[PATCH v3 4/6] pinctrl: Qualcomm SPMI PMIC pin controller driver

[Ivan T. Ivanov]

From: "Ivan T. Ivanov" <iivanov@xxxxxxxxxx>

This is the pinctrl, pinmux, pinconf and gpiolib driver for the
Qualcomm GPIO and MPP sub-function blocks found in the PMIC chips.

Signed-off-by: Ivan T. Ivanov <iivanov@xxxxxxxxxx>
---
 drivers/pinctrl/qcom/Kconfig             |   12 +
 drivers/pinctrl/qcom/Makefile            |    1 +
 drivers/pinctrl/qcom/pinctrl-spmi-pmic.c | 1532 ++++++++++++++++++++++++++++++
 3 files changed, 1545 insertions(+)
 create mode 100644 drivers/pinctrl/qcom/pinctrl-spmi-pmic.c

diff --git a/drivers/pinctrl/qcom/Kconfig b/drivers/pinctrl/qcom/Kconfig
index 6bd4e4d..8a24fae 100644
--- a/drivers/pinctrl/qcom/Kconfig
+++ b/drivers/pinctrl/qcom/Kconfig
@@ -39,6 +39,18 @@ config PINCTRL_MSM8X74
 	  This is the pinctrl, pinmux, pinconf and gpiolib driver for the
 	  Qualcomm TLMM block found in the Qualcomm 8974 platform.
 
+config PINCTRL_SPMI_PMIC
+       tristate "Qualcomm SPMI PMIC pin controller driver"
+       depends on GPIOLIB && OF
+       select PINMUX
+       select PINCONF
+       select GENERIC_PINCONF
+       help
+         This is the pinctrl, pinmux, pinconf and gpiolib driver for the
+         Qualcomm GPIO and MPP blocks found in the Qualcomm PMIC's chips,
+         which are using SPMI for communication with SoC. Example PMIC's
+         devices are pm8841, pm8941 and pma8084.
+
 config PINCTRL_SSBI_PMIC
        tristate "Qualcomm SSBI PMIC pin controller driver"
        depends on GPIOLIB && OF
diff --git a/drivers/pinctrl/qcom/Makefile b/drivers/pinctrl/qcom/Makefile
index 8faa2ca..d098058 100644
--- a/drivers/pinctrl/qcom/Makefile
+++ b/drivers/pinctrl/qcom/Makefile
@@ -4,4 +4,5 @@ obj-$(CONFIG_PINCTRL_APQ8064)	+= pinctrl-apq8064.o
 obj-$(CONFIG_PINCTRL_IPQ8064)	+= pinctrl-ipq8064.o
 obj-$(CONFIG_PINCTRL_MSM8960)	+= pinctrl-msm8960.o
 obj-$(CONFIG_PINCTRL_MSM8X74)	+= pinctrl-msm8x74.o
+obj-$(CONFIG_PINCTRL_SPMI_PMIC)	+= pinctrl-spmi-pmic.o
 obj-$(CONFIG_PINCTRL_SSBI_PMIC) += pinctrl-ssbi-pmic.o
diff --git a/drivers/pinctrl/qcom/pinctrl-spmi-pmic.c b/drivers/pinctrl/qcom/pinctrl-spmi-pmic.c
new file mode 100644
index 0000000..ba19979
--- /dev/null
+++ b/drivers/pinctrl/qcom/pinctrl-spmi-pmic.c
@@ -0,0 +1,1532 @@
+/* Copyright (c) 2012-2014, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/export.h>
+#include <linux/gpio.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_gpio.h>
+#include <linux/pinctrl/pinconf-generic.h>
+#include <linux/pinctrl/pinconf.h>
+#include <linux/pinctrl/pinmux.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+#include <linux/types.h>
+
+#include <dt-bindings/pinctrl/qcom,pmic-mpp.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+
+#include "../core.h"
+#include "../pinctrl-utils.h"
+
+/*
+ * Mode select - indicates whether the pin should be input, output, or both
+ * for GPIOs. MPP pins also support bidirectional, analog input, analog output
+ * and current sink.
+ */
+#define QPNP_PIN_MODE_DIG_IN			0
+#define QPNP_PIN_MODE_DIG_OUT			1
+#define QPNP_PIN_MODE_DIG_IN_OUT		2
+#define QPNP_PIN_MODE_BIDIR			3
+#define QPNP_PIN_MODE_AIN			4
+#define QPNP_PIN_MODE_AOUT			5
+#define QPNP_PIN_MODE_SINK			6
+
+/*
+ * Voltage select (GPIO, MPP) - specifies the voltage level when the output
+ * is set to 1. For an input GPIO specifies the voltage level at which
+ * the input is interpreted as a logical 1
+ * To be used with "power-func = <>"
+ */
+#define QPNP_PIN_VIN_4CH_INVALID		5
+#define QPNP_PIN_VIN_8CH_INVALID		8
+
+/*
+ * Analog Output - Set the analog output reference.
+ * See PM8XXX_MPP_AOUT_XXX. To be used with "qcom,aout = <>"
+ */
+#define QPNP_MPP_AOUT_INVALID			8
+
+/*
+ * Analog Input - Set the func for analog input.
+ * See PM8XXX_MPP_AIN_XXX. To be used with "qcom,ain = <>"
+ */
+#define QPNP_MPP_AIN_INVALID			8
+
+/*
+ * Output type - indicates pin should be configured as CMOS or
+ * open drain.
+ */
+#define QPNP_GPIO_OUT_BUF_CMOS			0
+#define QPNP_GPIO_OUT_BUF_OPEN_DRAIN_NMOS	1
+#define QPNP_GPIO_OUT_BUF_OPEN_DRAIN_PMOS	2
+
+/*
+ * Pull Up Values - it indicates whether a pull up or pull down
+ * should be applied. If a pull-up is required the current strength needs
+ * to be specified. Current values of 30uA, 1.5uA, 31.5uA, 1.5uA with 30uA
+ * boost are supported.
+ * Note that the hardware ignores this configuration if the GPIO is not set
+ * to input or output open-drain mode.
+ */
+#define QPNP_GPIO_PULL_UP_30			0
+#define QPNP_GPIO_PULL_UP_1P5			1
+#define QPNP_GPIO_PULL_UP_31P5			2
+#define QPNP_GPIO_PULL_UP_1P5_30		3
+#define QPNP_GPIO_PULL_DN			4
+#define QPNP_GPIO_PULL_NO			5
+
+/*
+ * Pull Up Values - it indicates whether a pull-up should be
+ * applied for bidirectional mode only. The hardware ignores the
+ * configuration when operating in other modes.
+ */
+#define QPNP_MPP_PULL_UP_0P6KOHM		0
+#define QPNP_MPP_PULL_UP_10KOHM			1
+#define QPNP_MPP_PULL_UP_30KOHM			2
+#define QPNP_MPP_PULL_UP_OPEN			3
+
+/* Out Strength (GPIO) - the amount of current supplied for an output GPIO */
+#define QPNP_GPIO_STRENGTH_LOW			1
+#define QPNP_GPIO_STRENGTH_MED			2
+#define QPNP_GPIO_STRENGTH_HIGH			3
+
+/*
+ * Master enable (GPIO, MPP) - Enable features within the pin block based on
+ * configurations. QPNP_PIN_MASTER_DISABLE = Completely disable the pin
+ * lock and let the pin float with high impedance regardless of other settings.
+ */
+#define QPNP_PIN_MASTER_DISABLE                 0
+#define QPNP_PIN_MASTER_ENABLE			1
+
+/* revision registers base address offsets */
+#define QPNP_REG_DIG_MINOR_REV			0x0
+#define QPNP_REG_DIG_MAJOR_REV			0x1
+#define QPNP_REG_ANA_MINOR_REV			0x2
+
+/* type registers base address offsets */
+#define QPNP_REG_TYPE				0x4
+#define QPNP_REG_SUBTYPE			0x5
+
+/* GPIO peripheral type and subtype values */
+#define QPNP_GPIO_TYPE				0x10
+#define QPNP_GPIO_SUBTYPE_GPIO_4CH		0x1
+#define QPNP_GPIO_SUBTYPE_GPIOC_4CH		0x5
+#define QPNP_GPIO_SUBTYPE_GPIO_8CH		0x9
+#define QPNP_GPIO_SUBTYPE_GPIOC_8CH		0xd
+
+/* mpp peripheral type and subtype values */
+#define QPNP_MPP_TYPE				0x11
+#define QPNP_MPP_SUBTYPE_4CH_NO_ANA_OUT		0x3
+#define QPNP_MPP_SUBTYPE_ULT_4CH_NO_ANA_OUT	0x4
+#define QPNP_MPP_SUBTYPE_4CH_NO_SINK		0x5
+#define QPNP_MPP_SUBTYPE_ULT_4CH_NO_SINK	0x6
+#define QPNP_MPP_SUBTYPE_4CH_FULL_FUNC		0x7
+#define QPNP_MPP_SUBTYPE_8CH_FULL_FUNC		0xf
+
+#define QPNP_REG_STATUS1			0x8
+#define QPNP_REG_STATUS1_VAL_MASK		0x1
+#define QPNP_REG_STATUS1_GPIO_EN_REV0_MASK	0x2
+#define QPNP_REG_STATUS1_GPIO_EN_MASK		0x80
+#define QPNP_REG_STATUS1_MPP_EN_MASK		0x80
+
+/* control register base address offsets */
+#define QPNP_REG_MODE_CTL			0x40
+#define QPNP_REG_DIG_VIN_CTL			0x41
+#define QPNP_REG_DIG_PULL_CTL			0x42
+#define QPNP_REG_DIG_IN_CTL			0x43
+#define QPNP_REG_DIG_OUT_CTL			0x45
+#define QPNP_REG_EN_CTL				0x46
+#define QPNP_REG_AOUT_CTL			0x4b
+#define QPNP_REG_AIN_CTL			0x4a
+#define QPNP_REG_SINK_CTL			0x4c
+
+/* QPNP_REG_MODE_CTL */
+#define QPNP_REG_MODE_INVERT_SHIFT		0
+#define QPNP_REG_MODE_INVERT_MASK		0x1
+#define QPNP_REG_MODE_FUNCTION_SHIFT		1
+#define QPNP_REG_MODE_FUNCTION_MASK		0x6
+#define QPNP_REG_MODE_SEL_SHIFT			4
+#define QPNP_REG_MODE_SEL_MASK			0x70
+
+/* QPNP_REG_DIG_VIN_CTL */
+#define QPNP_REG_VIN_SHIFT			0
+#define QPNP_REG_VIN_MASK			0x7
+
+/* QPNP_REG_DIG_PULL_CTL */
+#define QPNP_REG_PULL_SHIFT			0
+#define QPNP_REG_PULL_MASK			0x7
+
+/* QPNP_REG_DIG_OUT_CTL */
+#define QPNP_REG_OUT_STRENGTH_SHIFT		0
+#define QPNP_REG_OUT_STRENGTH_MASK		0x3
+#define QPNP_REG_OUT_TYPE_SHIFT			4
+#define QPNP_REG_OUT_TYPE_MASK			0x30
+
+/* QPNP_REG_EN_CTL */
+#define QPNP_REG_MASTER_EN_SHIFT		7
+#define QPNP_REG_MASTER_EN_MASK			0x80
+
+/* QPNP_REG_AOUT_CTL */
+#define QPNP_REG_AOUT_REF_SHIFT			0
+#define QPNP_REG_AOUT_REF_MASK			0x7
+
+/* QPNP_REG_AIN_CTL */
+#define QPNP_REG_AIN_ROUTE_SHIFT		0
+#define QPNP_REG_AIN_ROUTE_MASK			0x7
+
+/* QPNP_REG_SINK_CTL */
+#define QPNP_REG_CS_OUT_SHIFT			0
+#define QPNP_REG_CS_OUT_MASK			0x7
+
+#define QPNP_PIN_PHYSICAL_OFFSET		1
+
+/* Qualcomm specific pin configurations */
+#define QPNP_PINCONF_PULL_UP			(PIN_CONFIG_END + 1)
+#define QPNP_PINCONF_STRENGTH			(PIN_CONFIG_END + 2)
+#define QPNP_PINCONF_AMUX_ROUTE			(PIN_CONFIG_END + 3)
+#define QPNP_PINCONF_VREFENCE			(PIN_CONFIG_END + 4)
+#define QPNP_PINCONF_MODE			(PIN_CONFIG_END + 5)
+
+struct qpnp_chipinfo {
+	unsigned npins;
+	unsigned base;
+	unsigned type;
+};
+
+struct qpnp_padinfo {
+	u16 offset;		/* address offset in SPMI device */
+	int irq;
+	const char *name;	/* pin name */
+	unsigned int modes;	/* supported modes: DI, DO, DIO, AI, AO... */
+	unsigned int type;	/* peripheral hardware type */
+	unsigned int subtype;	/* peripheral hardware subtype */
+	unsigned int major;	/* digital major version */
+};
+
+#define QPNP_REG_ADDR(pad, reg) ((pad)->offset + reg)
+#define QPNP_GET(buff, shift, mask) ((buff & mask) >> shift)
+
+struct qpnp_pinctrl {
+	struct device *dev;
+	struct regmap *map;
+	struct pinctrl_dev *ctrl;
+	struct pinctrl_desc desc;
+	struct gpio_chip chip;
+
+	struct qpnp_padinfo *pads;
+	const struct qpnp_chipinfo *info;
+	const char *const *groups;
+	const char *const *functions;
+};
+
+static inline struct qpnp_pinctrl *to_qpnp_pinctrl(struct gpio_chip *chip)
+{
+	return container_of(chip, struct qpnp_pinctrl, chip);
+};
+
+struct qpnp_pinbindings {
+	const char *property;
+	unsigned param;
+	u32 default_value;
+};
+
+struct qpnp_pinattrib {
+	unsigned addr;
+	unsigned shift;
+	unsigned mask;
+	unsigned val;
+};
+
+static struct qpnp_pinbindings qpnp_pinbindings[] = {
+	/* QCOM_BIAS_PULL_UP_30...  */
+	{"qcom,pull-up-strength", QPNP_PINCONF_PULL_UP, 0},
+	/* QCOM_DRIVE_STRENGTH_NO... */
+	{"qcom,drive-strength",	QPNP_PINCONF_STRENGTH, 0},
+	/* PMIC_MPP_AMUX_ROUTE_CH5 ... */
+	{"qcom,amux-route",	QPNP_PINCONF_AMUX_ROUTE, 0},
+	/* PMIC_MPP_VREFERENCE_1V25 ... */
+	{"qcom,vrefence",	QPNP_PINCONF_VREFENCE, 0},
+	/* PMIC_MPP_MODE.. */
+	{"qcom,mode",	        QPNP_PINCONF_MODE, 0},
+};
+
+static const char * const qpnp_gpio_groups[] = {
+	"gpio1", "gpio2", "gpio3", "gpio4", "gpio5", "gpio6", "gpio7", "gpio8",
+	"gpio9", "gpio10", "gpio11", "gpio12", "gpio13", "gpio14", "gpio15",
+	"gpio16", "gpio17", "gpio18", "gpio19", "gpio20", "gpio21", "gpio22",
+	"gpio23", "gpio24", "gpio25", "gpio26", "gpio27", "gpio28", "gpio29",
+	"gpio30", "gpio31", "gpio32", "gpio33", "gpio34", "gpio35", "gpio36",
+};
+
+static const char * const qpnp_mpp_groups[] = {
+	"mpp1", "mpp2", "mpp3", "mpp4", "mpp5", "mpp6", "mpp7", "mpp8",
+};
+
+static const char * const qpnp_gpio_functions[] = {
+	PMIC_GPIO_FUNC_NORMAL, PMIC_GPIO_FUNC_PAIRED,
+	PMIC_GPIO_FUNC_FUNC1, PMIC_GPIO_FUNC_FUNC2,
+	PMIC_GPIO_FUNC_DTEST1, PMIC_GPIO_FUNC_DTEST2,
+	PMIC_GPIO_FUNC_DTEST3, PMIC_GPIO_FUNC_DTEST4,
+};
+
+static const char * const qpnp_mpp_functions[] = {
+	PMIC_MPP_FUNC_NORMAL, PMIC_MPP_FUNC_PAIRED,
+	"reserved1", "reserved2",
+	PMIC_MPP_FUNC_DTEST1, PMIC_MPP_FUNC_DTEST2,
+	PMIC_MPP_FUNC_DTEST3, PMIC_MPP_FUNC_DTEST4,
+};
+
+static inline struct qpnp_padinfo *qpnp_get_desc(struct qpnp_pinctrl *qctrl,
+						 unsigned pin)
+{
+	if (pin >= qctrl->desc.npins) {
+		dev_warn(qctrl->dev, "invalid pin number %d", pin);
+		return NULL;
+	}
+
+	return &qctrl->pads[pin];
+}
+
+static int qpnp_conv_to_pin(struct qpnp_pinctrl *qctrl,
+			   struct qpnp_padinfo *pad, unsigned param,
+			   unsigned val)
+{
+	struct qpnp_pinattrib attr[3];
+	unsigned int type, subtype;
+	int nattrs = 1, idx, ret;
+
+	type = pad->type;
+	subtype = pad->subtype;
+
+	switch (param) {
+	case PIN_CONFIG_DRIVE_PUSH_PULL:
+		if (type != QPNP_GPIO_TYPE)
+			return -ENXIO;
+		attr[0].addr  = QPNP_REG_DIG_OUT_CTL;
+		attr[0].shift = QPNP_REG_OUT_TYPE_SHIFT;
+		attr[0].mask  = QPNP_REG_OUT_TYPE_MASK;
+		attr[0].val   = QPNP_GPIO_OUT_BUF_CMOS;
+		break;
+	case PIN_CONFIG_DRIVE_OPEN_DRAIN:
+		if (type != QPNP_GPIO_TYPE)
+			return -ENXIO;
+		if (subtype == QPNP_GPIO_SUBTYPE_GPIOC_4CH ||
+		    subtype == QPNP_GPIO_SUBTYPE_GPIOC_8CH)
+			return -EINVAL;
+		attr[0].addr  = QPNP_REG_DIG_OUT_CTL;
+		attr[0].shift = QPNP_REG_OUT_TYPE_SHIFT;
+		attr[0].mask  = QPNP_REG_OUT_TYPE_MASK;
+		attr[0].val   = QPNP_GPIO_OUT_BUF_OPEN_DRAIN_NMOS;
+		break;
+	case PIN_CONFIG_DRIVE_OPEN_SOURCE:
+		if (type != QPNP_GPIO_TYPE)
+			return -ENXIO;
+		if (subtype == QPNP_GPIO_SUBTYPE_GPIOC_4CH ||
+		    subtype == QPNP_GPIO_SUBTYPE_GPIOC_8CH)
+			return -EINVAL;
+		attr[0].addr  = QPNP_REG_DIG_OUT_CTL;
+		attr[0].shift = QPNP_REG_OUT_TYPE_SHIFT;
+		attr[0].mask  = QPNP_REG_OUT_TYPE_MASK;
+		attr[0].val   = QPNP_GPIO_OUT_BUF_OPEN_DRAIN_PMOS;
+		break;
+	case PIN_CONFIG_BIAS_DISABLE:
+		attr[0].addr  = QPNP_REG_DIG_PULL_CTL;
+		attr[0].shift = QPNP_REG_PULL_SHIFT;
+		attr[0].mask  = QPNP_REG_PULL_MASK;
+		if (type == QPNP_GPIO_TYPE)
+			attr[0].val = QPNP_GPIO_PULL_NO;
+		else
+			attr[0].val = QPNP_MPP_PULL_UP_OPEN;
+		break;
+	case PIN_CONFIG_BIAS_PULL_UP:
+		if (type != QPNP_MPP_TYPE)
+			return -EINVAL;
+		switch (val) {
+		case 0:
+			val = QPNP_MPP_PULL_UP_OPEN;
+			break;
+		case 600:
+			val = QPNP_MPP_PULL_UP_0P6KOHM;
+			break;
+		case 10000:
+			val = QPNP_MPP_PULL_UP_10KOHM;
+			break;
+		case 30000:
+			val = QPNP_MPP_PULL_UP_30KOHM;
+			break;
+		default:
+			return -EINVAL;
+		}
+		attr[0].addr  = QPNP_REG_DIG_PULL_CTL;
+		attr[0].shift = QPNP_REG_PULL_SHIFT;
+		attr[0].mask  = QPNP_REG_PULL_MASK;
+		attr[0].val   = val;
+		break;
+	case PIN_CONFIG_BIAS_PULL_DOWN:
+		if (type != QPNP_GPIO_TYPE)
+			return -EINVAL;
+		attr[0].addr  = QPNP_REG_DIG_PULL_CTL;
+		attr[0].shift = QPNP_REG_PULL_SHIFT;
+		attr[0].mask  = QPNP_REG_PULL_MASK;
+		if (val)
+			attr[0].val = QPNP_GPIO_PULL_DN;
+		else
+			attr[0].val = QPNP_GPIO_PULL_NO;
+		break;
+	case PIN_CONFIG_POWER_SOURCE:
+		if (val >= QPNP_PIN_VIN_8CH_INVALID)
+			return -EINVAL;
+		if (val >= QPNP_PIN_VIN_4CH_INVALID) {
+			if (type == QPNP_GPIO_TYPE &&
+			   (subtype == QPNP_GPIO_SUBTYPE_GPIO_4CH ||
+			    subtype == QPNP_GPIO_SUBTYPE_GPIOC_4CH))
+				return -EINVAL;
+			if (type == QPNP_MPP_TYPE &&
+			   (subtype == QPNP_MPP_SUBTYPE_4CH_NO_ANA_OUT ||
+			    subtype == QPNP_MPP_SUBTYPE_4CH_NO_SINK ||
+			    subtype == QPNP_MPP_SUBTYPE_4CH_FULL_FUNC ||
+			    subtype == QPNP_MPP_SUBTYPE_ULT_4CH_NO_ANA_OUT ||
+			    subtype == QPNP_MPP_SUBTYPE_ULT_4CH_NO_SINK))
+				return -EINVAL;
+		}
+		attr[0].addr  = QPNP_REG_DIG_VIN_CTL;
+		attr[0].shift = QPNP_REG_VIN_SHIFT;
+		attr[0].mask  = QPNP_REG_VIN_MASK;
+		attr[0].val   = val;
+		break;
+	case PIN_CONFIG_DRIVE_STRENGTH:
+		if (type != QPNP_MPP_TYPE)
+			return -EINVAL;
+		if (subtype == QPNP_MPP_SUBTYPE_4CH_NO_SINK ||
+		    subtype == QPNP_MPP_SUBTYPE_ULT_4CH_NO_SINK)
+			return -ENXIO;
+		if (val > 50)	/* mA */
+			return -EINVAL;
+		attr[0].addr  = QPNP_REG_SINK_CTL;
+		attr[0].shift = QPNP_REG_CS_OUT_SHIFT;
+		attr[0].mask  = QPNP_REG_CS_OUT_MASK;
+		attr[0].val   = (val / 5) - 1;
+		break;
+	case PIN_CONFIG_INPUT_ENABLE:
+		nattrs = 2;
+		attr[0].addr  = QPNP_REG_MODE_CTL;
+		attr[0].shift = QPNP_REG_MODE_SEL_SHIFT;
+		attr[0].mask  = QPNP_REG_MODE_SEL_MASK;
+		attr[0].val   = QPNP_PIN_MODE_DIG_IN;
+		attr[1].addr  = QPNP_REG_EN_CTL;
+		attr[1].shift = QPNP_REG_MASTER_EN_SHIFT;
+		attr[1].mask  = QPNP_REG_MASTER_EN_MASK;
+		attr[1].val   = 1;
+		if (val)
+			break;
+	/* Fallthrough */
+	case PIN_CONFIG_BIAS_HIGH_IMPEDANCE:
+		attr[1].addr  = QPNP_REG_EN_CTL;
+		attr[1].shift = QPNP_REG_MASTER_EN_SHIFT;
+		attr[1].mask  = QPNP_REG_MASTER_EN_MASK;
+		attr[1].val   = 0;
+		break;
+	case PIN_CONFIG_OUTPUT:
+		nattrs = 3;
+		attr[0].addr  = QPNP_REG_MODE_CTL;
+		attr[0].shift = QPNP_REG_MODE_INVERT_SHIFT;
+		attr[0].mask  = QPNP_REG_MODE_INVERT_MASK;
+		attr[0].val   = !!val;
+		attr[1].addr  = QPNP_REG_MODE_CTL;
+		attr[1].shift = QPNP_REG_MODE_SEL_SHIFT;
+		attr[1].mask  = QPNP_REG_MODE_SEL_MASK;
+		attr[1].val   = QPNP_PIN_MODE_DIG_OUT;
+		attr[2].addr  = QPNP_REG_EN_CTL;
+		attr[2].shift = QPNP_REG_MASTER_EN_SHIFT;
+		attr[2].mask  = QPNP_REG_MASTER_EN_MASK;
+		attr[2].val   = 1;
+		break;
+	case QPNP_PINCONF_PULL_UP:
+		if (type != QPNP_GPIO_TYPE)
+			return -EINVAL;
+		switch (val) {
+		default:
+			return -EINVAL;
+		case 0:
+			val = QPNP_GPIO_PULL_NO;
+			break;
+		case PMIC_GPIO_PULL_UP_30:
+			val = QPNP_GPIO_PULL_UP_30;
+			break;
+		case PMIC_GPIO_PULL_UP_1P5:
+			val = QPNP_GPIO_PULL_UP_1P5;
+			break;
+		case PMIC_GPIO_PULL_UP_31P5:
+			val = QPNP_GPIO_PULL_UP_31P5;
+			break;
+		case PMIC_GPIO_PULL_UP_1P5_30:
+			val = QPNP_GPIO_PULL_UP_1P5_30;
+			break;
+		}
+		attr[0].addr  = QPNP_REG_DIG_PULL_CTL;
+		attr[0].shift = QPNP_REG_PULL_SHIFT;
+		attr[0].mask  = QPNP_REG_PULL_MASK;
+		attr[0].val   = val;
+		break;
+	case QPNP_PINCONF_STRENGTH:
+		if (type != QPNP_GPIO_TYPE)
+			return -EINVAL;
+		switch (val) {
+		default:
+		case PMIC_GPIO_STRENGTH_NO:
+			return -EINVAL;
+		case PMIC_GPIO_STRENGTH_LOW:
+			attr[0].val = QPNP_GPIO_STRENGTH_LOW;
+			break;
+		case PMIC_GPIO_STRENGTH_MED:
+			attr[0].val = QPNP_GPIO_STRENGTH_MED;
+			break;
+		case PMIC_GPIO_STRENGTH_HIGH:
+			attr[0].val = QPNP_GPIO_STRENGTH_HIGH;
+			break;
+		}
+		attr[0].addr  = QPNP_REG_DIG_OUT_CTL;
+		attr[0].shift = QPNP_REG_OUT_STRENGTH_SHIFT;
+		attr[0].mask  = QPNP_REG_OUT_STRENGTH_MASK;
+		break;
+	case QPNP_PINCONF_VREFENCE:
+		if (type != QPNP_MPP_TYPE)
+			return -ENXIO;
+		if (val >= QPNP_MPP_AOUT_INVALID)
+			return -EINVAL;
+		if (subtype == QPNP_MPP_SUBTYPE_4CH_NO_ANA_OUT ||
+		    subtype == QPNP_MPP_SUBTYPE_ULT_4CH_NO_ANA_OUT)
+			return -ENXIO;
+		attr[0].addr  = QPNP_REG_AOUT_CTL;
+		attr[0].shift = QPNP_REG_AOUT_REF_SHIFT;
+		attr[0].mask  = QPNP_REG_AOUT_REF_MASK;
+		attr[0].val   = val;
+		break;
+	case QPNP_PINCONF_AMUX_ROUTE:
+		if (type != QPNP_MPP_TYPE)
+			return -ENXIO;
+		if (val >= QPNP_MPP_AIN_INVALID)
+			return -EINVAL;
+		attr[0].addr  = QPNP_REG_AIN_CTL;
+		attr[0].shift = QPNP_REG_AIN_ROUTE_SHIFT;
+		attr[0].mask  = QPNP_REG_AIN_ROUTE_MASK;
+		attr[0].val   = val;
+		break;
+	case QPNP_PINCONF_MODE:
+		if ((pad->modes & BIT(val)) == 0)
+			return -ENXIO;
+		attr[0].addr  = QPNP_REG_MODE_CTL;
+		attr[0].shift = QPNP_REG_MODE_SEL_SHIFT;
+		attr[0].mask  = QPNP_REG_MODE_SEL_MASK;
+		attr[0].val   = val;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	for (idx = 0; idx < nattrs; idx++) {
+		/* add base offset */
+		attr[idx].addr = QPNP_REG_ADDR(pad, attr[idx].addr);
+		ret = regmap_update_bits(qctrl->map, attr[idx].addr,
+					 attr[idx].mask,
+					 attr[idx].val << attr[idx].shift);
+		if (ret < 0)
+			return ret;
+	}
+
+	return 0;
+}
+
+
+static int qpnp_conv_from_pin(struct qpnp_pinctrl *qctrl,
+			     struct qpnp_padinfo *pad,
+			     unsigned param, unsigned *val)
+{
+	struct qpnp_pinattrib attr;
+	unsigned int type, subtype, field;
+	unsigned int addr, buff;
+	int ret;
+
+	*val = 0;
+	type = pad->type;
+	subtype = pad->subtype;
+
+	switch (param) {
+	case PIN_CONFIG_DRIVE_PUSH_PULL:
+	case PIN_CONFIG_DRIVE_OPEN_DRAIN:
+	case PIN_CONFIG_DRIVE_OPEN_SOURCE:
+		if (type != QPNP_GPIO_TYPE)
+			return -ENXIO;
+		attr.addr  = QPNP_REG_DIG_OUT_CTL;
+		attr.shift = QPNP_REG_OUT_TYPE_SHIFT;
+		attr.mask  = QPNP_REG_OUT_TYPE_MASK;
+		break;
+	case PIN_CONFIG_BIAS_PULL_DOWN:
+		if (type != QPNP_GPIO_TYPE)
+			return -ENXIO;
+	/* Fallthrough */
+	case PIN_CONFIG_BIAS_DISABLE:
+	case PIN_CONFIG_BIAS_PULL_UP:
+		attr.addr  = QPNP_REG_DIG_PULL_CTL;
+		attr.shift = QPNP_REG_PULL_SHIFT;
+		attr.mask  = QPNP_REG_PULL_MASK;
+		break;
+	case PIN_CONFIG_BIAS_HIGH_IMPEDANCE:
+		attr.addr  = QPNP_REG_EN_CTL;
+		attr.shift = QPNP_REG_MASTER_EN_SHIFT;
+		attr.mask  = QPNP_REG_MASTER_EN_MASK;
+		break;
+	case PIN_CONFIG_POWER_SOURCE:
+		attr.addr  = QPNP_REG_DIG_VIN_CTL;
+		attr.shift = QPNP_REG_VIN_SHIFT;
+		attr.mask  = QPNP_REG_VIN_MASK;
+		break;
+	case PIN_CONFIG_DRIVE_STRENGTH:
+		if (type != QPNP_MPP_TYPE)
+			return -ENXIO;
+		attr.addr  = QPNP_REG_SINK_CTL;
+		attr.shift = QPNP_REG_CS_OUT_SHIFT;
+		attr.mask  = QPNP_REG_CS_OUT_MASK;
+		break;
+	case PIN_CONFIG_INPUT_ENABLE:
+		attr.addr  = QPNP_REG_EN_CTL;
+		attr.shift = QPNP_REG_MASTER_EN_SHIFT;
+		attr.mask  = QPNP_REG_MASTER_EN_MASK;
+		break;
+	case PIN_CONFIG_OUTPUT:
+		attr.addr  = QPNP_REG_MODE_CTL;
+		attr.shift = QPNP_REG_MODE_INVERT_SHIFT;
+		attr.mask  = QPNP_REG_MODE_INVERT_MASK;
+		break;
+	case QPNP_PINCONF_PULL_UP:
+		if (type != QPNP_GPIO_TYPE)
+			return -ENXIO;
+		attr.addr  = QPNP_REG_DIG_PULL_CTL;
+		attr.shift = QPNP_REG_PULL_SHIFT;
+		attr.mask  = QPNP_REG_PULL_MASK;
+		break;
+	case QPNP_PINCONF_STRENGTH:
+		if (type != QPNP_GPIO_TYPE)
+			return -ENXIO;
+		attr.addr  = QPNP_REG_DIG_OUT_CTL;
+		attr.shift = QPNP_REG_OUT_STRENGTH_SHIFT;
+		attr.mask  = QPNP_REG_OUT_STRENGTH_MASK;
+		break;
+	case QPNP_PINCONF_VREFENCE:
+		if (type != QPNP_MPP_TYPE)
+			return -ENXIO;
+		if (subtype == QPNP_MPP_SUBTYPE_4CH_NO_ANA_OUT ||
+		    subtype == QPNP_MPP_SUBTYPE_ULT_4CH_NO_ANA_OUT)
+			return -ENXIO;
+		attr.addr  = QPNP_REG_AOUT_CTL;
+		attr.shift = QPNP_REG_AOUT_REF_SHIFT;
+		attr.mask  = QPNP_REG_AOUT_REF_MASK;
+		break;
+	case QPNP_PINCONF_AMUX_ROUTE:
+		if (type != QPNP_MPP_TYPE)
+			return -ENXIO;
+		attr.addr  = QPNP_REG_AIN_CTL;
+		attr.shift = QPNP_REG_AIN_ROUTE_SHIFT;
+		attr.mask  = QPNP_REG_AIN_ROUTE_MASK;
+		break;
+	case QPNP_PINCONF_MODE:
+		attr.addr  = QPNP_REG_MODE_CTL;
+		attr.shift = QPNP_REG_MODE_SEL_SHIFT;
+		attr.mask  = QPNP_REG_MODE_SEL_MASK;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	addr = QPNP_REG_ADDR(pad, attr.addr);
+	ret = regmap_read(qctrl->map, addr, &buff);
+	if (ret < 0)
+		return ret;
+
+	field = QPNP_GET(buff, attr.shift, attr.mask);
+
+	switch (param) {
+	case PIN_CONFIG_DRIVE_PUSH_PULL:
+		if (field == QPNP_GPIO_OUT_BUF_CMOS)
+			*val = 1;
+		break;
+	case PIN_CONFIG_DRIVE_OPEN_DRAIN:
+		if (field == QPNP_GPIO_OUT_BUF_OPEN_DRAIN_NMOS)
+			*val = 1;
+		break;
+	case PIN_CONFIG_DRIVE_OPEN_SOURCE:
+		if (field == QPNP_GPIO_OUT_BUF_OPEN_DRAIN_PMOS)
+			*val = 1;
+		break;
+	case PIN_CONFIG_BIAS_DISABLE:
+		if (type == QPNP_GPIO_TYPE) {
+			if (field == QPNP_GPIO_PULL_NO)
+				*val = 1;
+		} else {
+			if (field == QPNP_MPP_PULL_UP_OPEN)
+				*val = 1;
+		}
+		break;
+	case PIN_CONFIG_BIAS_PULL_UP:
+		switch (field) {
+		default:
+		case QPNP_MPP_PULL_UP_OPEN:
+			*val = 0;
+			break;
+		case QPNP_MPP_PULL_UP_0P6KOHM:
+			*val = 600;
+			break;
+		case QPNP_MPP_PULL_UP_10KOHM:
+			*val = 10000;
+			break;
+		case QPNP_MPP_PULL_UP_30KOHM:
+			*val = 30000;
+			break;
+		}
+		break;
+	case PIN_CONFIG_BIAS_PULL_DOWN:
+		if (field == QPNP_GPIO_PULL_DN)
+			*val = 1;
+		break;
+	case PIN_CONFIG_POWER_SOURCE:
+		*val = field;
+		break;
+	case PIN_CONFIG_DRIVE_STRENGTH:
+		*val = (field + 1) * 5;
+		break;
+	case PIN_CONFIG_INPUT_ENABLE:
+		*val = field;
+		break;
+	case PIN_CONFIG_BIAS_HIGH_IMPEDANCE:
+		if (field == QPNP_PIN_MASTER_DISABLE)
+			*val = 1;
+		break;
+	case PIN_CONFIG_OUTPUT:
+		*val = field;
+		break;
+	case QPNP_PINCONF_PULL_UP:
+		switch (field) {
+		case QPNP_GPIO_PULL_NO:
+			field = 0;
+			break;
+		case QPNP_GPIO_PULL_UP_30:
+			field = PMIC_GPIO_PULL_UP_30;
+			break;
+		case QPNP_GPIO_PULL_UP_1P5:
+			field = PMIC_GPIO_PULL_UP_1P5;
+			break;
+		case QPNP_GPIO_PULL_UP_31P5:
+			field = PMIC_GPIO_PULL_UP_31P5;
+			break;
+
+		case QPNP_GPIO_PULL_UP_1P5_30:
+			field = PMIC_GPIO_PULL_UP_1P5_30;
+			break;
+		}
+		*val = field;
+		break;
+	case QPNP_PINCONF_STRENGTH:
+		switch (field) {
+		case QPNP_GPIO_STRENGTH_HIGH:
+			field = PMIC_GPIO_STRENGTH_HIGH;
+			break;
+		case QPNP_GPIO_STRENGTH_MED:
+			field = PMIC_GPIO_STRENGTH_MED;
+			break;
+		case QPNP_GPIO_STRENGTH_LOW:
+			field = PMIC_GPIO_STRENGTH_LOW;
+			break;
+		}
+		*val = field;
+		break;
+	case QPNP_PINCONF_MODE:
+	case QPNP_PINCONF_VREFENCE:
+	case QPNP_PINCONF_AMUX_ROUTE:
+		*val = field;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int qpnp_get_groups_count(struct pinctrl_dev *pctldev)
+{
+	struct qpnp_pinctrl *qpctrl = pinctrl_dev_get_drvdata(pctldev);
+
+	/* Every PIN is a group */
+	return qpctrl->desc.npins;
+}
+
+static const char *qpnp_get_group_name(struct pinctrl_dev *pctldev,
+				       unsigned pin)
+{
+	struct qpnp_pinctrl *qpctrl = pinctrl_dev_get_drvdata(pctldev);
+
+	/* Every PIN is a group */
+	return qpctrl->desc.pins[pin].name;
+}
+
+static int qpnp_get_group_pins(struct pinctrl_dev *pctldev,
+			      unsigned pin,
+			      const unsigned **pins,
+			      unsigned *num_pins)
+{
+	struct qpnp_pinctrl *qpctrl = pinctrl_dev_get_drvdata(pctldev);
+
+	/* Every PIN is a group */
+	*pins = &qpctrl->desc.pins[pin].number;
+	*num_pins = 1;
+	return 0;
+}
+
+static int qpnp_parse_dt_config(struct device_node *np,
+			      struct pinctrl_dev *pctldev,
+			      unsigned long **configs, unsigned int *nconfs)
+{
+	struct qpnp_pinbindings *par;
+	unsigned long cfg;
+	int ret, idx;
+	u32 val;
+
+	for (idx = 0; idx < ARRAY_SIZE(qpnp_pinbindings); idx++) {
+
+		par = &qpnp_pinbindings[idx];
+		ret = of_property_read_u32(np, par->property, &val);
+
+		/* property not found */
+		if (ret == -EINVAL)
+			continue;
+
+		/* use default value, when no value is specified */
+		if (ret)
+			val = par->default_value;
+
+		dev_dbg(pctldev->dev, "found %s with value %u\n",
+			par->property, val);
+
+		cfg = pinconf_to_config_packed(par->param, val);
+
+		ret = pinctrl_utils_add_config(pctldev, configs, nconfs, cfg);
+		if (ret)
+			return ret;
+	}
+
+	return 0;
+}
+
+static int qpnp_dt_subnode_to_map(struct pinctrl_dev *pctldev,
+				  struct device_node *np,
+				  struct pinctrl_map **map,
+				  unsigned *reserv, unsigned *nmaps,
+				  enum pinctrl_map_type type)
+{
+	unsigned long *configs = NULL;
+	unsigned nconfs = 0;
+	struct property *prop;
+	const char *group;
+	int ret;
+
+	ret = qpnp_parse_dt_config(np, pctldev, &configs, &nconfs);
+	if (ret < 0)
+		return ret;
+
+	if (!nconfs)
+		return 0;
+
+	ret = of_property_count_strings(np, "pins");
+	if (ret < 0)
+		goto exit;
+
+	ret = pinctrl_utils_reserve_map(pctldev, map, reserv,
+					nmaps, ret);
+	if (ret < 0)
+		goto exit;
+
+	of_property_for_each_string(np, "pins", prop, group) {
+		ret = pinctrl_utils_add_map_configs(pctldev, map,
+				reserv, nmaps, group, configs, nconfs, type);
+		if (ret < 0)
+			break;
+	}
+exit:
+	kfree(configs);
+	return ret;
+}
+
+static int qpnp_dt_node_to_map(struct pinctrl_dev *pctldev,
+			       struct device_node *np_config,
+			       struct pinctrl_map **map,
+			       unsigned *nmaps)
+{
+	struct device_node *np;
+	enum pinctrl_map_type type;
+	unsigned reserv;
+	int ret;
+
+	ret = 0;
+	*map = NULL;
+	*nmaps = 0;
+	reserv = 0;
+	type = PIN_MAP_TYPE_CONFIGS_GROUP;
+
+	for_each_child_of_node(np_config, np) {
+
+		ret = pinconf_generic_dt_subnode_to_map(pctldev, np, map,
+							&reserv, nmaps, type);
+		if (ret)
+			break;
+
+		ret = qpnp_dt_subnode_to_map(pctldev, np, map, &reserv,
+					     nmaps, type);
+		if (ret)
+			break;
+	}
+
+	if (ret < 0)
+		pinctrl_utils_dt_free_map(pctldev, *map, *nmaps);
+
+	return ret;
+}
+
+static const struct pinctrl_ops qpnp_pinctrl_ops = {
+	.get_groups_count	= qpnp_get_groups_count,
+	.get_group_name		= qpnp_get_group_name,
+	.get_group_pins		= qpnp_get_group_pins,
+	.dt_node_to_map		= qpnp_dt_node_to_map,
+	.dt_free_map		= pinctrl_utils_dt_free_map,
+};
+
+static int qpnp_get_functions_count(struct pinctrl_dev *pctldev)
+{
+	return ARRAY_SIZE(qpnp_gpio_functions);
+}
+
+static const char *qpnp_get_function_name(struct pinctrl_dev *pctldev,
+					 unsigned function)
+{
+	struct qpnp_pinctrl *qctrl = pinctrl_dev_get_drvdata(pctldev);
+
+	return qctrl->functions[function];
+}
+
+static int qpnp_get_function_groups(struct pinctrl_dev *pctldev,
+				  unsigned function,
+				  const char *const **groups,
+				  unsigned *const num_qgroups)
+{
+	struct qpnp_pinctrl *qctrl = pinctrl_dev_get_drvdata(pctldev);
+
+	*groups = qctrl->groups;
+	*num_qgroups = qctrl->desc.npins;
+	return 0;
+}
+
+static int qpnp_pinmux_enable(struct pinctrl_dev *pctldev,
+			     unsigned function,
+			     unsigned pin)
+{
+	struct qpnp_pinctrl *qctrl = pinctrl_dev_get_drvdata(pctldev);
+	struct qpnp_padinfo *pad;
+	unsigned int addr, val, mask;
+	int ret;
+
+	pad = qpnp_get_desc(qctrl, pin);
+	if (!pad)
+		return -EINVAL;
+
+	addr = QPNP_REG_ADDR(pad, QPNP_REG_MODE_CTL);
+	val = function << QPNP_REG_MODE_FUNCTION_SHIFT;
+	mask = QPNP_REG_MODE_FUNCTION_MASK;
+	ret = regmap_update_bits(qctrl->map, addr, mask, val);
+	if (ret)
+		return ret;
+
+	addr = QPNP_REG_ADDR(pad, QPNP_REG_EN_CTL);
+	val = BIT(QPNP_REG_MASTER_EN_SHIFT);
+	mask = QPNP_REG_MASTER_EN_MASK;
+	ret = regmap_update_bits(qctrl->map, addr, mask, val);
+
+	return ret;
+}
+
+static const struct pinmux_ops qpnp_pinmux_ops = {
+	.get_functions_count	= qpnp_get_functions_count,
+	.get_function_name	= qpnp_get_function_name,
+	.get_function_groups	= qpnp_get_function_groups,
+	.enable			= qpnp_pinmux_enable,
+};
+
+static int qpnp_get(struct gpio_chip *chip, unsigned offset)
+{
+	struct qpnp_pinctrl *qctrl = to_qpnp_pinctrl(chip);
+	struct qpnp_padinfo *pad;
+	unsigned int val, en_mask, buff, addr;
+	int ret;
+
+	pad = qpnp_get_desc(qctrl, offset);
+	if (!pad)
+		return -EINVAL;
+
+	addr = QPNP_REG_ADDR(pad, QPNP_REG_MODE_CTL);
+	ret = regmap_read(qctrl->map, addr, &buff);
+	if (ret < 0)
+		return ret;
+
+	/* GPIO val is from RT status if input is enabled */
+	if ((buff & QPNP_REG_MODE_SEL_MASK) ==
+	    (QPNP_PIN_MODE_DIG_IN << QPNP_REG_MODE_SEL_SHIFT)) {
+
+		addr = QPNP_REG_ADDR(pad, QPNP_REG_STATUS1);
+		ret = regmap_read(qctrl->map, addr, &val);
+		if (ret < 0)
+			return ret;
+
+		if (pad->type == QPNP_GPIO_TYPE && pad->major == 0)
+			en_mask = QPNP_REG_STATUS1_GPIO_EN_REV0_MASK;
+		else if (pad->type == QPNP_GPIO_TYPE &&
+			 pad->major > 0)
+			en_mask = QPNP_REG_STATUS1_GPIO_EN_MASK;
+		else		/* MPP */
+			en_mask = QPNP_REG_STATUS1_MPP_EN_MASK;
+
+		if (!(val & en_mask))
+			return -EPERM;
+
+		ret = val & QPNP_REG_STATUS1_VAL_MASK;
+
+	} else {
+		ret = buff & QPNP_REG_MODE_INVERT_MASK;
+		ret = ret >> QPNP_REG_MODE_INVERT_SHIFT;
+	}
+
+	return !!ret;
+}
+
+static void qpnp_set(struct gpio_chip *chip, unsigned offset, int value)
+{
+	struct qpnp_pinctrl *qctrl = to_qpnp_pinctrl(chip);
+	struct qpnp_padinfo *pad;
+	unsigned int addr, buff;
+
+	pad = qpnp_get_desc(qctrl, offset);
+	if (!pad)
+		return;
+
+	addr = QPNP_REG_ADDR(pad, QPNP_REG_MODE_CTL);
+	buff = !!value << QPNP_REG_MODE_INVERT_SHIFT;
+
+	regmap_update_bits(qctrl->map, addr, QPNP_REG_MODE_INVERT_MASK, buff);
+}
+
+static int qpnp_config_get(struct pinctrl_dev *pctldev,
+			  unsigned int pin,
+			  unsigned long *config)
+{
+	struct qpnp_pinctrl *qctrl = pinctrl_dev_get_drvdata(pctldev);
+	unsigned param = pinconf_to_config_param(*config);
+	struct qpnp_padinfo *pad;
+	unsigned arg;
+	int ret;
+
+	pad = qpnp_get_desc(qctrl, pin);
+	if (!pad)
+		return -EINVAL;
+
+	/* Convert pinconf values to register values */
+	ret = qpnp_conv_from_pin(qctrl, pad, param, &arg);
+	if (ret)
+		return ret;
+
+	/* Convert register value to pinconf value */
+	*config = pinconf_to_config_packed(param, arg);
+	return 0;
+}
+
+static int qpnp_config_set(struct pinctrl_dev *pctldev, unsigned int pin,
+			  unsigned long *configs, unsigned nconfs)
+{
+	struct qpnp_pinctrl *qctrl = pinctrl_dev_get_drvdata(pctldev);
+	struct qpnp_padinfo *pad;
+	unsigned param;
+	unsigned arg;
+	int idx, ret;
+
+	pad = qpnp_get_desc(qctrl, pin);
+	if (!pad)
+		return -EINVAL;
+
+	for (idx = 0; idx < nconfs; idx++) {
+		param = pinconf_to_config_param(configs[idx]);
+		arg = pinconf_to_config_argument(configs[idx]);
+
+		/* Convert pinconf values to register values */
+		ret = qpnp_conv_to_pin(qctrl, pad, param, arg);
+		if (ret < 0) {
+			dev_err(pctldev->dev, "config %u = %u failed\n",
+				param, arg);
+			return ret;
+		}
+	}
+
+	return 0;
+}
+
+static void qpnp_config_dbg_show(struct pinctrl_dev *pctldev,
+				 struct seq_file *seq, unsigned pin)
+{
+	struct qpnp_pinctrl *qctrl = pinctrl_dev_get_drvdata(pctldev);
+	unsigned int en, buff, pull, out, drive, addr, mode, func, inv;
+	struct qpnp_padinfo *pad;
+	const char *name;
+	int ret;
+
+	static const char *const modes[] = {
+		"di", "do", "dio", "ai", "ao", "aio", "cs"
+	};
+	static const char * const biases[] = {
+		"pull-up 30uA", "pull-up 1.5uA", "pull-up 31.5uA",
+		"pull-up 1.5uA + 30uA boost", "pull-down 10uA", "no pull"
+	};
+	static const char * const buffer_types[] = {
+		"push-pull", "open-drain", "open-func"
+	};
+	static const char * const strengths[] = {
+		"no", "low", "medium", "high"
+	};
+
+	pad = qpnp_get_desc(qctrl, pin);
+	if (!pad)
+		return;
+
+	name = pad->name;
+
+	addr = QPNP_REG_ADDR(pad, QPNP_REG_MODE_CTL);
+	ret = regmap_read(qctrl->map, addr, &buff);
+	if (ret < 0) {
+		seq_printf(seq, " %-8s: read error %d", name, ret);
+		return;
+	}
+
+	mode = QPNP_GET(buff, QPNP_REG_MODE_SEL_SHIFT,
+			QPNP_REG_MODE_SEL_MASK);
+	func = QPNP_GET(buff, QPNP_REG_MODE_FUNCTION_SHIFT,
+			QPNP_REG_MODE_FUNCTION_MASK);
+	inv  = QPNP_GET(buff, QPNP_REG_MODE_INVERT_SHIFT,
+			QPNP_REG_MODE_INVERT_MASK);
+
+	addr = QPNP_REG_ADDR(pad, QPNP_REG_DIG_PULL_CTL);
+	ret = regmap_read(qctrl->map, addr, &buff);
+	if (ret < 0) {
+		seq_printf(seq, " %-8s: read error %d", name, ret);
+		return;
+	}
+	pull = QPNP_GET(buff, QPNP_REG_PULL_SHIFT, QPNP_REG_PULL_MASK);
+
+	addr = QPNP_REG_ADDR(pad, QPNP_REG_DIG_OUT_CTL);
+	ret = regmap_read(qctrl->map, addr, &buff);
+	if (ret < 0) {
+		seq_printf(seq, " %-8s: read error %d", name, ret);
+		return;
+	}
+	out = QPNP_GET(buff, QPNP_REG_OUT_TYPE_SHIFT, QPNP_REG_OUT_TYPE_MASK);
+	drive = QPNP_GET(buff, QPNP_REG_OUT_STRENGTH_SHIFT,
+			 QPNP_REG_OUT_STRENGTH_MASK);
+
+	addr = QPNP_REG_ADDR(pad, QPNP_REG_EN_CTL);
+	ret = regmap_read(qctrl->map, addr, &buff);
+	if (ret < 0) {
+		seq_printf(seq, " %-8s: read error %d", name, ret);
+		return;
+	}
+	en = QPNP_GET(buff, QPNP_REG_MASTER_EN_SHIFT, QPNP_REG_MASTER_EN_MASK);
+
+	seq_printf(seq, " %-8s: %-4s", name, modes[mode]);
+	seq_printf(seq, " %-7s", qctrl->functions[func]);
+	seq_printf(seq, " %-24s %-12s", biases[pull], buffer_types[out]);
+	seq_printf(seq, " %-6s %-4s", strengths[drive], inv ? "inv" : "");
+	seq_printf(seq, " %s", !en ? "high-Z" : "");
+
+}
+
+static const struct pinconf_ops qpnp_pinconf_ops = {
+	.pin_config_group_get	= qpnp_config_get,
+	.pin_config_group_set	= qpnp_config_set,
+	.pin_config_group_dbg_show = qpnp_config_dbg_show,
+};
+
+static int qpnp_direction_input(struct gpio_chip *chip, unsigned offset)
+{
+	struct qpnp_pinctrl *qctrl = to_qpnp_pinctrl(chip);
+	unsigned long config;
+
+	config = pinconf_to_config_packed(PIN_CONFIG_INPUT_ENABLE, 1);
+
+	return qpnp_config_set(qctrl->ctrl, offset, &config, 1);
+}
+
+static int qpnp_direction_output(struct gpio_chip *chip,
+			      unsigned offset, int val)
+{
+	struct qpnp_pinctrl *qctrl = to_qpnp_pinctrl(chip);
+	unsigned long config;
+
+	config = pinconf_to_config_packed(PIN_CONFIG_OUTPUT, val);
+	return qpnp_config_set(qctrl->ctrl, offset, &config, 1);
+}
+
+static int qpnp_request(struct gpio_chip *chip, unsigned offset)
+{
+	return pinctrl_request_gpio(chip->base + offset);
+}
+
+static void qpnp_free(struct gpio_chip *chip, unsigned offset)
+{
+	pinctrl_free_gpio(chip->base + offset);
+}
+
+static int qpnp_of_xlate(struct gpio_chip *chip,
+		       const struct of_phandle_args *gpio_desc, u32 *flags)
+{
+	struct qpnp_pinctrl *qctrl = to_qpnp_pinctrl(chip);
+	struct qpnp_padinfo *pad;
+	unsigned pin = gpio_desc->args[0] - QPNP_PIN_PHYSICAL_OFFSET;
+
+	if (chip->of_gpio_n_cells < 2)
+		return -EINVAL;
+
+	pad = qpnp_get_desc(qctrl, pin);
+	if (!pad)
+		return -EINVAL;
+
+	if (flags)
+		*flags = gpio_desc->args[1];
+
+	return pin;
+}
+
+static int qpnp_to_irq(struct gpio_chip *chip, unsigned offset)
+{
+	struct qpnp_pinctrl *qctrl = to_qpnp_pinctrl(chip);
+	struct qpnp_padinfo *pad;
+
+	pad = qpnp_get_desc(qctrl, offset);
+	if (!pad)
+		return -EINVAL;
+
+	return pad->irq;
+}
+
+static void qpnp_dbg_show(struct seq_file *s, struct gpio_chip *chip)
+{
+	struct qpnp_pinctrl *qctrl = to_qpnp_pinctrl(chip);
+	unsigned idx;
+
+	for (idx = 0; idx < chip->ngpio; idx++) {
+		qpnp_config_dbg_show(qctrl->ctrl, s, idx);
+		seq_puts(s, "\n");
+	}
+}
+
+static const struct gpio_chip qpnp_gpio_template = {
+	.direction_input  = qpnp_direction_input,
+	.direction_output = qpnp_direction_output,
+	.get              = qpnp_get,
+	.set              = qpnp_set,
+	.request          = qpnp_request,
+	.free             = qpnp_free,
+	.of_xlate	  = qpnp_of_xlate,
+	.to_irq		  = qpnp_to_irq,
+	.dbg_show         = qpnp_dbg_show,
+};
+
+static int qpnp_control_init(struct qpnp_pinctrl *qctrl,
+			  struct qpnp_padinfo *pad)
+{
+	pad->modes = 0;
+
+	if (pad->type == QPNP_GPIO_TYPE) {
+		switch (pad->subtype) {
+		case QPNP_GPIO_SUBTYPE_GPIO_4CH:
+		case QPNP_GPIO_SUBTYPE_GPIOC_4CH:
+		case QPNP_GPIO_SUBTYPE_GPIO_8CH:
+		case QPNP_GPIO_SUBTYPE_GPIOC_8CH:
+
+			/* only GPIO is supported*/
+			pad->modes |= BIT(QPNP_PIN_MODE_DIG_IN);
+			pad->modes |= BIT(QPNP_PIN_MODE_DIG_OUT);
+			pad->modes |= BIT(QPNP_PIN_MODE_DIG_IN_OUT);
+			break;
+		default:
+			dev_err(qctrl->dev, "invalid GPIO subtype 0x%x\n",
+				pad->subtype);
+			return -EINVAL;
+		}
+
+	} else if (pad->type == QPNP_MPP_TYPE) {
+
+		switch (pad->subtype) {
+		case QPNP_MPP_SUBTYPE_4CH_NO_SINK:
+		case QPNP_MPP_SUBTYPE_ULT_4CH_NO_SINK:
+
+			/* Current sink not supported*/
+			pad->modes |= BIT(QPNP_PIN_MODE_DIG_IN);
+			pad->modes |= BIT(QPNP_PIN_MODE_DIG_OUT);
+			pad->modes |= BIT(QPNP_PIN_MODE_DIG_IN_OUT);
+			pad->modes |= BIT(QPNP_PIN_MODE_BIDIR);
+			pad->modes |= BIT(QPNP_PIN_MODE_AIN);
+			pad->modes |= BIT(QPNP_PIN_MODE_AOUT);
+			break;
+		case QPNP_MPP_SUBTYPE_4CH_NO_ANA_OUT:
+		case QPNP_MPP_SUBTYPE_ULT_4CH_NO_ANA_OUT:
+
+			/* Analog output not supported */
+			pad->modes |= BIT(QPNP_PIN_MODE_DIG_IN);
+			pad->modes |= BIT(QPNP_PIN_MODE_DIG_OUT);
+			pad->modes |= BIT(QPNP_PIN_MODE_DIG_IN_OUT);
+			pad->modes |= BIT(QPNP_PIN_MODE_BIDIR);
+			pad->modes |= BIT(QPNP_PIN_MODE_AIN);
+			pad->modes |= BIT(QPNP_PIN_MODE_SINK);
+			break;
+		case QPNP_MPP_SUBTYPE_4CH_FULL_FUNC:
+		case QPNP_MPP_SUBTYPE_8CH_FULL_FUNC:
+
+			pad->modes |= BIT(QPNP_PIN_MODE_DIG_IN);
+			pad->modes |= BIT(QPNP_PIN_MODE_DIG_OUT);
+			pad->modes |= BIT(QPNP_PIN_MODE_DIG_IN_OUT);
+			pad->modes |= BIT(QPNP_PIN_MODE_BIDIR);
+			pad->modes |= BIT(QPNP_PIN_MODE_AIN);
+			pad->modes |= BIT(QPNP_PIN_MODE_AOUT);
+			pad->modes |= BIT(QPNP_PIN_MODE_SINK);
+			break;
+		default:
+			dev_err(qctrl->dev, "invalid MPP subtype 0x%x\n",
+				pad->subtype);
+			return -EINVAL;
+		}
+	} else {
+		dev_err(qctrl->dev, "invalid type 0x%x\n", pad->type);
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int qpnp_discover(struct platform_device *pdev,
+			struct qpnp_pinctrl *qctrl)
+{
+	struct device *dev = qctrl->dev;
+	struct pinctrl_pin_desc *desc, *descs;
+	struct qpnp_padinfo *pad, *pads;
+	unsigned int addr, npins;
+	int idx, ret;
+
+	npins = qctrl->info->npins;
+	pads = devm_kcalloc(dev, npins, sizeof(*pads), GFP_KERNEL);
+	if (!pads)
+		return -ENOMEM;
+
+	descs = devm_kcalloc(dev, npins, sizeof(*descs), GFP_KERNEL);
+	if (!descs)
+		return -ENOMEM;
+
+	for (idx = 0; idx < npins; idx++) {
+
+		pad = &pads[idx];
+		desc = &descs[idx];
+
+		pad->irq = platform_get_irq(pdev, idx);
+		if (pad->irq < 0)
+			return pad->irq;
+
+		pad->offset = qctrl->info->base + (idx * 0x100);
+
+		addr = QPNP_REG_ADDR(pad, QPNP_REG_DIG_MAJOR_REV);
+		ret = regmap_read(qctrl->map, addr, &pad->major);
+		if (ret < 0)
+			return ret;
+
+		addr = QPNP_REG_ADDR(pad, QPNP_REG_TYPE);
+		ret = regmap_read(qctrl->map, addr, &pad->type);
+		if (ret < 0)
+			return ret;
+
+		if (pad->type != qctrl->info->type) {
+			dev_err(dev, "Expected %x, found %x\n",
+				qctrl->info->type, pad->type);
+			return -EINVAL;
+		}
+
+		addr = QPNP_REG_ADDR(pad, QPNP_REG_SUBTYPE);
+		ret = regmap_read(qctrl->map, addr, &pad->subtype);
+		if (ret < 0)
+			return ret;
+
+		ret = qpnp_control_init(qctrl, pad);
+		if (ret)
+			return ret;
+
+		pad->name = qctrl->groups[idx];
+		desc->number = idx;
+		desc->name = pad->name;
+	}
+
+	qctrl->pads = pads;
+
+	qctrl->chip = qpnp_gpio_template;
+	qctrl->chip.dev = dev;
+	qctrl->chip.base = -1;
+	qctrl->chip.ngpio = qctrl->info->npins;
+	qctrl->chip.label = dev_name(dev);
+	qctrl->chip.of_gpio_n_cells = 2;
+	qctrl->chip.can_sleep = true;
+
+	qctrl->desc.pctlops = &qpnp_pinctrl_ops,
+	qctrl->desc.pmxops = &qpnp_pinmux_ops,
+	qctrl->desc.confops = &qpnp_pinconf_ops,
+	qctrl->desc.owner = THIS_MODULE,
+	qctrl->desc.name = dev_name(dev);
+	qctrl->desc.pins = descs;
+	qctrl->desc.npins = npins;
+
+	qctrl->ctrl = pinctrl_register(&qctrl->desc, dev, qctrl);
+	if (!qctrl->ctrl)
+		return -ENODEV;
+
+	ret = gpiochip_add(&qctrl->chip);
+	if (ret) {
+		dev_err(qctrl->dev, "can't add gpio chip\n");
+		goto err_chip;
+	}
+
+	ret = gpiochip_add_pin_range(&qctrl->chip, dev_name(dev),
+				     0, 0, npins);
+	if (ret) {
+		dev_err(dev, "failed to add pin range\n");
+		goto err_range;
+	}
+
+	return 0;
+
+err_chip:
+	pinctrl_unregister(qctrl->ctrl);
+
+err_range:
+	gpiochip_remove(&qctrl->chip);
+
+	return ret;
+
+}
+
+static const struct of_device_id qpnp_pinctrl_of_match[];
+
+static int qpnp_pinctrl_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	const struct qpnp_chipinfo *qchip;
+	struct qpnp_pinctrl *qctrl;
+
+	qctrl = devm_kzalloc(dev, sizeof(*qctrl), GFP_KERNEL);
+	if (!qctrl)
+		return -ENOMEM;
+
+	platform_set_drvdata(pdev, qctrl);
+
+	qchip = of_match_node(qpnp_pinctrl_of_match, dev->of_node)->data;
+
+	qctrl->info = qchip;
+	qctrl->dev = &pdev->dev;
+	qctrl->map = dev_get_regmap(dev->parent, NULL);
+
+	if (qchip->type == QPNP_GPIO_TYPE) {
+		if (WARN_ON(qchip->npins > ARRAY_SIZE(qpnp_gpio_groups)))
+			return -EINVAL;
+		qctrl->groups = qpnp_gpio_groups;
+		qctrl->functions = qpnp_gpio_functions;
+	} else {
+		if (WARN_ON(qchip->npins > ARRAY_SIZE(qpnp_mpp_groups)))
+			return -EINVAL;
+		qctrl->groups = qpnp_mpp_groups;
+		qctrl->functions = qpnp_mpp_functions;
+	}
+
+	return qpnp_discover(pdev, qctrl);
+}
+
+static int qpnp_pinctrl_remove(struct platform_device *pdev)
+{
+	struct qpnp_pinctrl *qctrl = platform_get_drvdata(pdev);
+
+	gpiochip_remove(&qctrl->chip);
+	pinctrl_unregister(qctrl->ctrl);
+
+	return 0;
+}
+
+static const struct qpnp_chipinfo qpnp_pm8841_mpp_info = {
+	.npins	= 4,
+	.base	= 0xa000,
+	.type   = QPNP_MPP_TYPE,
+};
+
+static const struct qpnp_chipinfo qpnp_pm8941_gpio_info = {
+	.npins	= 36,
+	.base	= 0xc000,
+	.type   = QPNP_GPIO_TYPE,
+};
+
+static const struct qpnp_chipinfo qpnp_pm8941_mpp_info = {
+	.npins	= 8,
+	.base	= 0xa000,
+	.type   = QPNP_MPP_TYPE,
+};
+
+static const struct qpnp_chipinfo qpnp_pma8084_mpp_info = {
+	.npins	= 4,
+	.base	= 0xa000,
+	.type   = QPNP_MPP_TYPE,
+};
+
+static const struct qpnp_chipinfo qpnp_pma8084_gpio_info = {
+	.npins	= 22,
+	.base	= 0xc000,
+	.type   = QPNP_GPIO_TYPE,
+};
+
+static const struct of_device_id qpnp_pinctrl_of_match[] = {
+	{ .compatible = "qcom,pm8941-gpio", .data = &qpnp_pm8941_gpio_info },
+	{ .compatible = "qcom,pm8941-mpp", .data = &qpnp_pm8941_mpp_info },
+	{ .compatible = "qcom,pm8841-mpp", .data = &qpnp_pm8841_mpp_info },
+	{ .compatible = "qcom,pma8084-gpio", .data = &qpnp_pma8084_gpio_info },
+	{ .compatible = "qcom,pma8084-mpp", .data = &qpnp_pma8084_mpp_info },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, qpnp_pinctrl_of_match);
+
+static struct platform_driver qpnp_pinctrl_driver = {
+	.driver = {
+		.name = "spmi-pmic-pinctrl",
+		.owner = THIS_MODULE,
+		.of_match_table = qpnp_pinctrl_of_match,
+	},
+	.probe = qpnp_pinctrl_probe,
+	.remove = qpnp_pinctrl_remove,
+};
+module_platform_driver(qpnp_pinctrl_driver);
+
+MODULE_AUTHOR("Ivan T. Ivanov <iivanov@xxxxxxxxxx>");
+MODULE_DESCRIPTION("Qualcomm SPMI PMIC pin control driver");
+MODULE_ALIAS("platform:spmi-pmic-pinctrl");
+MODULE_LICENSE("GPL v2");
-- 
1.8.3.2

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/