[PATCH 93/93] Staging: comedi: adl_pci9118: fixed style issues
From: sam-the-6
Date: Mon Jul 14 2014 - 23:18:19 EST
From: Sam Asadi <asadi.samuel@xxxxxxxxx>
several style issues fixed.
Signed-off-by: Sam Asadi <asadi.samuel@xxxxxxxxx>
modified: drivers/staging/comedi/drivers/adl_pci9118.c
---
drivers/staging/comedi/drivers/adl_pci9118.c | 124 +++++++++++++-------------
1 file changed, 62 insertions(+), 62 deletions(-)
diff --git a/drivers/staging/comedi/drivers/adl_pci9118.c b/drivers/staging/comedi/drivers/adl_pci9118.c
index 59a65cb..7139f87 100644
--- a/drivers/staging/comedi/drivers/adl_pci9118.c
+++ b/drivers/staging/comedi/drivers/adl_pci9118.c
@@ -8,59 +8,63 @@
* Author: Michal Dobes <dobes@xxxxxxxxx>
*
*/
-/*
-Driver: adl_pci9118
-Description: Adlink PCI-9118DG, PCI-9118HG, PCI-9118HR
-Author: Michal Dobes <dobes@xxxxxxxxx>
-Devices: [ADLink] PCI-9118DG (pci9118dg), PCI-9118HG (pci9118hg),
- PCI-9118HR (pci9118hr)
-Status: works
-
-This driver supports AI, AO, DI and DO subdevices.
-AI subdevice supports cmd and insn interface,
-other subdevices support only insn interface.
-For AI:
-- If cmd->scan_begin_src=TRIG_EXT then trigger input is TGIN (pin 46).
-- If cmd->convert_src=TRIG_EXT then trigger input is EXTTRG (pin 44).
-- If cmd->start_src/stop_src=TRIG_EXT then trigger input is TGIN (pin 46).
-- It is not necessary to have cmd.scan_end_arg=cmd.chanlist_len but
- cmd.scan_end_arg modulo cmd.chanlist_len must by 0.
-- If return value of cmdtest is 5 then you've bad channel list
- (it isn't possible mixture S.E. and DIFF inputs or bipolar and unipolar
- ranges).
-
-There are some hardware limitations:
-a) You cann't use mixture of unipolar/bipoar ranges or differencial/single
- ended inputs.
-b) DMA transfers must have the length aligned to two samples (32 bit),
- so there is some problems if cmd->chanlist_len is odd. This driver tries
- bypass this with adding one sample to the end of the every scan and discard
- it on output but this cann't be used if cmd->scan_begin_src=TRIG_FOLLOW
- and is used flag TRIG_WAKE_EOS, then driver switch to interrupt driven mode
- with interrupt after every sample.
-c) If isn't used DMA then you can use only mode where
- cmd->scan_begin_src=TRIG_FOLLOW.
-
-Configuration options:
- [0] - PCI bus of device (optional)
- [1] - PCI slot of device (optional)
- If bus/slot is not specified, then first available PCI
- card will be used.
- [2] - 0= standard 8 DIFF/16 SE channels configuration
- n = external multiplexer connected, 1 <= n <= 256
- [3] - 0=autoselect DMA or EOC interrupts operation
- 1 = disable DMA mode
- 3 = disable DMA and INT, only insn interface will work
- [4] - sample&hold signal - card can generate signal for external S&H board
- 0 = use SSHO(pin 45) signal is generated in onboard hardware S&H logic
- 0 != use ADCHN7(pin 23) signal is generated from driver, number say how
- long delay is requested in ns and sign polarity of the hold
- (in this case external multiplexor can serve only 128 channels)
- [5] - 0=stop measure on all hardware errors
- 2 | = ignore ADOR - A/D Overrun status
- 8|=ignore Bover - A/D Burst Mode Overrun status
- 256|=ignore nFull - A/D FIFO Full status
+/*
+ Driver: adl_pci9118
+ Description: Adlink PCI-9118DG, PCI-9118HG, PCI-9118HR
+ Author: Michal Dobes <dobes@xxxxxxxxx>
+ Devices: [ADLink] PCI-9118DG (pci9118dg), PCI-9118HG (pci9118hg),
+ PCI-9118HR (pci9118hr)
+ Status: works
+
+ This driver supports AI, AO, DI and DO subdevices.
+ AI subdevice supports cmd and insn interface,
+ other subdevices support only insn interface.
+ For AI:
+ - If cmd->scan_begin_src=TRIG_EXT then trigger input is TGIN (pin 46).
+ - If cmd->convert_src=TRIG_EXT then trigger input is EXTTRG (pin 44).
+ - If cmd->start_src/stop_src=TRIG_EXT then trigger input is TGIN (pin 46).
+ - It is not necessary to have cmd.scan_end_arg=cmd.chanlist_len but
+ cmd.scan_end_arg modulo cmd.chanlist_len must by 0.
+ - If return value of cmdtest is 5 then you've bad channel list
+ (it isn't possible mixture S.E. and DIFF inputs or bipolar and unipolar
+ ranges).
+
+ There are some hardware limitations:
+ a) You cann't use mixture of unipolar/bipoar ranges or differencial/single
+ ended inputs.
+ b) DMA transfers must have the length aligned to two samples (32 bit),
+ so there is some problems if cmd->chanlist_len is odd. This driver
+ tries bypass this with adding one sample to the end of the every scan
+ and discard it on output but this cann't be used if
+ cmd->scan_begin_src=TRIG_FOLLOW and is used flag TRIG_WAKE_EOS, then
+ driver switch to interrupt driven mode with interrupt after every
+ sample.
+ c) If isn't used DMA then you can use only mode where
+ cmd->scan_begin_src=TRIG_FOLLOW.
+
+ Configuration options:
+ [0] - PCI bus of device (optional)
+ [1] - PCI slot of device (optional)
+ If bus/slot is not specified, then first available PCI
+ card will be used.
+ [2] - 0= standard 8 DIFF/16 SE channels configuration
+ n = external multiplexer connected, 1 <= n <= 256
+ [3] - 0=autoselect DMA or EOC interrupts operation
+ 1 = disable DMA mode
+ 3 = disable DMA and INT, only insn interface will work
+ [4] - sample&hold signal - card can generate signal for external
+ S&H board
+ 0 = use SSHO(pin 45) signal is generated in onboard hardware
+ S&H logic
+ 0 != use ADCHN7(pin 23) signal is generated from driver, number
+ say how long delay is requested in ns and sign polarity of
+ the hold (in this case external multiplexor can serve only
+ 128 channels)
+ [5] - 0=stop measure on all hardware errors
+ 2 | = ignore ADOR - A/D Overrun status
+ 8|=ignore Bover - A/D Burst Mode Overrun status
+ 256|=ignore nFull - A/D FIFO Full status
*/
/*
@@ -346,7 +350,7 @@ struct pci9118_private {
* on external start
*/
unsigned short ao_data[2]; /* data output buffer */
- char dma_doublebuf; /* we can use double buffering */
+ char dma_doublebuf; /* we can use double buffering */
unsigned int dma_actbuf; /* which buffer is used now */
unsigned short *dmabuf_virt[2]; /*
* pointers to begin of
@@ -399,7 +403,7 @@ static int check_channel_list(struct comedi_device *dev,
}
if ((frontadd + n_chan + backadd) > s->len_chanlist) {
comedi_error(dev,
- "range/channel list is too long for actual configuration!\n");
+ "range/channel list is too long for actual configuration!\n");
return 0;
}
@@ -412,22 +416,19 @@ static int check_channel_list(struct comedi_device *dev,
if ((CR_AREF(chanlist[i]) == AREF_DIFF) !=
(differencial)) {
comedi_error(dev,
- "Differencial and single ended "
- "inputs can't be mixtured!");
+ "Differencial and single ended inputs can't be mixtured!");
return 0;
}
if ((CR_RANGE(chanlist[i]) < PCI9118_BIPOLAR_RANGES) !=
(bipolar)) {
comedi_error(dev,
- "Bipolar and unipolar ranges "
- "can't be mixtured!");
+ "Bipolar and unipolar ranges can't be mixtured!");
return 0;
}
if (!devpriv->usemux && differencial &&
(CR_CHAN(chanlist[i]) >= this_board->n_aichand)) {
comedi_error(dev,
- "If AREF_DIFF is used then is "
- "available only first 8 channels!");
+ "If AREF_DIFF is used then is available only first 8 channels!");
return 0;
}
}
@@ -1678,8 +1679,7 @@ static int pci9118_ai_cmd(struct comedi_device *dev, struct comedi_subdevice *s)
/* double timed action */
if (!devpriv->usedma) {
comedi_error(dev,
- "cmd->scan_begin_src=TRIG_TIMER works "
- "only with bus mastering!");
+ "cmd->scan_begin_src=TRIG_TIMER works only with bus mastering!");
return -EIO;
}
--
1.7.10.4
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/