[PATCH] i2c: rk3x: fix bug that cause measured high_ns doesn't meet I2C spec

[Addy Ke]

high_ns calculated from the low division of CLKDIV register is the sum of
actual measured high_ns and rise_ns. The rise time which related to
external pull-up resistor can be up to the maximum rise time in I2C spec.

In my test, if external pull-up resistor is 4.7K, rise_ns is about 700ns.
So the actual measured high_ns is about 3900ns, which is less than 4000ns
(the minimum high_ns in I2C spec).

Signed-off-by: Addy Ke <addy.ke@xxxxxxxxxxxxxx>
---
 drivers/i2c/busses/i2c-rk3x.c | 58 +++++++++++++++++++++++++++----------------
 1 file changed, 37 insertions(+), 21 deletions(-)

diff --git a/drivers/i2c/busses/i2c-rk3x.c b/drivers/i2c/busses/i2c-rk3x.c
index e276ffb..8e1cc2b 100644
--- a/drivers/i2c/busses/i2c-rk3x.c
+++ b/drivers/i2c/busses/i2c-rk3x.c
@@ -432,9 +432,12 @@ out:
 static int rk3x_i2c_calc_divs(unsigned long i2c_rate, unsigned long scl_rate,
 			       unsigned long *div_low, unsigned long *div_high)
 {
+	unsigned long spec_min_low_ns, spec_min_high_ns;
+	unsigned long spec_max_data_hold_ns;
+	unsigned long spec_data_hold_buffer_ns;
+	unsigned long spec_max_rise_ns;
+
 	unsigned long min_low_ns, min_high_ns;
-	unsigned long max_data_hold_ns;
-	unsigned long data_hold_buffer_ns;
 	unsigned long max_low_ns, min_total_ns;
 
 	unsigned long i2c_rate_khz, scl_rate_khz;
@@ -453,30 +456,43 @@ static int rk3x_i2c_calc_divs(unsigned long i2c_rate, unsigned long scl_rate,
 	if (WARN_ON(scl_rate < 1000))
 		scl_rate = 1000;
 
+	if (scl_rate <= 100000) {
+		spec_min_low_ns = 4700;
+		spec_min_high_ns = 4000;
+		spec_max_rise_ns = 1000;
+		spec_max_data_hold_ns = 3450;
+		spec_data_hold_buffer_ns = 50;
+	} else {
+		spec_min_low_ns = 1300;
+		spec_min_high_ns = 600;
+		spec_max_rise_ns = 300;
+		spec_max_data_hold_ns = 900;
+		spec_data_hold_buffer_ns = 50;
+	}
+
 	/*
-	 * min_low_ns:  The minimum number of ns we need to hold low
-	 *		to meet i2c spec
-	 * min_high_ns: The minimum number of ns we need to hold high
-	 *		to meet i2c spec
-	 * max_low_ns:  The maximum number of ns we can hold low
-	 *		to meet i2c spec
+	 * min_low_ns:  The minimum number of ns we need to hold low.
+	 *		The fall time in RK3X's I2C controller is approximately
+	 *		equal to 0. So min_low_ns = spec_min_low_ns.
+	 * Note: low_ns should be (measured_low_ns + measured_fall_time)
+	 *	 and measured_low_ns must meet I2C spec.
 	 *
-	 * Note: max_low_ns should be (max data hold time * 2 - buffer)
+	 * min_high_ns: The minimum number of ns we need to hold high.
+	 *		The rise time which related to external pull-up resistor
+	 *		can be up to spec_max_rise_ns.
+	 *		So min_high_ns = spec_min_high_ns + spec_max_rise_ns
+	 * Note: high_ns should be (measured_high_ns + measured_rise_time)
+	 *	 and measured_high_ns must meet I2C spec.
+	 *
+	 * max_low_ns:  The maximum number of ns we can hold low.
+	 * Note: max_low_ns should be (max_data_hold_time * 2 - buffer)
 	 *	 This is because the i2c host on Rockchip holds the data line
 	 *	 for half the low time.
 	 */
-	if (scl_rate <= 100000) {
-		min_low_ns = 4700;
-		min_high_ns = 4000;
-		max_data_hold_ns = 3450;
-		data_hold_buffer_ns = 50;
-	} else {
-		min_low_ns = 1300;
-		min_high_ns = 600;
-		max_data_hold_ns = 900;
-		data_hold_buffer_ns = 50;
-	}
-	max_low_ns = max_data_hold_ns * 2 - data_hold_buffer_ns;
+	min_low_ns = spec_min_low_ns;
+	min_high_ns = spec_min_high_ns + spec_max_rise_ns;
+	max_low_ns = spec_max_data_hold_ns * 2 - spec_data_hold_buffer_ns;
+
 	min_total_ns = min_low_ns + min_high_ns;
 
 	/* Adjust to avoid overflow */
-- 
1.8.3.2


--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/