Re: [PATCH v2 1/3] pinctrl: qcom: Add APQ8084 pinctrl support

[Georgi Djakov]

On 08/29/2014 09:01 AM, Bjorn Andersson wrote:
> On Tue 26 Aug 05:45 PDT 2014, Georgi Djakov wrote:
> 
> Hi Georgi,
> 
> Sorry for missing this before, but I did a quick walkthrough and unfortunately
> the gpio configuration needs a few updates.
> 
>> diff --git a/drivers/pinctrl/qcom/pinctrl-apq8084.c b/drivers/pinctrl/qcom/pinctrl-apq8084.c
> [...]
>> +
>> +#define PINGROUP(id, f1, f2, f3, f4, f5, f6, f7)        \
>> +       {                                               \
>> +               .name = "gpio" #id,                     \
>> +               .pins = gpio##id##_pins,                \
>> +               .npins = ARRAY_SIZE(gpio##id##_pins),   \
>> +               .funcs = (int[]){                       \
>> +                       APQ_MUX_gpio,                   \
>> +                       APQ_MUX_##f1,                   \
>> +                       APQ_MUX_##f2,                   \
>> +                       APQ_MUX_##f3,                   \
>> +                       APQ_MUX_##f4,                   \
>> +                       APQ_MUX_##f5,                   \
>> +                       APQ_MUX_##f6,                   \
>> +                       APQ_MUX_##f7                    \
>> +               },                                      \
>> +               .nfuncs = 8,                            \
>> +               .ctl_reg = 0x1000 + 0x10 * id,          \
>> +               .io_reg = 0x1004 + 0x10 * id,           \
>> +               .intr_cfg_reg = 0x1008 + 0x10 * id,     \
>> +               .intr_status_reg = 0x100c + 0x10 * id,  \
>> +               .intr_target_reg = 0x400 + 0x4 * id,    \
> 
> The routing of the interrupt is specified in TLMM_GPIO_INTR_CFG(n),
> i.e: 0x1008 + 0x10 * n
> 
> Apparently the HW guys wanted to give us more work, so in 8084 they use 3 to
> specify routing the interrupts to KPSS, instead of the previous 4. So the
> static define of INTR_TARGET_PROC_APPS is no longer adequate.
> 
> My suggestion is that you create an additional patch and add to your series
> that moves todays hardcoded 4 into the soc_data for the existing platforms (or
> include it in this struct).
> 
>> +               .mux_bit = 2,                           \
>> +               .pull_bit = 0,                          \
>> +               .drv_bit = 6,                           \
>> +               .oe_bit = 9,                            \
>> +               .in_bit = 0,                            \
>> +               .out_bit = 1,                           \
>> +               .intr_enable_bit = 0,                   \
>> +               .intr_status_bit = 0,                   \
>> +               .intr_ack_high = 1,                     \
> 
> With the 8084 TLMM chip you ack the interrupt status by clearing this bit, so
> intr_ack_high should be 0.
> 
>> +               .intr_target_bit = 0,                   \
> 
> Target bit is 5.
> 
>> +               .intr_raw_status_bit = 3,               \
> 
> Raw interrupt status bit is 4.
> 
>> +               .intr_polarity_bit = 1,                 \
>> +               .intr_detection_bit = 2,                \
>> +               .intr_detection_width = 1,              \
> 
> You can do level, raise, fall and both edge detection with 8084, so the width
> of his part is 2.
> 
>> +       }
>> +
> 

Thanks Bjorn. I'll search for some more information regarding this and will
update accordingly, including the INTR_TARGET_PROC_APPS for each platform.
Thanks again for your time!

BR,
Georgi

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/