Re: [PATCH v2 4/7] ARM: dts: sun9i: Add A80 Optimus Board support

[Maxime Ripard]

On Sat, Sep 27, 2014 at 09:10:48PM +0800, Chen-Yu Tsai wrote:
> On Thu, Sep 25, 2014 at 9:34 PM, Maxime Ripard
> <maxime.ripard@xxxxxxxxxxxxxxxxxx> wrote:
> > On Wed, Sep 24, 2014 at 10:48:58PM +0800, Chen-Yu Tsai wrote:
> >> The A80 Optimus Board is was launched with the Allwinner A80 SoC.
> >> It was jointly developed by Allwinner and Merrii.
> >>
> >> This board has a UART port, a JTAG connector, USB host ports, a USB
> >> 3.0 OTG connector, an HDMI output, a micro SD slot, 8G NAND flash,
> >> 4G DRAM, a camera sensor interface, a WiFi/BT combo chip, a headphone
> >> jack, IR receiver, and additional GPIO headers.
> >>
> >> This patch adds only basic support.
> >>
> >> Signed-off-by: Chen-Yu Tsai <wens@xxxxxxxx>
> >> ---
> >>  arch/arm/boot/dts/Makefile              |  2 +
> >>  arch/arm/boot/dts/sun9i-a80-optimus.dts | 66 +++++++++++++++++++++++++++++++++
> >>  2 files changed, 68 insertions(+)
> >>  create mode 100644 arch/arm/boot/dts/sun9i-a80-optimus.dts
> >>
> >> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> >> index 2f42b18..098f319 100644
> >> --- a/arch/arm/boot/dts/Makefile
> >> +++ b/arch/arm/boot/dts/Makefile
> >> @@ -424,6 +424,8 @@ dtb-$(CONFIG_MACH_SUN7I) += \
> >>       sun7i-a20-pcduino3.dtb
> >>  dtb-$(CONFIG_MACH_SUN8I) += \
> >>       sun8i-a23-ippo-q8h-v5.dtb
> >> +dtb-$(CONFIG_MACH_SUN9I) += \
> >> +     sun9i-a80-optimus.dtb
> >>  dtb-$(CONFIG_ARCH_TEGRA) += tegra20-harmony.dtb \
> >>       tegra20-iris-512.dtb \
> >>       tegra20-medcom-wide.dtb \
> >> diff --git a/arch/arm/boot/dts/sun9i-a80-optimus.dts b/arch/arm/boot/dts/sun9i-a80-optimus.dts
> >> new file mode 100644
> >> index 0000000..f83abab
> >> --- /dev/null
> >> +++ b/arch/arm/boot/dts/sun9i-a80-optimus.dts
> >> @@ -0,0 +1,66 @@
> >> +/*
> >> + * Copyright 2014 Chen-Yu Tsai
> >> + *
> >> + * Chen-Yu Tsai <wens@xxxxxxxx>
> >> + *
> >> + * This file is dual-licensed: you can use it either under the terms
> >> + * of the GPL or the X11 license, at your option. Note that this dual
> >> + * licensing only applies to this file, and not this project as a
> >> + * whole.
> >> + *
> >> + *  a) This library is free software; you can redistribute it and/or
> >> + *     modify it under the terms of the GNU General Public License as
> >> + *     published by the Free Software Foundation; either version 2 of the
> >> + *     License, or (at your option) any later version.
> >> + *
> >> + *     This library is distributed in the hope that it will be useful,
> >> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> >> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> >> + *     GNU General Public License for more details.
> >> + *
> >> + *     You should have received a copy of the GNU General Public
> >> + *     License along with this library; if not, write to the Free
> >> + *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
> >> + *     MA 02110-1301 USA
> >> + *
> >> + * Or, alternatively,
> >> + *
> >> + *  b) Permission is hereby granted, free of charge, to any person
> >> + *     obtaining a copy of this software and associated documentation
> >> + *     files (the "Software"), to deal in the Software without
> >> + *     restriction, including without limitation the rights to use,
> >> + *     copy, modify, merge, publish, distribute, sublicense, and/or
> >> + *     sell copies of the Software, and to permit persons to whom the
> >> + *     Software is furnished to do so, subject to the following
> >> + *     conditions:
> >> + *
> >> + *     The above copyright notice and this permission notice shall be
> >> + *     included in all copies or substantial portions of the Software.
> >> + *
> >> + *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> >> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> >> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> >> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> >> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> >> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> >> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> >> + *     OTHER DEALINGS IN THE SOFTWARE.
> >> + */
> >> +
> >> +/dts-v1/;
> >> +/include/ "sun9i-a80.dtsi"
> >> +
> >> +/ {
> >> +     model = "Merrii A80 Optimus Board";
> >> +     compatible = "merrii,a80-optimus", "allwinner,sun9i-a80";
> >> +
> >> +     chosen {
> >> +             bootargs = "earlyprintk console=ttyS0,115200";
> >> +     };
> >
> > Since you changed the memory node in the DTSI, you should probably add
> > one here too, don't you?
> 
> I thought we left fixing that to the bootloader?
> I don't see any memory nodes in our other DTS.

Yes, but does the A80 bootloader supports DT and actually fixes it? If
not, then you'll still have to have a memory node, just like on the
A31 (and presumably on the A23).

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

Attachment: signature.asc
Description: Digital signature