Re: [PATCH] mmc: dw_mmc: try pick the exact same voltage as vmmc for vqmmc

[Ulf Hansson]

On 11 November 2014 05:02, Addy Ke <addy.ke@xxxxxxxxxxxxxx> wrote:
> SD2.0 cards need vqmmc and vmmc to be the same.

No, that's not correct.

If I remember the spec correctly, the bus signal threshold is 0.75 * VDD.

> But vqmmc call regulator_set_voltage to set min_uv(2.7v) as far as possible.

I guess you want to do that to save as much power as possible.

> So if we set vmmc 3.3V in dt table, we will get error information as follows:
>
> [   17.785398] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req
> 50000000Hz, actual 50000000HZ div = 0)
> [   17.795175] mmc1: new high speed SDHC card at address e624
> [   17.801283] mmcblk1: mmc1:e624 SU08G 7.40 GiB
> [   17.816033]  mmcblk1: p1
> [   17.839318] mmcblk1: error -110 sending status command, retrying
> [   17.845363] mmcblk1: error -115 sending stop command, original cmd
> response 0x900, card status 0x800b00
> [   17.854758] mmcblk1: error -84 transferring data, sector 32, nr 24,
> cmd response 0x900, card status 0xb00
> [   17.864328] mmcblk1: retrying using single block read
> [   17.873647] mmcblk1: error -110 sending status command, retrying
> [   17.879660] mmcblk1: error -84 transferring data, sector 44, nr 12,
> cmd response 0x900, card status 0x0
> [   17.889051] end_request: I/O error, dev mmcblk1, sector 44
> [   17.895594] Buffer I/O error on device mmcblk1, logical block 5
> [   17.902484] mmcblk1: error -110 sending status command, retrying
> [   17.908498] mmcblk1: error -84 transferring data, sector 50, nr 6,
> cmd response 0x900, card status 0x0
> [   17.917802] end_request: I/O error, dev mmcblk1, sector 50
> [   17.924984] Buffer I/O error on device mmcblk1, logical block 6
> [   18.431258] mmc_host mmc1: Timeout sending command (cmd 0x200000 arg
> 0x0 status 0x80200000)
>
> Signed-off-by: Addy Ke <addy.ke@xxxxxxxxxxxxxx>
> ---
>  drivers/mmc/host/dw_mmc.c | 10 ++++++++--
>  1 file changed, 8 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/mmc/host/dw_mmc.c b/drivers/mmc/host/dw_mmc.c
> index b4c3044..a8b70b5 100644
> --- a/drivers/mmc/host/dw_mmc.c
> +++ b/drivers/mmc/host/dw_mmc.c
> @@ -1163,8 +1163,14 @@ static int dw_mci_switch_voltage(struct mmc_host *mmc, struct mmc_ios *ios)
>          */
>         uhs = mci_readl(host, UHS_REG);
>         if (ios->signal_voltage == MMC_SIGNAL_VOLTAGE_330) {
> -               min_uv = 2700000;
> -               max_uv = 3600000;
> +               /* try pick the exact same voltage as vmmc for vqmmc */

This seems like a generic SD protocol issue.

Should we maybe provide some helper function from the mmc core, which
in principle take the negotiated card->ocr into account while
calculating the signal voltage level. Typically min_uv should be 0.75
x (card->ocr), for these cases.

Comments?

> +               if (!IS_ERR(mmc->supply.vmmc)) {
> +                       min_uv = regulator_get_voltage(mmc->supply.vmmc);
> +                       max_uv = min_uv;
> +               } else {
> +                       min_uv = 2700000;
> +                       max_uv = 3600000;
> +               }
>                 uhs &= ~v18;
>         } else {
>                 min_uv = 1700000;
> --
> 1.8.3.2
>
>

Kind regards
Uffe
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/