[PATCH v4 3/4] pinctrl: Qualcomm SPMI PMIC GPIO pin controller driver

[Ivan T. Ivanov]

This is the pinctrl, pinmux, pinconf and gpiolib driver for the
Qualcomm GPIO sub-function blocks found in the PMIC chips.

Signed-off-by: Ivan T. Ivanov <iivanov@xxxxxxxxxx>
---
 drivers/pinctrl/qcom/Kconfig                  |  12 +
 drivers/pinctrl/qcom/Makefile                 |   1 +
 drivers/pinctrl/qcom/pinctrl-spmi-pmic-gpio.c | 942 ++++++++++++++++++++++++++
 3 files changed, 955 insertions(+)
 create mode 100644 drivers/pinctrl/qcom/pinctrl-spmi-pmic-gpio.c

diff --git a/drivers/pinctrl/qcom/Kconfig b/drivers/pinctrl/qcom/Kconfig
index d160a71..123248f 100644
--- a/drivers/pinctrl/qcom/Kconfig
+++ b/drivers/pinctrl/qcom/Kconfig
@@ -39,4 +39,16 @@ config PINCTRL_MSM8X74
 	  This is the pinctrl, pinmux, pinconf and gpiolib driver for the
 	  Qualcomm TLMM block found in the Qualcomm 8974 platform.
 
+config PINCTRL_SPMI_PMIC
+       tristate "Qualcomm SPMI PMIC pin controller driver"
+       depends on GPIOLIB && OF
+       select PINMUX
+       select PINCONF
+       select GENERIC_PINCONF
+       help
+         This is the pinctrl, pinmux, pinconf and gpiolib driver for the
+         Qualcomm GPIO and MPP blocks found in the Qualcomm PMIC's chips,
+         which are using SPMI for communication with SoC. Example PMIC's
+         devices are pm8841, pm8941 and pma8084.
+
 endif
diff --git a/drivers/pinctrl/qcom/Makefile b/drivers/pinctrl/qcom/Makefile
index 2a02602..396130c 100644
--- a/drivers/pinctrl/qcom/Makefile
+++ b/drivers/pinctrl/qcom/Makefile
@@ -4,3 +4,4 @@ obj-$(CONFIG_PINCTRL_APQ8064)	+= pinctrl-apq8064.o
 obj-$(CONFIG_PINCTRL_IPQ8064)	+= pinctrl-ipq8064.o
 obj-$(CONFIG_PINCTRL_MSM8960)	+= pinctrl-msm8960.o
 obj-$(CONFIG_PINCTRL_MSM8X74)	+= pinctrl-msm8x74.o
+obj-$(CONFIG_PINCTRL_SPMI_PMIC)	+= pinctrl-spmi-pmic-gpio.o
diff --git a/drivers/pinctrl/qcom/pinctrl-spmi-pmic-gpio.c b/drivers/pinctrl/qcom/pinctrl-spmi-pmic-gpio.c
new file mode 100644
index 0000000..493f0d3
--- /dev/null
+++ b/drivers/pinctrl/qcom/pinctrl-spmi-pmic-gpio.c
@@ -0,0 +1,942 @@
+/*
+ * Copyright (c) 2012-2014, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/gpio.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/pinctrl/pinconf-generic.h>
+#include <linux/pinctrl/pinconf.h>
+#include <linux/pinctrl/pinmux.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+#include <linux/types.h>
+
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+
+#include "../core.h"
+#include "../pinctrl-utils.h"
+
+#define PMIC_GPIO_ADDRESS_RANGE			0x100
+
+/* type and subtype registers base address offsets */
+#define PMIC_GPIO_REG_TYPE			0x4
+#define PMIC_GPIO_REG_SUBTYPE			0x5
+
+/* GPIO peripheral type and subtype out_values */
+#define PMIC_GPIO_TYPE				0x10
+#define PMIC_GPIO_SUBTYPE_GPIO_4CH		0x1
+#define PMIC_GPIO_SUBTYPE_GPIOC_4CH		0x5
+#define PMIC_GPIO_SUBTYPE_GPIO_8CH		0x9
+#define PMIC_GPIO_SUBTYPE_GPIOC_8CH		0xd
+
+#define PMIC_MPP_REG_RT_STS			0x10
+#define PMIC_MPP_REG_RT_STS_VAL_MASK		0x1
+
+/* control register base address offsets */
+#define PMIC_GPIO_REG_MODE_CTL			0x40
+#define PMIC_GPIO_REG_DIG_VIN_CTL		0x41
+#define PMIC_GPIO_REG_DIG_PULL_CTL		0x42
+#define PMIC_GPIO_REG_DIG_OUT_CTL		0x45
+#define PMIC_GPIO_REG_EN_CTL			0x46
+
+/* PMIC_GPIO_REG_MODE_CTL */
+#define PMIC_GPIO_REG_MODE_VALUE_SHIFT		0x1
+#define PMIC_GPIO_REG_MODE_FUNCTION_SHIFT	1
+#define PMIC_GPIO_REG_MODE_FUNCTION_MASK	0x7
+#define PMIC_GPIO_REG_MODE_DIR_SHIFT		4
+#define PMIC_GPIO_REG_MODE_DIR_MASK		0x7
+
+/* PMIC_GPIO_REG_DIG_VIN_CTL */
+#define PMIC_GPIO_REG_VIN_SHIFT			0
+#define PMIC_GPIO_REG_VIN_MASK			0x7
+
+/* PMIC_GPIO_REG_DIG_PULL_CTL */
+#define PMIC_GPIO_REG_PULL_SHIFT		0
+#define PMIC_GPIO_REG_PULL_MASK			0x7
+
+#define PMIC_GPIO_PULL_DOWN			4
+#define PMIC_GPIO_PULL_DISABLE			5
+
+/* PMIC_GPIO_REG_DIG_OUT_CTL */
+#define PMIC_GPIO_REG_OUT_STRENGTH_SHIFT	0
+#define PMIC_GPIO_REG_OUT_STRENGTH_MASK		0x3
+#define PMIC_GPIO_REG_OUT_TYPE_SHIFT		4
+#define PMIC_GPIO_REG_OUT_TYPE_MASK		0x3
+
+/*
+ * Output type - indicates pin should be configured as push-pull,
+ * open drain or open source.
+ */
+#define PMIC_GPIO_OUT_BUF_CMOS			0
+#define PMIC_GPIO_OUT_BUF_OPEN_DRAIN_NMOS	1
+#define PMIC_GPIO_OUT_BUF_OPEN_DRAIN_PMOS	2
+
+/* PMIC_GPIO_REG_EN_CTL */
+#define PMIC_GPIO_REG_MASTER_EN_SHIFT		7
+
+#define PMIC_GPIO_PHYSICAL_OFFSET		1
+
+/* Qualcomm specific pin configurations */
+#define PMIC_GPIO_CONF_PULL_UP			(PIN_CONFIG_END + 1)
+#define PMIC_GPIO_CONF_STRENGTH			(PIN_CONFIG_END + 2)
+
+/**
+ * struct pmic_gpio_pad - keep current GPIO settings
+ * @base: Address base in SPMI device.
+ * @irq: IRQ number which this GPIO generate.
+ * @is_enabled: Set to false when GPIO should be put in high Z state.
+ * @out_value: Cached pin output value
+ * @have_buffer: Set to true if GPIO output could be configured in push-pull,
+ *	open-drain or open-source mode.
+ * @output_enabled: Set to true if GPIO output logic is enabled.
+ * @input_enabled: Set to true if GPIO input buffer logic is enabled.
+ * @num_sources: Number of power-sources supported by this GPIO.
+ * @power_source: Current power-source used.
+ * @buffer_type: Push-pull, open-drain or open-source.
+ * @pullup: Constant current which flow trough GPIO output buffer.
+ * @strength: No, Low, Medium, High
+ * @function: See pmic_gpio_functions[]
+ */
+struct pmic_gpio_pad {
+	u16 base;
+	int irq;
+	bool is_enabled;
+	bool out_value;
+	bool have_buffer;
+	bool output_enabled;
+	bool input_enabled;
+	unsigned int num_sources;
+	unsigned int power_source;
+	unsigned int buffer_type;
+	unsigned int pullup;
+	unsigned int strength;
+	unsigned int function;
+};
+
+struct pmic_gpio_state {
+	struct device *dev;
+	struct regmap *map;
+	struct pinctrl_dev *ctrl;
+	struct gpio_chip chip;
+};
+
+struct pmic_gpio_bindings {
+	const char *property;
+	unsigned param;
+};
+
+static struct pmic_gpio_bindings pmic_gpio_bindings[] = {
+	{"qcom,pull-up-strength",	PMIC_GPIO_CONF_PULL_UP},
+	{"qcom,drive-strength",		PMIC_GPIO_CONF_STRENGTH},
+};
+
+static const char *const pmic_gpio_groups[] = {
+	"gpio1", "gpio2", "gpio3", "gpio4", "gpio5", "gpio6", "gpio7", "gpio8",
+	"gpio9", "gpio10", "gpio11", "gpio12", "gpio13", "gpio14", "gpio15",
+	"gpio16", "gpio17", "gpio18", "gpio19", "gpio20", "gpio21", "gpio22",
+	"gpio23", "gpio24", "gpio25", "gpio26", "gpio27", "gpio28", "gpio29",
+	"gpio30", "gpio31", "gpio32", "gpio33", "gpio34", "gpio35", "gpio36",
+};
+
+static const char *const pmic_gpio_functions[] = {
+	PMIC_GPIO_FUNC_NORMAL, PMIC_GPIO_FUNC_PAIRED,
+	PMIC_GPIO_FUNC_FUNC1, PMIC_GPIO_FUNC_FUNC2,
+	PMIC_GPIO_FUNC_DTEST1, PMIC_GPIO_FUNC_DTEST2,
+	PMIC_GPIO_FUNC_DTEST3, PMIC_GPIO_FUNC_DTEST4,
+};
+
+static int pmic_gpio_read(struct pmic_gpio_state *state,
+			  struct pmic_gpio_pad *pad, unsigned int addr)
+{
+	unsigned int val;
+	int ret;
+
+	ret = regmap_read(state->map, pad->base + addr, &val);
+	if (ret < 0)
+		dev_err(state->dev, "read 0x%x failed\n", addr);
+	else
+		ret = val;
+
+	return ret;
+}
+
+static int pmic_gpio_write(struct pmic_gpio_state *state,
+			   struct pmic_gpio_pad *pad, unsigned int addr,
+			   unsigned int val)
+{
+	int ret;
+
+	ret = regmap_write(state->map, pad->base + addr, val);
+	if (ret < 0)
+		dev_err(state->dev, "write 0x%x failed\n", addr);
+
+	return ret;
+}
+
+static int pmic_gpio_get_groups_count(struct pinctrl_dev *pctldev)
+{
+	/* Every PIN is a group */
+	return pctldev->desc->npins;
+}
+
+static const char *pmic_gpio_get_group_name(struct pinctrl_dev *pctldev,
+					    unsigned pin)
+{
+	return pctldev->desc->pins[pin].name;
+}
+
+static int pmic_gpio_get_group_pins(struct pinctrl_dev *pctldev, unsigned pin,
+				    const unsigned **pins, unsigned *num_pins)
+{
+	*pins = &pctldev->desc->pins[pin].number;
+	*num_pins = 1;
+	return 0;
+}
+
+static int pmic_gpio_parse_dt_config(struct device_node *np,
+				     struct pinctrl_dev *pctldev,
+				     unsigned long **configs,
+				     unsigned int *nconfs)
+{
+	struct pmic_gpio_bindings *par;
+	unsigned long cfg;
+	int ret, i;
+	u32 val;
+
+	for (i = 0; i < ARRAY_SIZE(pmic_gpio_bindings); i++) {
+
+		par = &pmic_gpio_bindings[i];
+		ret = of_property_read_u32(np, par->property, &val);
+
+		/* property not found */
+		if (ret == -EINVAL)
+			continue;
+
+		/* use zero as default value */
+		if (ret)
+			val = 0;
+
+		dev_dbg(pctldev->dev, "found %s with value %u\n",
+			par->property, val);
+
+		cfg = pinconf_to_config_packed(par->param, val);
+
+		ret = pinctrl_utils_add_config(pctldev, configs, nconfs, cfg);
+		if (ret)
+			return ret;
+	}
+
+	return 0;
+}
+
+static int pmic_gpio_dt_subnode_to_map(struct pinctrl_dev *pctldev,
+				       struct device_node *np,
+				       struct pinctrl_map **map,
+				       unsigned *reserv, unsigned *nmaps,
+				       enum pinctrl_map_type type)
+{
+	unsigned long *configs = NULL;
+	unsigned nconfs = 0;
+	struct property *prop;
+	const char *group;
+	int ret;
+
+	ret = pmic_gpio_parse_dt_config(np, pctldev, &configs, &nconfs);
+	if (ret < 0)
+		return ret;
+
+	if (!nconfs)
+		return 0;
+
+	ret = of_property_count_strings(np, "pins");
+	if (ret < 0)
+		goto exit;
+
+	ret = pinctrl_utils_reserve_map(pctldev, map, reserv, nmaps, ret);
+	if (ret < 0)
+		goto exit;
+
+	of_property_for_each_string(np, "pins", prop, group) {
+		ret = pinctrl_utils_add_map_configs(pctldev, map,
+						    reserv, nmaps, group,
+						    configs, nconfs, type);
+		if (ret < 0)
+			break;
+	}
+exit:
+	kfree(configs);
+	return ret;
+}
+
+static int pmic_gpio_dt_node_to_map(struct pinctrl_dev *pctldev,
+				    struct device_node *np_config,
+				    struct pinctrl_map **map, unsigned *nmaps)
+{
+	enum pinctrl_map_type type;
+	struct device_node *np;
+	unsigned reserv;
+	int ret;
+
+	ret = 0;
+	*map = NULL;
+	*nmaps = 0;
+	reserv = 0;
+	type = PIN_MAP_TYPE_CONFIGS_GROUP;
+
+	for_each_child_of_node(np_config, np) {
+
+		ret = pinconf_generic_dt_subnode_to_map(pctldev, np, map,
+							&reserv, nmaps, type);
+		if (ret)
+			break;
+
+		ret = pmic_gpio_dt_subnode_to_map(pctldev, np, map, &reserv,
+						  nmaps, type);
+		if (ret)
+			break;
+	}
+
+	if (ret < 0)
+		pinctrl_utils_dt_free_map(pctldev, *map, *nmaps);
+
+	return ret;
+}
+
+static const struct pinctrl_ops pmic_gpio_pinctrl_ops = {
+	.get_groups_count	= pmic_gpio_get_groups_count,
+	.get_group_name		= pmic_gpio_get_group_name,
+	.get_group_pins		= pmic_gpio_get_group_pins,
+	.dt_node_to_map		= pmic_gpio_dt_node_to_map,
+	.dt_free_map		= pinctrl_utils_dt_free_map,
+};
+
+static int pmic_gpio_get_functions_count(struct pinctrl_dev *pctldev)
+{
+	return ARRAY_SIZE(pmic_gpio_functions);
+}
+
+static const char *pmic_gpio_get_function_name(struct pinctrl_dev *pctldev,
+					       unsigned function)
+{
+	return pmic_gpio_functions[function];
+}
+
+static int pmic_gpio_get_function_groups(struct pinctrl_dev *pctldev,
+					 unsigned function,
+					 const char *const **groups,
+					 unsigned *const num_qgroups)
+{
+	*groups = pmic_gpio_groups;
+	*num_qgroups = pctldev->desc->npins;
+	return 0;
+}
+
+static int pmic_gpio_pinmux_enable(struct pinctrl_dev *pctldev,
+				   unsigned function, unsigned pin)
+{
+	struct pmic_gpio_state *state = pinctrl_dev_get_drvdata(pctldev);
+	struct pmic_gpio_pad *pad;
+	unsigned int val;
+	int ret;
+
+	pad = pctldev->desc->pins[pin].drv_data;
+
+	pad->function = function;
+
+	val = 0;
+	if (pad->output_enabled) {
+		if (pad->input_enabled)
+			val = 2;
+		else
+			val = 1;
+	}
+
+	val |= pad->function << PMIC_GPIO_REG_MODE_FUNCTION_SHIFT;
+	val |= pad->out_value & PMIC_GPIO_REG_MODE_VALUE_SHIFT;
+
+	ret = pmic_gpio_write(state, pad, PMIC_GPIO_REG_MODE_CTL, val);
+	if (ret < 0)
+		return ret;
+
+	val = pad->is_enabled << PMIC_GPIO_REG_MASTER_EN_SHIFT;
+
+	return pmic_gpio_write(state, pad, PMIC_GPIO_REG_EN_CTL, val);
+}
+
+static const struct pinmux_ops pmic_gpio_pinmux_ops = {
+	.get_functions_count	= pmic_gpio_get_functions_count,
+	.get_function_name	= pmic_gpio_get_function_name,
+	.get_function_groups	= pmic_gpio_get_function_groups,
+	.enable			= pmic_gpio_pinmux_enable,
+};
+
+static int pmic_gpio_config_get(struct pinctrl_dev *pctldev,
+				unsigned int pin, unsigned long *config)
+{
+	unsigned param = pinconf_to_config_param(*config);
+	struct pmic_gpio_pad *pad;
+	unsigned arg;
+
+	pad = pctldev->desc->pins[pin].drv_data;
+
+	switch (param) {
+	case PIN_CONFIG_DRIVE_PUSH_PULL:
+		arg = pad->buffer_type == PMIC_GPIO_OUT_BUF_CMOS;
+		break;
+	case PIN_CONFIG_DRIVE_OPEN_DRAIN:
+		arg = pad->buffer_type == PMIC_GPIO_OUT_BUF_OPEN_DRAIN_NMOS;
+		break;
+	case PIN_CONFIG_DRIVE_OPEN_SOURCE:
+		arg = pad->buffer_type == PMIC_GPIO_OUT_BUF_OPEN_DRAIN_PMOS;
+		break;
+	case PIN_CONFIG_BIAS_PULL_DOWN:
+		arg = pad->pullup == PMIC_GPIO_PULL_DOWN;
+		break;
+	case PIN_CONFIG_BIAS_DISABLE:
+		arg = pad->pullup = PMIC_GPIO_PULL_DISABLE;
+		break;
+	case PIN_CONFIG_BIAS_PULL_UP:
+		arg = pad->pullup == PMIC_GPIO_PULL_UP_30;
+		break;
+		break;
+	case PIN_CONFIG_BIAS_HIGH_IMPEDANCE:
+		arg = !pad->is_enabled;
+		break;
+	case PIN_CONFIG_POWER_SOURCE:
+		arg = pad->power_source;
+		break;
+	case PIN_CONFIG_INPUT_ENABLE:
+		arg = pad->input_enabled;
+		break;
+	case PIN_CONFIG_OUTPUT:
+		arg = pad->out_value;
+		break;
+	case PMIC_GPIO_CONF_PULL_UP:
+		arg = pad->pullup;
+		break;
+	case PMIC_GPIO_CONF_STRENGTH:
+		arg = pad->strength;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	*config = pinconf_to_config_packed(param, arg);
+	return 0;
+}
+
+static int pmic_gpio_config_set(struct pinctrl_dev *pctldev, unsigned int pin,
+				unsigned long *configs, unsigned nconfs)
+{
+	struct pmic_gpio_state *state = pinctrl_dev_get_drvdata(pctldev);
+	struct pmic_gpio_pad *pad;
+	unsigned param, arg;
+	unsigned int val;
+	int i, ret;
+
+	pad = pctldev->desc->pins[pin].drv_data;
+
+	for (i = 0; i < nconfs; i++) {
+		param = pinconf_to_config_param(configs[i]);
+		arg = pinconf_to_config_argument(configs[i]);
+
+		switch (param) {
+		case PIN_CONFIG_DRIVE_PUSH_PULL:
+			pad->buffer_type = PMIC_GPIO_OUT_BUF_CMOS;
+			break;
+		case PIN_CONFIG_DRIVE_OPEN_DRAIN:
+			if (!pad->have_buffer)
+				return -EINVAL;
+			pad->buffer_type = PMIC_GPIO_OUT_BUF_OPEN_DRAIN_NMOS;
+			break;
+		case PIN_CONFIG_DRIVE_OPEN_SOURCE:
+			if (!pad->have_buffer)
+				return -EINVAL;
+			pad->buffer_type = PMIC_GPIO_OUT_BUF_OPEN_DRAIN_PMOS;
+			break;
+		case PIN_CONFIG_BIAS_DISABLE:
+			pad->pullup = PMIC_GPIO_PULL_DISABLE;
+			break;
+		case PIN_CONFIG_BIAS_PULL_UP:
+			pad->pullup = PMIC_GPIO_PULL_UP_30;
+			break;
+		case PIN_CONFIG_BIAS_PULL_DOWN:
+			if (arg)
+				pad->pullup = PMIC_GPIO_PULL_DOWN;
+			else
+				pad->pullup = PMIC_GPIO_PULL_DISABLE;
+			break;
+		case PIN_CONFIG_BIAS_HIGH_IMPEDANCE:
+			pad->is_enabled = false;
+			break;
+		case PIN_CONFIG_POWER_SOURCE:
+			if (arg > pad->num_sources)
+				return -EINVAL;
+			pad->power_source = arg;
+			break;
+		case PIN_CONFIG_INPUT_ENABLE:
+			pad->input_enabled = arg ? true : false;
+			break;
+		case PIN_CONFIG_OUTPUT:
+			pad->output_enabled = true;
+			pad->out_value = arg;
+			break;
+		case PMIC_GPIO_CONF_PULL_UP:
+			if (arg > PMIC_GPIO_PULL_UP_1P5_30)
+				return -EINVAL;
+			pad->pullup = arg;
+			break;
+		case PMIC_GPIO_CONF_STRENGTH:
+			if (arg > PMIC_GPIO_STRENGTH_LOW)
+				return -EINVAL;
+			pad->strength = arg;
+			break;
+		default:
+			return -EINVAL;
+		}
+	}
+
+	val = pad->power_source << PMIC_GPIO_REG_VIN_SHIFT;
+
+	ret = pmic_gpio_write(state, pad, PMIC_GPIO_REG_DIG_VIN_CTL, val);
+	if (ret < 0)
+		return ret;
+
+	val = pad->pullup << PMIC_GPIO_REG_PULL_SHIFT;
+
+	ret = pmic_gpio_write(state, pad, PMIC_GPIO_REG_DIG_PULL_CTL, val);
+	if (ret < 0)
+		return ret;
+
+	val = pad->buffer_type << PMIC_GPIO_REG_OUT_TYPE_SHIFT;
+	val = pad->strength << PMIC_GPIO_REG_OUT_STRENGTH_SHIFT;
+
+	ret = pmic_gpio_write(state, pad, PMIC_GPIO_REG_DIG_OUT_CTL, val);
+	if (ret < 0)
+		return ret;
+
+	val = 0;
+	if (pad->output_enabled) {
+		if (pad->input_enabled)
+			val = 2;
+		else
+			val = 1;
+	}
+
+	val = val << PMIC_GPIO_REG_MODE_DIR_SHIFT;
+	val |= pad->function << PMIC_GPIO_REG_MODE_FUNCTION_SHIFT;
+	val |= pad->out_value & PMIC_GPIO_REG_MODE_VALUE_SHIFT;
+
+	return pmic_gpio_write(state, pad, PMIC_GPIO_REG_MODE_CTL, val);
+}
+
+static void pmic_gpio_config_dbg_show(struct pinctrl_dev *pctldev,
+				      struct seq_file *s, unsigned pin)
+{
+	struct pmic_gpio_state *state = pinctrl_dev_get_drvdata(pctldev);
+	struct pmic_gpio_pad *pad;
+	int ret, val;
+
+	static const char *const biases[] = {
+		"pull-up 30uA", "pull-up 1.5uA", "pull-up 31.5uA",
+		"pull-up 1.5uA + 30uA boost", "pull-down 10uA", "no pull"
+	};
+	static const char *const buffer_types[] = {
+		"push-pull", "open-drain", "open-source"
+	};
+	static const char *const strengths[] = {
+		"no", "high", "medium", "low"
+	};
+
+	pad = pctldev->desc->pins[pin].drv_data;
+
+	seq_printf(s, " gpio%-2d:", pin + PMIC_GPIO_PHYSICAL_OFFSET);
+
+	val = pmic_gpio_read(state, pad, PMIC_GPIO_REG_EN_CTL);
+
+	if (val < 0 || !(val >> PMIC_GPIO_REG_MASTER_EN_SHIFT)) {
+		seq_puts(s, " ---");
+	} else {
+
+		if (!pad->input_enabled) {
+			ret = pmic_gpio_read(state, pad, PMIC_MPP_REG_RT_STS);
+			if (!ret) {
+				ret &= PMIC_MPP_REG_RT_STS_VAL_MASK;
+				pad->out_value = ret;
+			}
+		}
+
+		seq_printf(s, " %-4s", pad->output_enabled ? "out" : "in");
+		seq_printf(s, " %-7s", pmic_gpio_functions[pad->function]);
+		seq_printf(s, " vin-%d", pad->power_source);
+		seq_printf(s, " %-27s", biases[pad->pullup]);
+		seq_printf(s, " %-10s", buffer_types[pad->buffer_type]);
+		seq_printf(s, " %-4s", pad->out_value ? "high" : "low");
+		seq_printf(s, " %-7s", strengths[pad->strength]);
+	}
+}
+
+static const struct pinconf_ops pmic_gpio_pinconf_ops = {
+	.pin_config_group_get		= pmic_gpio_config_get,
+	.pin_config_group_set		= pmic_gpio_config_set,
+	.pin_config_group_dbg_show	= pmic_gpio_config_dbg_show,
+};
+
+static int pmic_gpio_direction_input(struct gpio_chip *chip, unsigned pin)
+{
+	struct pmic_gpio_state *state;
+	unsigned long config;
+
+	state = container_of(chip, struct pmic_gpio_state, chip);
+	config = pinconf_to_config_packed(PIN_CONFIG_INPUT_ENABLE, 1);
+
+	return pmic_gpio_config_set(state->ctrl, pin, &config, 1);
+}
+
+static int pmic_gpio_direction_output(struct gpio_chip *chip,
+				      unsigned pin, int val)
+{
+	struct pmic_gpio_state *state;
+	unsigned long config;
+
+	state = container_of(chip, struct pmic_gpio_state, chip);
+	config = pinconf_to_config_packed(PIN_CONFIG_OUTPUT, val);
+
+	return pmic_gpio_config_set(state->ctrl, pin, &config, 1);
+}
+
+static int pmic_gpio_get(struct gpio_chip *chip, unsigned pin)
+{
+	struct pmic_gpio_state *state;
+	struct pmic_gpio_pad *pad;
+	int ret;
+
+	state = container_of(chip, struct pmic_gpio_state, chip);
+	pad = state->ctrl->desc->pins[pin].drv_data;
+
+	if (!pad->is_enabled)
+		return -EINVAL;
+
+	if (pad->input_enabled) {
+		ret = pmic_gpio_read(state, pad, PMIC_MPP_REG_RT_STS);
+		if (ret < 0)
+			return ret;
+
+		pad->out_value = ret & PMIC_MPP_REG_RT_STS_VAL_MASK;
+	}
+
+	return pad->out_value;
+}
+
+static void pmic_gpio_set(struct gpio_chip *chip, unsigned pin, int value)
+{
+	struct pmic_gpio_state *state;
+	unsigned long config;
+
+	state = container_of(chip, struct pmic_gpio_state, chip);
+	config = pinconf_to_config_packed(PIN_CONFIG_OUTPUT, value);
+
+	pmic_gpio_config_set(state->ctrl, pin, &config, 1);
+}
+
+static int pmic_gpio_request(struct gpio_chip *chip, unsigned base)
+{
+	return pinctrl_request_gpio(chip->base + base);
+}
+
+static void pmic_gpio_free(struct gpio_chip *chip, unsigned base)
+{
+	pinctrl_free_gpio(chip->base + base);
+}
+
+static int pmic_gpio_of_xlate(struct gpio_chip *chip,
+			      const struct of_phandle_args *gpio_desc,
+			      u32 *flags)
+{
+	if (chip->of_gpio_n_cells < 2)
+		return -EINVAL;
+
+	if (flags)
+		*flags = gpio_desc->args[1];
+
+	return gpio_desc->args[0] - PMIC_GPIO_PHYSICAL_OFFSET;
+}
+
+static int pmic_gpio_to_irq(struct gpio_chip *chip, unsigned pin)
+{
+	struct pmic_gpio_state *state;
+	struct pmic_gpio_pad *pad;
+
+	state = container_of(chip, struct pmic_gpio_state, chip);
+	pad = state->ctrl->desc->pins[pin].drv_data;
+
+	return pad->irq;
+}
+
+static void pmic_gpio_dbg_show(struct seq_file *s, struct gpio_chip *chip)
+{
+	struct pmic_gpio_state *state;
+	unsigned i;
+
+	state = container_of(chip, struct pmic_gpio_state, chip);
+
+	for (i = 0; i < chip->ngpio; i++) {
+		pmic_gpio_config_dbg_show(state->ctrl, s, i);
+		seq_puts(s, "\n");
+	}
+}
+
+static const struct gpio_chip pmic_gpio_gpio_template = {
+	.direction_input	= pmic_gpio_direction_input,
+	.direction_output	= pmic_gpio_direction_output,
+	.get			= pmic_gpio_get,
+	.set			= pmic_gpio_set,
+	.request		= pmic_gpio_request,
+	.free			= pmic_gpio_free,
+	.of_xlate		= pmic_gpio_of_xlate,
+	.to_irq			= pmic_gpio_to_irq,
+	.dbg_show		= pmic_gpio_dbg_show,
+};
+
+static int pmic_gpio_populate(struct pmic_gpio_state *state,
+			      struct pmic_gpio_pad *pad)
+{
+	int type, subtype, val, dir;
+
+	type = pmic_gpio_read(state, pad, PMIC_GPIO_REG_TYPE);
+	if (type < 0)
+		return type;
+
+	if (type != PMIC_GPIO_TYPE) {
+		dev_err(state->dev, "incorrect block type 0x%x at 0x%x\n",
+			type, pad->base);
+		return -ENODEV;
+	}
+
+	subtype = pmic_gpio_read(state, pad, PMIC_GPIO_REG_SUBTYPE);
+	if (subtype < 0)
+		return subtype;
+
+	switch (subtype) {
+	case PMIC_GPIO_SUBTYPE_GPIO_4CH:
+		pad->have_buffer = true;
+	case PMIC_GPIO_SUBTYPE_GPIOC_4CH:
+		pad->num_sources = 4;
+		break;
+	case PMIC_GPIO_SUBTYPE_GPIO_8CH:
+		pad->have_buffer = true;
+	case PMIC_GPIO_SUBTYPE_GPIOC_8CH:
+		pad->num_sources = 8;
+		break;
+	default:
+		dev_err(state->dev, "unknown GPIO type 0x%x\n", subtype);
+		return -ENODEV;
+	}
+
+	val = pmic_gpio_read(state, pad, PMIC_GPIO_REG_MODE_CTL);
+	if (val < 0)
+		return val;
+
+	pad->out_value = val & PMIC_GPIO_REG_MODE_VALUE_SHIFT;
+
+	dir = val >> PMIC_GPIO_REG_MODE_DIR_SHIFT;
+	dir &= PMIC_GPIO_REG_MODE_DIR_MASK;
+	switch (dir) {
+	case 0:
+		pad->input_enabled = true;
+		pad->output_enabled = false;
+		break;
+	case 1:
+		pad->input_enabled = false;
+		pad->output_enabled = true;
+		break;
+	case 2:
+		pad->input_enabled = true;
+		pad->output_enabled = true;
+		break;
+	default:
+		dev_err(state->dev, "unknown GPIO direction\n");
+		return -ENODEV;
+	}
+
+	pad->function = val >> PMIC_GPIO_REG_MODE_FUNCTION_SHIFT;
+	pad->function &= PMIC_GPIO_REG_MODE_FUNCTION_MASK;
+
+	val = pmic_gpio_read(state, pad, PMIC_GPIO_REG_DIG_VIN_CTL);
+	if (val < 0)
+		return val;
+
+	pad->power_source = val >> PMIC_GPIO_REG_VIN_SHIFT;
+	pad->power_source &= PMIC_GPIO_REG_VIN_MASK;
+
+	val = pmic_gpio_read(state, pad, PMIC_GPIO_REG_DIG_PULL_CTL);
+	if (val < 0)
+		return val;
+
+	pad->pullup = val >> PMIC_GPIO_REG_PULL_SHIFT;
+	pad->pullup &= PMIC_GPIO_REG_PULL_MASK;
+
+	val = pmic_gpio_read(state, pad, PMIC_GPIO_REG_DIG_OUT_CTL);
+	if (val < 0)
+		return val;
+
+	pad->strength = val >> PMIC_GPIO_REG_OUT_STRENGTH_SHIFT;
+	pad->strength &= PMIC_GPIO_REG_OUT_STRENGTH_MASK;
+
+	pad->buffer_type = val >> PMIC_GPIO_REG_OUT_TYPE_SHIFT;
+	pad->buffer_type &= PMIC_GPIO_REG_OUT_TYPE_MASK;
+
+	/* Pin could be disabled with PIN_CONFIG_BIAS_HIGH_IMPEDANCE */
+	pad->is_enabled = true;
+	return 0;
+}
+
+static int pmic_gpio_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct pinctrl_pin_desc *pindesc;
+	struct pinctrl_desc *pctrldesc;
+	struct pmic_gpio_pad *pad, *pads;
+	struct pmic_gpio_state *state;
+	int ret, npins, i;
+	u32 res[2];
+
+	ret = of_property_read_u32_array(dev->of_node, "reg", res, 2);
+	if (ret < 0) {
+		dev_err(dev, "missing base address and/or range");
+		return ret;
+	}
+
+	npins = res[1] / PMIC_GPIO_ADDRESS_RANGE;
+
+	if (!npins)
+		return -EINVAL;
+
+	BUG_ON(npins > ARRAY_SIZE(pmic_gpio_groups));
+
+	state = devm_kzalloc(dev, sizeof(*state), GFP_KERNEL);
+	if (!state)
+		return -ENOMEM;
+
+	platform_set_drvdata(pdev, state);
+
+	state->dev = &pdev->dev;
+	state->map = dev_get_regmap(dev->parent, NULL);
+
+	pindesc = devm_kcalloc(dev, npins, sizeof(*pindesc), GFP_KERNEL);
+	if (!pindesc)
+		return -ENOMEM;
+
+	pads = devm_kcalloc(dev, npins, sizeof(*pads), GFP_KERNEL);
+	if (!pads)
+		return -ENOMEM;
+
+	pctrldesc = devm_kzalloc(dev, sizeof(*pctrldesc), GFP_KERNEL);
+	if (!pctrldesc)
+		return -ENOMEM;
+
+	pctrldesc->pctlops = &pmic_gpio_pinctrl_ops;
+	pctrldesc->pmxops = &pmic_gpio_pinmux_ops;
+	pctrldesc->confops = &pmic_gpio_pinconf_ops;
+	pctrldesc->owner = THIS_MODULE;
+	pctrldesc->name = dev_name(dev);
+	pctrldesc->pins = pindesc;
+	pctrldesc->npins = npins;
+
+	for (i = 0; i < npins; i++, pindesc++) {
+		pad = &pads[i];
+		pindesc->drv_data = pad;
+		pindesc->number = i;
+		pindesc->name = pmic_gpio_groups[i];
+
+		pad->irq = platform_get_irq(pdev, i);
+		if (pad->irq < 0)
+			return pad->irq;
+
+		pad->base = res[0] + i * PMIC_GPIO_ADDRESS_RANGE;
+
+		ret = pmic_gpio_populate(state, pad);
+		if (ret < 0)
+			return ret;
+	}
+
+	state->chip = pmic_gpio_gpio_template;
+	state->chip.dev = dev;
+	state->chip.base = -1;
+	state->chip.ngpio = npins;
+	state->chip.label = dev_name(dev);
+	state->chip.of_gpio_n_cells = 2;
+	state->chip.can_sleep = false;
+
+	state->ctrl = pinctrl_register(pctrldesc, dev, state);
+	if (!state->ctrl)
+		return -ENODEV;
+
+	ret = gpiochip_add(&state->chip);
+	if (ret) {
+		dev_err(state->dev, "can't add gpio chip\n");
+		goto err_chip;
+	}
+
+	ret = gpiochip_add_pin_range(&state->chip, dev_name(dev), 0, 0, npins);
+	if (ret) {
+		dev_err(dev, "failed to add pin range\n");
+		goto err_range;
+	}
+
+	return 0;
+
+err_range:
+	gpiochip_remove(&state->chip);
+err_chip:
+	pinctrl_unregister(state->ctrl);
+	return ret;
+}
+
+static int pmic_gpio_remove(struct platform_device *pdev)
+{
+	struct pmic_gpio_state *state = platform_get_drvdata(pdev);
+	int ret;
+
+	ret = gpiochip_remove(&state->chip);
+	if (ret < 0)
+		return ret;
+
+	pinctrl_unregister(state->ctrl);
+	return 0;
+}
+
+static const struct of_device_id pmic_gpio_of_match[] = {
+	{ .compatible = "qcom,spmi-pmic-gpio" },
+	{ },
+};
+
+MODULE_DEVICE_TABLE(of, pmic_gpio_of_match);
+
+static struct platform_driver pmic_gpio_driver = {
+	.driver = {
+		   .name = "spmi-pmic-gpio",
+		   .owner = THIS_MODULE,
+		   .of_match_table = pmic_gpio_of_match,
+	},
+	.probe	= pmic_gpio_probe,
+	.remove = pmic_gpio_remove,
+};
+
+module_platform_driver(pmic_gpio_driver);
+
+MODULE_AUTHOR("Ivan T. Ivanov <iivanov@xxxxxxxxxx>");
+MODULE_DESCRIPTION("Qualcomm SPMI PMIC GPIO pin control driver");
+MODULE_ALIAS("platform:spmi-pmic-gpio");
+MODULE_LICENSE("GPL v2");
-- 
1.9.1

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/