Re: [PATCH] mmc:core: fix hs400 timing selection

[Jaehoon Chung]

Hi, Chanho.

On 10/22/2014 11:55 AM, Chanho Min wrote:
> According to JEDEC v5.01 spec (6.6.5), In order to switch to HS400 mode,
> host should perform the following steps.
> 
>  1. HS200 mode selection completed
>  2. Set HS_TIMING to 0x01(High Speed)
>  3. Host changes frequency to =< 52MHz
>  4. Set the bus width to DDR 8bit (CMD6)
>  5. Host may read Driver Strength (CMD8)
>  6. Set HS_TIMING to 0x03 (HS400)
> 
> In current implementation, the order of 2 and 3 is reversed.
> The HS_TIMING field should be set to 0x1 before the clock frequency
> is set to a value not greater than 52 MHz. Otherwise, Initialization of
> timing can be failed. Also, the host contoller's UHS timing mode should
> be set to DDR50 after the bus width is set to DDR 8bit.
> 
> Signed-off-by: Hankyung Yu <hankyung.yu@xxxxxxx>
> Signed-off-by: Chanho Min <chanho.min@xxxxxxx>
> ---
>  drivers/mmc/core/mmc.c |   13 ++++++++++---
>  1 file changed, 10 insertions(+), 3 deletions(-)
> 
> diff --git a/drivers/mmc/core/mmc.c b/drivers/mmc/core/mmc.c
> index a301a78..52f78e0 100644
> --- a/drivers/mmc/core/mmc.c
> +++ b/drivers/mmc/core/mmc.c
> @@ -1061,9 +1061,6 @@ static int mmc_select_hs400(struct mmc_card *card)
>  	 * Before switching to dual data rate operation for HS400,
>  	 * it is required to convert from HS200 mode to HS mode.
>  	 */
> -	mmc_set_timing(card->host, MMC_TIMING_MMC_HS);
> -	mmc_set_bus_speed(card);
> -
>  	err = __mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
>  			   EXT_CSD_HS_TIMING, EXT_CSD_TIMING_HS,
>  			   card->ext_csd.generic_cmd6_time,
> @@ -1074,6 +1071,14 @@ static int mmc_select_hs400(struct mmc_card *card)
>  		return err;
>  	}
>  
> +	/*
> +	 * According to JEDEC v5.01 spec (6.6.5), Clock frequency should
> +	 * be set to a value not greater than 52MHz after the HS_TIMING
> +	 * field is set to 0x1.
> +	 */
> +	mmc_set_timing(card->host, MMC_TIMING_MMC_HS);
> +	mmc_set_bus_speed(card);
> +
>  	err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
>  			 EXT_CSD_BUS_WIDTH,
>  			 EXT_CSD_DDR_BUS_WIDTH_8,
> @@ -1084,6 +1089,8 @@ static int mmc_select_hs400(struct mmc_card *card)
>  		return err;
>  	}
>  
> +	mmc_set_timing(card->host, MMC_TIMING_MMC_DDR52);
> +

I didn't know why timing is set to ddr50.

Best Regards,
Jaehoon Chung

>  	err = __mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
>  			   EXT_CSD_HS_TIMING, EXT_CSD_TIMING_HS400,
>  			   card->ext_csd.generic_cmd6_time,
> 

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/