Re: [PATCH v2 00/14] Add Qualcomm SD Card Controller support

[Srinivas Kandagatla]

Hi Ulf,
I like to get this patches for v3.16,  any chance of considering these 
patches to v3.16 ?

--srini

On 15/05/14 10:34, srinivas.kandagatla@xxxxxxxxxx wrote:
> From: Srinivas Kandagatla <srinivas.kandagatla@xxxxxxxxxx>
>
> Thankyou everyone for reviewing both RFC and v1 patches.
>
> This patch series adds Qualcomm SD Card Controller support in pl180 mmci
> driver. QCom SDCC is basically a pl180, but bit more customized, some of the
> register layouts and offsets are different to the ones mentioned in pl180
> datasheet. The plan is to totally remove the standalone SDCC driver
> drivers/mmc/host/msm_sdcc.* and start using generic mmci driver for all
> Qualcomm parts, as we get chance to test on other Qcom boards.
>
> To start using the existing mmci driver, a fake amba id for Qualcomm is added
> in patches:
>   mmc: mmci: Add Qualcomm Id to amba id table.
>
> Second change is, adding a 3 clock cycle delay for register writes on QCOM SDCC
> registers, which is done in patches:
>    mmc: mmci: Add register read/write wrappers.
>    mmc: mmci: Qcomm: Add 3 clock cycle delay after register write
>
> Third change is to accommodate CLK, DATCTRL and MMCICLK register layout changes
> in Qcom SDCC and provide more flexibity in driver to specify these changes via
> variant datastructure. Which are done in patches:
>    mmc: mmci: Add Qcom datactrl register variant
>    mmc: mmci: add ddrmode mask to variant data
>    mmc: mmci: add 8bit bus support in variant data
>    mmc: mmci: add edge support to data and command out in variant data.
>    mmc: mmci: add Qcom specifics of clk and datactrl registers.
>    mmc: mmci: Add support to data commands via variant structure.
>    mmc: mmci: add support for fbclk to latch data and cmd.
>    mmc: mmci: add qcom specific clk control
>
> Fourth major change was to add qcom specfic pio read function, the need for
> this is because the way MCIFIFOCNT register behaved in QCOM SDCC is very
>   different to the one in pl180. This change is done in patch:
>    mmc: mmci: Add Qcom specific pio_read function.
>
> Last some Qcom unrelated changes/cleanup to driver are done in patches:
>    mmc: mmci: use NSEC_PER_SEC macro
>    mmc: mmci: convert register bits to use BIT() macro.
>
> This patches are tested in PIO mode on IFC8064 board with both eMMC and
> external SD card. I would like to get this support in v3.16.
>
> Changes from v1:
> 	- moved most of the SOC specifics to variant parameters as suggested
> 	  by Linus W.
> 	- renamed registers as suggested by Linus W.
> 	- Added comments in the code as suggested by Linus W.
> 	- moved out AMBA ID addition patch from this series.
> 	- rebased the patches to
> 		git://git.linaro.org/people/ulf.hansson/mmc.git next
> 	  as suggested by Ulf H.
>
> Changes from RFC:
> 	- moved out clk setup out of spinlock as pointed by Stephen B.
> 	
> Thanks,
> srini
>
> Srinivas Kandagatla (14):
>    mmc: mmci: use NSEC_PER_SEC macro
>    mmc: mmci: convert register bits to use BIT() macro.
>    mmc: mmci: Add Qualcomm Id to amba id table
>    mmc: mmci: Add Qcom datactrl register variant
>    mmc: mmci: Add register read/write wrappers.
>    mmc: mmci: Qcomm: Add 3 clock cycle delay after register write
>    mmc: mmci: add ddrmode mask to variant data
>    mmc: mmci: add 8bit bus support in variant data
>    mmc: mmci: add edge support to data and command out in variant data.
>    mmc: mmci: add Qcom specifics of clk and datactrl registers.
>    mmc: mmci: Add support to data commands via variant structure.
>    mmc: mmci: add support for fbclk to latch data and cmd.
>    mmc: mmci: add qcom specific clk control
>    mmc: mmci: Add Qcom specific pio_read function.
>
>   drivers/mmc/host/mmci.c | 245 ++++++++++++++++++++++++++++++++++++------------
>   drivers/mmc/host/mmci.h | 232 +++++++++++++++++++++++++--------------------
>   2 files changed, 311 insertions(+), 166 deletions(-)
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/