Re: [PATCH v2 4/4] ARM: dts: exynos5250: Add Spring device tree

From: Andreas FÃrber
Date: Wed Jul 30 2014 - 09:06:47 EST

Next message: Chao Yu: "RE: [f2fs-dev] [PATCH] f2fs: reduce competition among node page writes"
Previous message: Michal Marek: "Re: [PATCH] kbuild, LLVMLinux: only use warnings when using clang"
In reply to: Doug Anderson: "Re: [PATCH v2 4/4] ARM: dts: exynos5250: Add Spring device tree"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

Hi Doug,

Am 25.07.2014 18:02, schrieb Doug Anderson:
> Andreas,
>
> On Fri, Jul 18, 2014 at 10:20 AM, Andreas FÃrber <afaerber@xxxxxxx> wrote:
>> + gpio-keys {
>> + compatible = "gpio-keys";
>> +
>> + power {
>> + label = "Power";
>> + gpios = <&gpx1 3 1>;
>> + linux,code = <116>; /* KEY_POWER */
>> + gpio-key,wakeup;
>> + };
>
> Is the lid switch not working?

No, I don't see any reaction at least. I notice that 3.8 has pinctrls on
gpio-keys directly though...

> Where is your pinctrl?

Maybe that's what you mean here?

> Can you match this in sort order with snow to make diffs easier?

Done.

>> + };
>> +};
>> +
>> +&i2c_0 {
>> + status = "okay";
>> + samsung,i2c-sda-delay = <100>;
>> + samsung,i2c-max-bus-freq = <378000>;
>> +
>> + s5m8767_pmic@66 {
>> + compatible = "samsung,s5m8767-pmic";
>> + reg = <0x66>;
>> + interrupt-parent = <&gpx3>;
>> + interrupts = <2 0>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&s5m8767_irq &s5m8767_dvs &s5m8767_ds>;
>> + wakeup-source;
>> +
>> + s5m8767,pmic-buck-dvs-gpios = <&gpd1 0 1>, /* DVS1 */
>> + <&gpd1 1 1>, /* DVS2 */
>> + <&gpd1 2 1>; /* DVS3 */
>> +
>> + s5m8767,pmic-buck-ds-gpios = <&gpx2 3 1>, /* SET1 */
>> + <&gpx2 4 1>, /* SET2 */
>> + <&gpx2 5 1>; /* SET3 */
>> +
>> + /*
>> + * The following arrays of DVS voltages are not used, since we are
>> + * not using GPIOs to control PMIC bucks, but they must be defined
>> + * to please the driver.
>> + */
>> + s5m8767,pmic-buck2-dvs-voltage = <1350000>, <1300000>,
>> + <1250000>, <1200000>,
>> + <1150000>, <1100000>,
>> + <1000000>, <950000>;
>> +
>> + s5m8767,pmic-buck3-dvs-voltage = <1100000>, <1100000>,
>> + <1100000>, <1100000>,
>> + <1000000>, <1000000>,
>> + <1000000>, <1000000>;
>> +
>> + s5m8767,pmic-buck4-dvs-voltage = <1200000>, <1200000>,
>> + <1200000>, <1200000>,
>> + <1200000>, <1200000>,
>> + <1200000>, <1200000>;
>> +
>> + clocks {
>> + compatible = "samsung,s5m8767-clk";
>> + #clock-cells = <1>;
>> + clock-output-names = "en32khz_ap",
>> + "en32khz_cp",
>> + "en32khz_bt";
>> + };
>> +
>> + regulators {
>> + s5m_ldo4_reg: LDO4 {
>> + regulator-name = "P1.0V_LDO_OUT4";
>> + regulator-min-microvolt = <1000000>;
>> + regulator-max-microvolt = <1000000>;
>> + regulator-always-on;
>> + op_mode = <0>;
>> + };
>> +
>> + s5m_ldo5_reg: LDO5 {
>> + regulator-name = "P1.0V_LDO_OUT5";
>> + regulator-min-microvolt = <1000000>;
>> + regulator-max-microvolt = <1000000>;
>> + regulator-always-on;
>> + op_mode = <0>;
>> + };
>> +
>> + s5m_ldo6_reg: LDO6 {
>> + regulator-name = "vdd_mydp";
>> + regulator-min-microvolt = <1000000>;
>> + regulator-max-microvolt = <1000000>;
>> + regulator-always-on;
>> + op_mode = <3>;
>> + };
>> +
>> + s5m_ldo7_reg: LDO7 {
>> + regulator-name = "P1.1V_LDO_OUT7";
>> + regulator-min-microvolt = <1100000>;
>> + regulator-max-microvolt = <1100000>;
>> + regulator-always-on;
>> + op_mode = <3>;
>> + };
>> +
>> + s5m_ldo8_reg: LDO8 {
>> + regulator-name = "P1.0V_LDO_OUT8";
>> + regulator-min-microvolt = <1000000>;
>> + regulator-max-microvolt = <1000000>;
>> + regulator-always-on;
>> + op_mode = <3>;
>> + };
>> +
>> + s5m_ldo10_reg: LDO10 {
>> + regulator-name = "P1.8V_LDO_OUT10";
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + regulator-always-on;
>> + op_mode = <3>;
>> + };
>> +
>> + s5m_ldo11_reg: LDO11 {
>> + regulator-name = "P1.8V_LDO_OUT11";
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + regulator-always-on;
>> + op_mode = <0>;
>> + };
>> +
>> + s5m_ldo12_reg: LDO12 {
>> + regulator-name = "P3.0V_LDO_OUT12";
>> + regulator-min-microvolt = <3000000>;
>> + regulator-max-microvolt = <3000000>;
>> + regulator-always-on;
>> + op_mode = <3>;
>> + };
>> +
>> + s5m_ldo13_reg: LDO13 {
>> + regulator-name = "P1.8V_LDO_OUT13";
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + regulator-always-on;
>> + op_mode = <0>;
>> + };
>> +
>> + s5m_ldo14_reg: LDO14 {
>> + regulator-name = "P1.8V_LDO_OUT14";
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + regulator-always-on;
>> + op_mode = <3>;
>> + };
>> +
>> + s5m_ldo15_reg: LDO15 {
>> + regulator-name = "P1.0V_LDO_OUT15";
>> + regulator-min-microvolt = <1000000>;
>> + regulator-max-microvolt = <1000000>;
>> + regulator-always-on;
>> + op_mode = <3>;
>> + };
>> +
>> + s5m_ldo16_reg: LDO16 {
>> + regulator-name = "P1.8V_LDO_OUT16";
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + regulator-always-on;
>> + op_mode = <3>;
>> + };
>> +
>> + s5m_ldo17_reg: LDO17 {
>> + regulator-name = "P2.8V_LDO_OUT17";
>> + regulator-min-microvolt = <2800000>;
>> + regulator-max-microvolt = <2800000>;
>> + regulator-always-on;
>> + op_mode = <0>;
>> + };
>> +
>> + s5m_ldo25_reg: LDO25 {
>> + regulator-name = "vdd_bridge";
>> + regulator-min-microvolt = <1200000>;
>> + regulator-max-microvolt = <1200000>;
>> + regulator-always-on;
>> + op_mode = <1>;
>> + };
>> +
>> + BUCK1 {
>> + regulator-name = "vdd_mif";
>> + regulator-min-microvolt = <950000>;
>> + regulator-max-microvolt = <1300000>;
>> + regulator-always-on;
>> + regulator-boot-on;
>> + op_mode = <3>;
>> + };
>> +
>> + BUCK2 {
>> + regulator-name = "vdd_arm";
>> + regulator-min-microvolt = <850000>;
>> + regulator-max-microvolt = <1350000>;
>> + regulator-always-on;
>> + regulator-boot-on;
>> + op_mode = <3>;
>> + };
>> +
>> + BUCK3 {
>> + regulator-name = "vdd_int";
>> + regulator-min-microvolt = <900000>;
>> + regulator-max-microvolt = <1200000>;
>> + regulator-always-on;
>> + regulator-boot-on;
>> + op_mode = <3>;
>> + };
>> +
>> + BUCK4 {
>> + regulator-name = "vdd_g3d";
>> + regulator-min-microvolt = <850000>;
>> + regulator-max-microvolt = <1300000>;
>> + regulator-boot-on;
>> + op_mode = <3>;
>> + };
>> +
>> + BUCK5 {
>> + regulator-name = "P1.8V_BUCK_OUT5";
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + regulator-always-on;
>> + regulator-boot-on;
>> + op_mode = <1>;
>> + };
>> +
>> + BUCK6 {
>> + regulator-name = "P1.2V_BUCK_OUT6";
>> + regulator-min-microvolt = <1200000>;
>> + regulator-max-microvolt = <1200000>;
>> + regulator-always-on;
>> + regulator-boot-on;
>> + op_mode = <0>;
>> + };
>> +
>> + BUCK9 {
>> + regulator-name = "vdd_ummc";
>> + regulator-min-microvolt = <950000>;
>> + regulator-max-microvolt = <3000000>;
>> + regulator-always-on;
>> + regulator-boot-on;
>> + op_mode = <3>;
>> + };
>> + };
>> + };
>> +};
>> +
>> +&i2c_1 {
>> + status = "okay";
>> + samsung,i2c-sda-delay = <100>;
>> + samsung,i2c-max-bus-freq = <378000>;
>> +};
>> +
>> +&i2c_2 {
>> + status = "okay";
>> + samsung,i2c-sda-delay = <100>;
>> + samsung,i2c-max-bus-freq = <66000>;
>> +
>> + hdmiddc@50 {
>> + compatible = "samsung,exynos4210-hdmiddc";
>> + reg = <0x50>;
>> + };
>> +};
>> +
>> +&i2c_3 {
>> + status = "okay";
>> + samsung,i2c-sda-delay = <100>;
>> + samsung,i2c-max-bus-freq = <66000>;
>> +};
>> +
>> +&i2c_4 {
>> + status = "okay";
>> + samsung,i2c-sda-delay = <100>;
>> + samsung,i2c-max-bus-freq = <66000>;
>> +
>> + cros_ec: embedded-controller {
>> + compatible = "google,cros-ec-i2c";
>> + reg = <0x1e>;
>> + interrupts = <6 0>;
>> + interrupt-parent = <&gpx1>;
>
> I think you want a pinctrl for gpx1-6, like Snow's "ec_irq".

Done. On v1 you had asked about a pinctrl for the keyboard, which has
none, but cros_ec itself does in fact.

>> + wakeup-source;
>> + };
>> +};
>> +
>> +&i2c_5 {
>> + status = "okay";
>> + samsung,i2c-sda-delay = <100>;
>> + samsung,i2c-max-bus-freq = <66000>;
>> +};
>> +
>> +&i2c_7 {
>> + status = "okay";
>> + samsung,i2c-sda-delay = <100>;
>> + samsung,i2c-max-bus-freq = <66000>;
>> +};
>> +
>> +&i2c_8 {
>> + status = "okay";
>> + samsung,i2c-sda-delay = <100>;
>> + samsung,i2c-max-bus-freq = <378000>;
>> +
>> + hdmiphy: hdmiphy@38 {
>> + compatible = "samsung,exynos4212-hdmiphy";
>> + reg = <0x38>;
>> + };
>> +};
>> +
>> +&mmc_0 {
>> + status = "okay";
>> + num-slots = <1>;
>> + supports-highspeed;
>> + broken-cd;
>> + card-detect-delay = <200>;
>> + samsung,dw-mshc-ciu-div = <3>;
>> + samsung,dw-mshc-sdr-timing = <2 3>;
>> + samsung,dw-mshc-ddr-timing = <1 2>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_cd &sd0_bus4 &sd0_bus8>;
>> +
>> + slot@0 {
>> + reg = <0>;
>> + bus-width = <8>;
>> + };
>> +};
>> +
>> +&mmc_1 {
>> + status = "okay";
>> + num-slots = <1>;
>> + supports-highspeed;
>> + broken-cd;
>> + card-detect-delay = <200>;
>> + samsung,dw-mshc-ciu-div = <3>;
>> + samsung,dw-mshc-sdr-timing = <2 3>;
>> + samsung,dw-mshc-ddr-timing = <1 2>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&sd1_clk &sd1_cmd &sd1_cd &sd1_bus4>;
>> +
>> + slot@0 {
>> + reg = <0>;
>> + bus-width = <4>;
>> + };
>> +};
>
> mmc_1 on Spring matches with mmc_3 on Snow. That means you need to
> make sure you've got the reduced drive strengths, too. I don't think
> your device tree has these. Specifically you need local overrides of
> sd1_clk, sd1_cmd, etc to lower drive strengths.

Done. Wasn't sure about _cd, so I included it.

>> +
>> +&mmc_2 {
>> + /* MMC2 pins are used as GPIO for eDP bridge control. */
>> + status = "disabled";
>> +};
>
> Remove the mmc_2 reference. It's disabled in exynos5250.dtsi already.

Done. That drops the documentation of why, too, though.

>> +
>> +&pinctrl_0 {
>> + /*
>> + * Disabled pullups since external part has its own pullups and
>> + * double-pulling gets us out of spec in some cases.
>> + */
>> + i2c2_bus: i2c2-bus {
>> + samsung,pin-pud = <0>;
>> + };
>> +
>> + s5m8767_dvs: s5m8767-dvs {
>> + samsung,pins = "gpd1-0", "gpd1-1", "gpd1-2";
>> + samsung,pin-function = <0>;
>> + samsung,pin-pud = <1>;
>> + samsung,pin-drv = <0>;
>> + };
>> +
>> + s5m8767_ds: s5m8767-ds {
>> + samsung,pins = "gpx2-3", "gpx2-4", "gpx2-5";
>> + samsung,pin-function = <0>;
>> + samsung,pin-pud = <1>;
>> + samsung,pin-drv = <0>;
>> + };
>> +
>> + s5m8767_irq: s5m8767-irq {
>> + samsung,pins = "gpx3-2";
>> + samsung,pin-function = <0>;
>> + samsung,pin-pud = <0>;
>> + samsung,pin-drv = <0>;
>> + };
>> +
>> + hdmi_hpd_irq: hdmi-hpd-irq {
>> + samsung,pins = "gpx3-7";
>> + samsung,pin-function = <0>;
>> + samsung,pin-pud = <1>;
>> + samsung,pin-drv = <0>;
>> + };
>
> Ideally you could do one more cleanup patch to snow first to make
> diffs easier between the two dts files. Moving things in the snow
> file from "pinctrl@11400000" to the pinctrl_0 section would help.
> ...and other cleanups you could do to snow to make diffs similar would
> also be really great.

Done.

>> +};
>> +
>> +&pinctrl_1 {
>> + hsic_reset: hsic-reset {
>> + samsung,pins = "gpe1-0";
>> + samsung,pin-function = <1>;
>> + samsung,pin-pud = <0>;
>> + samsung,pin-drv = <0>;
>> + };
>> +};
>> +
>> +&spi_1 {
>> + status = "okay";
>> + samsung,spi-src-clk = <0>;
>> + num-cs = <1>;
>> +};
>> +
>> +&usbdrd_phy {
>> + vbus-supply = <&usb3_vbus_reg>;
>> +};
>> +
>> +#include "cros-ec-keyboard.dtsi"
>> --
>> 1.9.3

Also found some unresolved review comments from v1 that I incorporated.

Regards,
Andreas

--
SUSE LINUX Products GmbH, Maxfeldstr. 5, 90409 NÃrnberg, Germany
GF: Jeff Hawn, Jennifer Guild, Felix ImendÃrffer; HRB 16746 AG NÃrnberg
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

Next message: Chao Yu: "RE: [f2fs-dev] [PATCH] f2fs: reduce competition among node page writes"
Previous message: Michal Marek: "Re: [PATCH] kbuild, LLVMLinux: only use warnings when using clang"
In reply to: Doug Anderson: "Re: [PATCH v2 4/4] ARM: dts: exynos5250: Add Spring device tree"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]