[PATCH/RFC v4 17/21] DT: Add documentation for the mfd Maxim max77693

[Jacek Anaszewski]

This patch adds device tree binding documentation for
the flash cell of the Maxim max77693 multifunctional device.

Signed-off-by: Andrzej Hajda <a.hajda@xxxxxxxxxxx>
Acked-by: Kyungmin Park <kyungmin.park@xxxxxxxxxxx>
Cc: Rob Herring <robh+dt@xxxxxxxxxx>
Cc: Pawel Moll <pawel.moll@xxxxxxx>
Cc: Mark Rutland <mark.rutland@xxxxxxx>
Cc: Ian Campbell <ijc+devicetree@xxxxxxxxxxxxxx>
Cc: Kumar Gala <galak@xxxxxxxxxxxxxx>
---
 Documentation/devicetree/bindings/mfd/max77693.txt |   62 ++++++++++++++++++++
 1 file changed, 62 insertions(+)

diff --git a/Documentation/devicetree/bindings/mfd/max77693.txt b/Documentation/devicetree/bindings/mfd/max77693.txt
index 11921cc..0c3db3d 100644
--- a/Documentation/devicetree/bindings/mfd/max77693.txt
+++ b/Documentation/devicetree/bindings/mfd/max77693.txt
@@ -27,6 +27,55 @@ Optional properties:
 
 	[*] refer Documentation/devicetree/bindings/regulator/regulator.txt
 
+Optional node:
+- led-flash : the LED submodule device node
+
+Required properties of "led-flash" node:
+- compatible : must be "maxim,max77693-flash"
+- maxim,num-leds : number of connected leds
+	Possible values: 1 or 2.
+- maxim,fleds : array of current outputs in order: fled1, fled2
+	Note: both current outputs can be connected to a single led
+	Possible values:
+		0 - the output is left disconnected,
+		1 - a diode is connected to the output.
+
+Optional properties of "led-flash" node:
+- maxim,boost-mode :
+	In boost mode the device can produce up to 1.2A of total current
+	on both outputs. The maximum current on each output is reduced
+	to 625mA then. If maxim,num-leds == <2> boost must be enabled
+	(it defaults to 1 if not set):
+	Possible values:
+		0 - no boost,
+		1 - adaptive mode,
+		2 - fixed mode.
+- iout-torch : Array of maximum intensities in microamperes of the torch
+	led currents in order: fled1, fled2.
+		15625 - 250000
+- iout-flash : Array of maximum intensities in microamperes of the flash
+	led currents in order: fled1, fled2.
+	Range:
+		15625 - 1000000 (max 625000 if boost mode is enabled)
+- flash-timeout : timeout in microseconds after which flash led
+		  is turned off
+	Range:
+		62500 - 1000000
+- maxim,trigger : Array of flags indicating which trigger can activate given led
+	in order: fled1, fled2
+	Possible flag values (can be combined):
+		1 - FLASH pin of the chip,
+		2 - TORCH pin of the chip,
+		4 - software via I2C command.
+- maxim,trigger-type : Array of trigger types in order: flash, torch.
+	Possible trigger types:
+		0 - Rising edge of the signal triggers the flash/torch,
+		1 - Signal level controls duration of the flash/torch.
+- maxim,boost-vout : Output voltage of the boost module in millivolts.
+- maxim,vsys-min : Low input voltage level in millivolts. Flash is not fired
+	if chip estimates that system voltage could drop below this level due
+	to flash power consumption.
+
 Example:
 	max77693@66 {
 		compatible = "maxim,max77693";
@@ -52,4 +101,17 @@ Example:
 					regulator-boot-on;
 			};
 		};
+		led_flash: led-flash {
+			compatible = "maxim,max77693-flash";
+			iout-torch = <500000 0>;
+			iout-flash = <1250000 0>;
+			flash-timeout = <1000000 1000000>;
+			maxim,num-leds = <1>;
+			maxim,fleds = <1 1>;
+			maxim,trigger = <7 7>;
+			maxim,trigger-type = <0 1>;
+			maxim,boost-mode = <1>;
+			maxim,boost-vout = <5000>;
+			maxim,vsys-min = <2400>;
+		};
 	};
-- 
1.7.9.5

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/