[PATCH v2 04/33] thermal: exynos: remove needless triminfo_ctrl abstraction
From: Bartlomiej Zolnierkiewicz
Date: Thu Nov 13 2014 - 10:13:18 EST
reg->triminfo_ctrl[] is used in only exynos_tmu_initialize() and
accessed only if TMU_SUPPORT_TRIM_RELOAD flag is set. This flag
is set only on Exynos3250, Exynos4412 and Exynos5250 (other SoC
types don't even have triminfo_ctrl[] entries assigned in their
struct exynos_tmu_registers instances) so the register abstraction
is not needed and can be removed.
There should be no functional changes caused by this patch.
Cc: Amit Daniel Kachhap <amit.daniel@xxxxxxxxxxx>
Cc: Lukasz Majewski <l.majewski@xxxxxxxxxxx>
Cc: Eduardo Valentin <edubezval@xxxxxxxxx>
Cc: Zhang Rui <rui.zhang@xxxxxxxxx>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@xxxxxxxxxxx>
Acked-by: Kyungmin Park <kyungmin.park@xxxxxxxxxxx>
---
drivers/thermal/samsung/exynos_thermal_common.h | 1 -
drivers/thermal/samsung/exynos_tmu.c | 15 +++++++--------
drivers/thermal/samsung/exynos_tmu.h | 7 -------
drivers/thermal/samsung/exynos_tmu_data.c | 8 --------
4 files changed, 7 insertions(+), 24 deletions(-)
diff --git a/drivers/thermal/samsung/exynos_thermal_common.h b/drivers/thermal/samsung/exynos_thermal_common.h
index 158f5aa..cd44719 100644
--- a/drivers/thermal/samsung/exynos_thermal_common.h
+++ b/drivers/thermal/samsung/exynos_thermal_common.h
@@ -27,7 +27,6 @@
#define SENSOR_NAME_LEN 16
#define MAX_TRIP_COUNT 8
#define MAX_COOLING_DEVICE 4
-#define MAX_TRIMINFO_CTRL_REG 2
#define ACTIVE_INTERVAL 500
#define IDLE_INTERVAL 10000
diff --git a/drivers/thermal/samsung/exynos_tmu.c b/drivers/thermal/samsung/exynos_tmu.c
index 12e6f16..160e7fa 100644
--- a/drivers/thermal/samsung/exynos_tmu.c
+++ b/drivers/thermal/samsung/exynos_tmu.c
@@ -162,15 +162,14 @@ static int exynos_tmu_initialize(struct platform_device *pdev)
}
if (TMU_SUPPORTS(pdata, TRIM_RELOAD)) {
- for (i = 0; i < reg->triminfo_ctrl_count; i++) {
- if (pdata->triminfo_reload[i]) {
- ctrl = readl(data->base +
- reg->triminfo_ctrl[i]);
- ctrl |= pdata->triminfo_reload[i];
- writel(ctrl, data->base +
- reg->triminfo_ctrl[i]);
- }
+ if (data->soc == SOC_ARCH_EXYNOS3250) {
+ ctrl = readl(data->base + EXYNOS_TMU_TRIMINFO_CON1);
+ ctrl |= EXYNOS_TRIMINFO_RELOAD_ENABLE;
+ writel(ctrl, data->base + EXYNOS_TMU_TRIMINFO_CON1);
}
+ ctrl = readl(data->base + EXYNOS_TMU_TRIMINFO_CON2);
+ ctrl |= EXYNOS_TRIMINFO_RELOAD_ENABLE;
+ writel(ctrl, data->base + EXYNOS_TMU_TRIMINFO_CON2);
}
/* Save trimming info in order to perform calibration */
diff --git a/drivers/thermal/samsung/exynos_tmu.h b/drivers/thermal/samsung/exynos_tmu.h
index d693215..cee81a1 100644
--- a/drivers/thermal/samsung/exynos_tmu.h
+++ b/drivers/thermal/samsung/exynos_tmu.h
@@ -76,8 +76,6 @@ enum soc_type {
* struct exynos_tmu_register - register descriptors to access registers and
* bitfields. The register validity, offsets and bitfield values may vary
* slightly across different exynos SOC's.
- * @triminfo_ctrl: trim info controller register.
- * @triminfo_ctrl_count: the number of trim info controller register.
* @tmu_ctrl: TMU main controller register.
* @test_mux_addr_shift: shift bits of test mux address.
* @therm_trip_mode_shift: shift bits of tripping mode in tmu_ctrl register.
@@ -104,9 +102,6 @@ enum soc_type {
* @tmu_pmin: register to get/set the Pmin value.
*/
struct exynos_tmu_registers {
- u32 triminfo_ctrl[MAX_TRIMINFO_CTRL_REG];
- u32 triminfo_ctrl_count;
-
u32 tmu_ctrl;
u32 test_mux_addr_shift;
u32 therm_trip_mode_shift;
@@ -184,7 +179,6 @@ struct exynos_tmu_registers {
* @second_point_trim: temp value of the second point trimming
* @default_temp_offset: default temperature offset in case of no trimming
* @test_mux; information if SoC supports test MUX
- * @triminfo_reload: reload value to read TRIMINFO register
* @cal_type: calibration type for temperature
* @freq_clip_table: Table representing frequency reduction percentage.
* @freq_tab_count: Count of the above table as frequency reduction may
@@ -215,7 +209,6 @@ struct exynos_tmu_platform_data {
u8 second_point_trim;
u8 default_temp_offset;
u8 test_mux;
- u8 triminfo_reload[MAX_TRIMINFO_CTRL_REG];
enum calibration_type cal_type;
enum soc_type type;
diff --git a/drivers/thermal/samsung/exynos_tmu_data.c b/drivers/thermal/samsung/exynos_tmu_data.c
index 8153c41..d4b9a68 100644
--- a/drivers/thermal/samsung/exynos_tmu_data.c
+++ b/drivers/thermal/samsung/exynos_tmu_data.c
@@ -82,9 +82,6 @@ struct exynos_tmu_init_data const exynos4210_default_tmu_data = {
#if defined(CONFIG_SOC_EXYNOS3250)
static const struct exynos_tmu_registers exynos3250_tmu_registers = {
- .triminfo_ctrl[0] = EXYNOS_TMU_TRIMINFO_CON1,
- .triminfo_ctrl[1] = EXYNOS_TMU_TRIMINFO_CON2,
- .triminfo_ctrl_count = 2,
.tmu_ctrl = EXYNOS_TMU_REG_CONTROL,
.test_mux_addr_shift = EXYNOS4412_MUX_ADDR_SHIFT,
.therm_trip_mode_shift = EXYNOS_TMU_TRIP_MODE_SHIFT,
@@ -140,8 +137,6 @@ static const struct exynos_tmu_registers exynos3250_tmu_registers = {
.temp_level = 95, \
}, \
.freq_tab_count = 2, \
- .triminfo_reload[0] = EXYNOS_TRIMINFO_RELOAD_ENABLE, \
- .triminfo_reload[1] = EXYNOS_TRIMINFO_RELOAD_ENABLE, \
.registers = &exynos3250_tmu_registers, \
.features = (TMU_SUPPORT_EMULATION | TMU_SUPPORT_TRIM_RELOAD | \
TMU_SUPPORT_FALLING_TRIP | TMU_SUPPORT_READY_STATUS | \
@@ -163,8 +158,6 @@ struct exynos_tmu_init_data const exynos3250_default_tmu_data = {
#if defined(CONFIG_SOC_EXYNOS4412) || defined(CONFIG_SOC_EXYNOS5250)
static const struct exynos_tmu_registers exynos4412_tmu_registers = {
- .triminfo_ctrl[0] = EXYNOS_TMU_TRIMINFO_CON2,
- .triminfo_ctrl_count = 1,
.tmu_ctrl = EXYNOS_TMU_REG_CONTROL,
.test_mux_addr_shift = EXYNOS4412_MUX_ADDR_SHIFT,
.therm_trip_mode_shift = EXYNOS_TMU_TRIP_MODE_SHIFT,
@@ -221,7 +214,6 @@ static const struct exynos_tmu_registers exynos4412_tmu_registers = {
.temp_level = 95, \
}, \
.freq_tab_count = 2, \
- .triminfo_reload[0] = EXYNOS_TRIMINFO_RELOAD_ENABLE, \
.registers = &exynos4412_tmu_registers, \
.features = (TMU_SUPPORT_EMULATION | TMU_SUPPORT_TRIM_RELOAD | \
TMU_SUPPORT_FALLING_TRIP | TMU_SUPPORT_READY_STATUS | \
--
1.8.2.3
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/