[PATCH v5 10/10] ARM: dts: Add exynos5250-spring device tree

From: Andreas FÃrber
Date: Fri Aug 01 2014 - 00:57:16 EST

Adds initial support for the HP Chromebook 11.

Cc: Vincent Palatin <vpalatin@xxxxxxxxxxxx>
Cc: Doug Anderson <dianders@xxxxxxxxxxxx>
Cc: Stephan van Schaik <stephan@xxxxxxxxxxxxxx>
Signed-off-by: Andreas FÃrber <afaerber@xxxxxxx>
---
v4 -> v5:
* Dropped bogus USB3 regulator (Vincent Palatin, Tomasz Figa)
* Fixed USB3503 reset GPIO (Tomasz Figa)
* Introduced labels to use new referencing style consistently (Tomasz Figa)
* Don't override dp_hpd, moved to pinctrl_0 instead (Tomasz Figa)
* mmc_1: Added comment from Snow's mmc_3 (Tomasz Figa / Doug Anderson)
* Override /codec samsung,mfc-{l,r} properties for alignment with Arndale
* Use more GPIO_ACTIVE_* constants
* Use IRQ_TYPE_* constants
* Dropped s5m_ prefix for s5m8767 LDO regulator labels (max77686 is gone)
* Labeled also all s5m8767 BUCK regulators

v3 -> v4:
* Fixed samsung,pin-function 1 -> 0 for dp-hpd-gpio
* Replaced dp-hpd-gpio with existing dp_hpd, overriding it

v2 -> v3:
* Use GPIO_ACTIVE_{LOW,HIGH} (Doug Anderson)
* Use symbolic KEY_POWER instead of comment
* Moved hsic_reset to new USB3503 node's reset-gpios (Vincent Palatin)
* Use dp_hpd_gpio for dp-controller (Doug Anderson, Ajay Kumar)
* Override sd1_{clk,cmd,cd,bus4} pinctrl similar to Snow (Doug Anderson)
* Added ec_irq pinctrl for cros_ec (Doug Anderson)
* Reordered nodes to minimize diff against Snow (Doug Anderson)
* Dropped obsolete mmc_2 override (Doug Anderson)
* Added lid-switch node (Doug Anderson)
* Added gpio-keys pinctrl (Doug Anderson)
* Added bootargs to avoid empty /chosen node and to document console setting
* Renamed s5m8767_pmic node to avoid underscore
* Use new style for overriding inherited pinctrl nodes, too
* Enable i2s0 node

v1 -> v2:
* Use label-based overriding/extension of nodes. (Doug Anderson)
* Dropped tps65090 for now, until we know where to place it.
* Dropped non-Spring nodes from -cros-common.dtsi rather than disabling them.
* Enabled a missing MMC node for access to internal storage.
* Dropped display-timings from dp-controller node. (Ajay Kumar)

arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/exynos5250-spring.dts | 536 ++++++++++++++++++++++++++++++++
2 files changed, 537 insertions(+)
create mode 100644 arch/arm/boot/dts/exynos5250-spring.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 80a781f76e88..dec4c292f63d 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -76,6 +76,7 @@ dtb-$(CONFIG_ARCH_EXYNOS) += exynos4210-origen.dtb \
exynos5250-arndale.dtb \
exynos5250-smdk5250.dtb \
exynos5250-snow.dtb \
+ exynos5250-spring.dtb \
exynos5260-xyref5260.dtb \
exynos5410-smdk5410.dtb \
exynos5420-arndale-octa.dtb \
diff --git a/arch/arm/boot/dts/exynos5250-spring.dts b/arch/arm/boot/dts/exynos5250-spring.dts
new file mode 100644
index 000000000000..108e3a9002e7
--- /dev/null
+++ b/arch/arm/boot/dts/exynos5250-spring.dts
@@ -0,0 +1,536 @@
+/*
+ * Google Spring board device tree source
+ *
+ * Copyright (c) 2013 Google, Inc
+ * Copyright (c) 2014 SUSE LINUX Products GmbH
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/input/input.h>
+#include "exynos5250.dtsi"
+
+/ {
+ model = "Google Spring";
+ compatible = "google,spring", "samsung,exynos5250", "samsung,exynos5";
+
+ memory {
+ reg = <0x40000000 0x80000000>;
+ };
+
+ chosen {
+ bootargs = "console=tty1";
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&power_key_irq>, <&lid_irq>;
+
+ power {
+ label = "Power";
+ gpios = <&gpx1 3 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_POWER>;
+ gpio-key,wakeup;
+ };
+
+ lid-switch {
+ label = "Lid";
+ gpios = <&gpx3 5 GPIO_ACTIVE_LOW>;
+ linux,input-type = <5>; /* EV_SW */
+ linux,code = <0>; /* SW_LID */
+ debounce-interval = <1>;
+ gpio-key,wakeup;
+ };
+ };
+
+ usb-hub {
+ compatible = "smsc,usb3503a";
+ reset-gpios = <&gpe1 0 GPIO_ACTIVE_LOW>;
+ };
+
+ fixed-rate-clocks {
+ xxti {
+ compatible = "samsung,clock-xxti";
+ clock-frequency = <24000000>;
+ };
+ };
+};
+
+&codec {
+ samsung,mfc-r = <0x43000000 0x800000>;
+ samsung,mfc-l = <0x51000000 0x800000>;
+};
+
+&dp {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&dp_hpd>;
+ samsung,color-space = <0>;
+ samsung,dynamic-range = <0>;
+ samsung,ycbcr-coeff = <0>;
+ samsung,color-depth = <1>;
+ samsung,link-rate = <0x0a>;
+ samsung,lane-count = <1>;
+ samsung,hpd-gpio = <&gpc3 0 GPIO_ACTIVE_HIGH>;
+};
+
+&ehci {
+ samsung,vbus-gpio = <&gpx1 1 GPIO_ACTIVE_HIGH>;
+};
+
+&fimd {
+ status = "okay";
+ samsung,invert-vclk;
+};
+
+&hdmi {
+ hpd-gpio = <&gpx3 7 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&hdmi_hpd_irq>;
+ phy = <&hdmiphy>;
+ ddc = <&i2c_2>;
+ hdmi-en-supply = <&ldo8_reg>;
+ vdd-supply = <&ldo8_reg>;
+ vdd_osc-supply = <&ldo10_reg>;
+ vdd_pll-supply = <&ldo8_reg>;
+};
+
+&i2c_0 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <378000>;
+
+ s5m8767-pmic@66 {
+ compatible = "samsung,s5m8767-pmic";
+ reg = <0x66>;
+ interrupt-parent = <&gpx3>;
+ interrupts = <2 IRQ_TYPE_NONE>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&s5m8767_irq &s5m8767_dvs &s5m8767_ds>;
+ wakeup-source;
+
+ s5m8767,pmic-buck-dvs-gpios = <&gpd1 0 GPIO_ACTIVE_LOW>, /* DVS1 */
+ <&gpd1 1 GPIO_ACTIVE_LOW>, /* DVS2 */
+ <&gpd1 2 GPIO_ACTIVE_LOW>; /* DVS3 */
+
+ s5m8767,pmic-buck-ds-gpios = <&gpx2 3 GPIO_ACTIVE_LOW>, /* SET1 */
+ <&gpx2 4 GPIO_ACTIVE_LOW>, /* SET2 */
+ <&gpx2 5 GPIO_ACTIVE_LOW>; /* SET3 */
+
+ /*
+ * The following arrays of DVS voltages are not used, since we are
+ * not using GPIOs to control PMIC bucks, but they must be defined
+ * to please the driver.
+ */
+ s5m8767,pmic-buck2-dvs-voltage = <1350000>, <1300000>,
+ <1250000>, <1200000>,
+ <1150000>, <1100000>,
+ <1000000>, <950000>;
+
+ s5m8767,pmic-buck3-dvs-voltage = <1100000>, <1100000>,
+ <1100000>, <1100000>,
+ <1000000>, <1000000>,
+ <1000000>, <1000000>;
+
+ s5m8767,pmic-buck4-dvs-voltage = <1200000>, <1200000>,
+ <1200000>, <1200000>,
+ <1200000>, <1200000>,
+ <1200000>, <1200000>;
+
+ clocks {
+ compatible = "samsung,s5m8767-clk";
+ #clock-cells = <1>;
+ clock-output-names = "en32khz_ap",
+ "en32khz_cp",
+ "en32khz_bt";
+ };
+
+ regulators {
+ ldo4_reg: LDO4 {
+ regulator-name = "P1.0V_LDO_OUT4";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ op_mode = <0>;
+ };
+
+ ldo5_reg: LDO5 {
+ regulator-name = "P1.0V_LDO_OUT5";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ op_mode = <0>;
+ };
+
+ ldo6_reg: LDO6 {
+ regulator-name = "vdd_mydp";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ op_mode = <3>;
+ };
+
+ ldo7_reg: LDO7 {
+ regulator-name = "P1.1V_LDO_OUT7";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ op_mode = <3>;
+ };
+
+ ldo8_reg: LDO8 {
+ regulator-name = "P1.0V_LDO_OUT8";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ op_mode = <3>;
+ };
+
+ ldo10_reg: LDO10 {
+ regulator-name = "P1.8V_LDO_OUT10";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ op_mode = <3>;
+ };
+
+ ldo11_reg: LDO11 {
+ regulator-name = "P1.8V_LDO_OUT11";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ op_mode = <0>;
+ };
+
+ ldo12_reg: LDO12 {
+ regulator-name = "P3.0V_LDO_OUT12";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+ op_mode = <3>;
+ };
+
+ ldo13_reg: LDO13 {
+ regulator-name = "P1.8V_LDO_OUT13";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ op_mode = <0>;
+ };
+
+ ldo14_reg: LDO14 {
+ regulator-name = "P1.8V_LDO_OUT14";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ op_mode = <3>;
+ };
+
+ ldo15_reg: LDO15 {
+ regulator-name = "P1.0V_LDO_OUT15";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ op_mode = <3>;
+ };
+
+ ldo16_reg: LDO16 {
+ regulator-name = "P1.8V_LDO_OUT16";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ op_mode = <3>;
+ };
+
+ ldo17_reg: LDO17 {
+ regulator-name = "P2.8V_LDO_OUT17";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ op_mode = <0>;
+ };
+
+ ldo25_reg: LDO25 {
+ regulator-name = "vdd_bridge";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ op_mode = <1>;
+ };
+
+ buck1_reg: BUCK1 {
+ regulator-name = "vdd_mif";
+ regulator-min-microvolt = <950000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <3>;
+ };
+
+ buck2_reg: BUCK2 {
+ regulator-name = "vdd_arm";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <3>;
+ };
+
+ buck3_reg: BUCK3 {
+ regulator-name = "vdd_int";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <3>;
+ };
+
+ buck4_reg: BUCK4 {
+ regulator-name = "vdd_g3d";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-boot-on;
+ op_mode = <3>;
+ };
+
+ buck5_reg: BUCK5 {
+ regulator-name = "P1.8V_BUCK_OUT5";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <1>;
+ };
+
+ buck6_reg: BUCK6 {
+ regulator-name = "P1.2V_BUCK_OUT6";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <0>;
+ };
+
+ buck9_reg: BUCK9 {
+ regulator-name = "vdd_ummc";
+ regulator-min-microvolt = <950000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <3>;
+ };
+ };
+ };
+};
+
+&i2c_1 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <378000>;
+};
+
+/*
+ * Disabled pullups since external part has its own pullups and
+ * double-pulling gets us out of spec in some cases.
+ */
+&i2c2_bus {
+ samsung,pin-pud = <0>;
+};
+
+&i2c_2 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <66000>;
+
+ hdmiddc@50 {
+ compatible = "samsung,exynos4210-hdmiddc";
+ reg = <0x50>;
+ };
+};
+
+&i2c_3 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <66000>;
+};
+
+&i2c_4 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <66000>;
+
+ cros_ec: embedded-controller {
+ compatible = "google,cros-ec-i2c";
+ reg = <0x1e>;
+ interrupts = <6 IRQ_TYPE_NONE>;
+ interrupt-parent = <&gpx1>;
+ wakeup-source;
+ pinctrl-names = "default";
+ pinctrl-0 = <&ec_irq>;
+ };
+};
+
+&i2c_5 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <66000>;
+};
+
+&i2c_7 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <66000>;
+};
+
+&i2c_8 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <378000>;
+
+ hdmiphy: hdmiphy@38 {
+ compatible = "samsung,exynos4212-hdmiphy";
+ reg = <0x38>;
+ };
+};
+
+&i2s0 {
+ status = "okay";
+};
+
+&mmc_0 {
+ status = "okay";
+ num-slots = <1>;
+ supports-highspeed;
+ broken-cd;
+ card-detect-delay = <200>;
+ samsung,dw-mshc-ciu-div = <3>;
+ samsung,dw-mshc-sdr-timing = <2 3>;
+ samsung,dw-mshc-ddr-timing = <1 2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_cd &sd0_bus4 &sd0_bus8>;
+
+ slot@0 {
+ reg = <0>;
+ bus-width = <8>;
+ };
+};
+
+/*
+ * On Spring we've got SIP WiFi and so can keep drive strengths low to
+ * reduce EMI.
+ */
+&mmc_1 {
+ status = "okay";
+ num-slots = <1>;
+ supports-highspeed;
+ broken-cd;
+ card-detect-delay = <200>;
+ samsung,dw-mshc-ciu-div = <3>;
+ samsung,dw-mshc-sdr-timing = <2 3>;
+ samsung,dw-mshc-ddr-timing = <1 2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd1_clk &sd1_cmd &sd1_cd &sd1_bus4>;
+
+ slot@0 {
+ reg = <0>;
+ bus-width = <4>;
+ };
+};
+
+&pinctrl_0 {
+ s5m8767_dvs: s5m8767-dvs {
+ samsung,pins = "gpd1-0", "gpd1-1", "gpd1-2";
+ samsung,pin-function = <0>;
+ samsung,pin-pud = <1>;
+ samsung,pin-drv = <0>;
+ };
+
+ dp_hpd: dp-hpd {
+ samsung,pins = "gpc3-0";
+ samsung,pin-function = <0>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
+
+ power_key_irq: power-key-irq {
+ samsung,pins = "gpx1-3";
+ samsung,pin-function = <0>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ ec_irq: ec-irq {
+ samsung,pins = "gpx1-6";
+ samsung,pin-function = <0>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ s5m8767_ds: s5m8767-ds {
+ samsung,pins = "gpx2-3", "gpx2-4", "gpx2-5";
+ samsung,pin-function = <0>;
+ samsung,pin-pud = <1>;
+ samsung,pin-drv = <0>;
+ };
+
+ s5m8767_irq: s5m8767-irq {
+ samsung,pins = "gpx3-2";
+ samsung,pin-function = <0>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ lid_irq: lid-irq {
+ samsung,pins = "gpx3-5";
+ samsung,pin-function = <0>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ hdmi_hpd_irq: hdmi-hpd-irq {
+ samsung,pins = "gpx3-7";
+ samsung,pin-function = <0>;
+ samsung,pin-pud = <1>;
+ samsung,pin-drv = <0>;
+ };
+};
+
+&pinctrl_1 {
+ hsic_reset: hsic-reset {
+ samsung,pins = "gpe1-0";
+ samsung,pin-function = <1>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+};
+
+&sd1_clk {
+ samsung,pin-drv = <0>;
+};
+
+&sd1_cmd {
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+};
+
+&sd1_cd {
+ samsung,pin-drv = <0>;
+};
+
+&sd1_bus4 {
+ samsung,pin-drv = <0>;
+};
+
+&spi_1 {
+ status = "okay";
+ samsung,spi-src-clk = <0>;
+ num-cs = <1>;
+};
+
+#include "cros-ec-keyboard.dtsi"
--
1.9.3

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/