Re: [PATCH v2 1/2] ARM: dts: dra7: Add CPSW and MDIO module nodes for dra7

[Lennart Sorensen]

On Thu, Sep 11, 2014 at 12:07:45PM +0530, Mugunthan V N wrote:
> On Wednesday 10 September 2014 07:20 PM, Nishanth Menon wrote:
> > On 09/10/2014 08:37 AM, Mugunthan V N wrote:
> >> Add CPSW and MDIO related device tree data for DRA7XX and made as status
> >> disabled. Phy-id, pinmux for active and sleep state needs to be added in
> >> board dts files and enable the CPSW device.
> >>
> >> Signed-off-by: Mugunthan V N <mugunthanvnm@xxxxxx>
> >> ---
> >>  arch/arm/boot/dts/dra7.dtsi | 59 +++++++++++++++++++++++++++++++++++++++++++++
> >>  1 file changed, 59 insertions(+)
> >>
> >> diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi
> >> index d678152..8d79321 100644
> >> --- a/arch/arm/boot/dts/dra7.dtsi
> >> +++ b/arch/arm/boot/dts/dra7.dtsi
> >> @@ -34,6 +34,8 @@
> >>  		serial3 = &uart4;
> >>  		serial4 = &uart5;
> >>  		serial5 = &uart6;
> >> +		ethernet0 = &cpsw_emac0;
> >> +		ethernet1 = &cpsw_emac1;
> > 
> > should this rather be in board dts?
> 
> This should be here as the MAC address is filled in uboot with ethernet0
> and ethernet1, moving this to dts, the ordering of the ethernet can go
> for toss when they have other ethernet devices other than cpsw.
> 
> > 
> >>  	};
> >>  
> >>  	timer {
> >> @@ -1262,6 +1264,63 @@
> >>  			ti,irqs-skip = <10 133 139 140>;
> >>  			ti,irqs-safe-map = <0>;
> >>  		};
> >> +
> >> +		mac: ethernet@4a100000 {
> >> +			compatible = "ti,cpsw";
> >> +			ti,hwmods = "gmac";
> >> +			cpdma_channels = <8>;
> >> +			ale_entries = <1024>;
> >> +			bd_ram_size = <0x2000>;
> >> +			no_bd_ram = <0>;
> >> +			rx_descs = <64>;
> >> +			mac_control = <0x20>;
> >> +			slaves = <2>;
> >> +			active_slave = <0>;
> >> +			cpts_clock_mult = <0x80000000>;
> >> +			cpts_clock_shift = <29>;
> >> +			reg = <0x48484000 0x1000
> >> +			       0x48485200 0x2E00>;
> >> +			#address-cells = <1>;
> >> +			#size-cells = <1>;
> >> +			/*
> >> +			 * rx_thresh_pend
> >> +			 * rx_pend
> >> +			 * tx_pend
> >> +			 * misc_pend
> >> +			 */
> >> +			interrupts = <GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH>,
> >> +				     <GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>,
> >> +				     <GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH>,
> >> +				     <GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH>;
> >> +			ranges;
> >> +			status = "disabled";
> >> +
> >> +			davinci_mdio: mdio@48485000 {
> >> +				compatible = "ti,davinci_mdio";
> >> +				#address-cells = <1>;
> >> +				#size-cells = <0>;
> >> +				ti,hwmods = "davinci_mdio";
> >> +				bus_freq = <1000000>;
> >> +				reg = <0x48485000 0x100>;
> >> +			};
> >> +
> >> +			cpsw_emac0: slave@48480200 {
> >> +				/* Filled in by U-Boot */
> >> +				mac-address = [ 00 00 00 00 00 00 ];
> > 
> > should be disabled? what about platforms that do not have both emac ports?
> 
> the mac node is already disabled, so platforms which doesn't have emac
> should not enable this which in-turn emac node will be disabled.

I have the mac but I don't want to use both ports on the 2 port switch.
In fact in our case ethernet1 is a pru_eth interface.  Can a board dts
override the alias for ethernet1 or is that a syntax error?  I don't
think I tried that yet.

-- 
Len Sorensen
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/