux/log2.h>
> 
> It would have been nicer to use a patch series
> and a cover letter so I could make this reply to
> to cover letter.
> 
> Please take the time to setup and use git send-email
> instead of sylpheed.
> 
> 
> 
> --
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@xxxxxxxxxxxxxxx
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at  http://www.tux.org/lkml/
> 

---
Guennadi Liakhovetski, Ph.D.
Freelance Open-Source Software Developer
http://www.open-technology.de/
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/