[PATCH v2 1/6] GMAC: add driver for Rockchip RK3288 SoCs integrated GMAC
From: Roger Chen
Date: Wed Nov 26 2014 - 21:52:26 EST
This driver is based on stmmac driver.
modification based on Giuseppe CAVALLARO's suggestion:
1. use BIT()
> +/*RK3288_GRF_SOC_CON3*/
> +#define GMAC_TXCLK_DLY_ENABLE ((0x4000 << 16) | (0x4000))
> +#define GMAC_TXCLK_DLY_DISABLE ((0x4000 << 16) | (0x0000))
...
why do not use BIT and BIT_MASK where possible?
===>after modification:
#define GRF_BIT(nr) (BIT(nr) | BIT(nr+16))
#define GRF_CLR_BIT(nr) (BIT(nr+16))
#define GMAC_TXCLK_DLY_ENABLE GRF_BIT(14)
#define GMAC_TXCLK_DLY_DISABLE GRF_CLR_BIT(14)
...
2.
> + regmap_write(bsp_priv->grf, RK3288_GRF_SOC_CON1,
> + GMAC_PHY_INTF_SEL_RGMII);
> + regmap_write(bsp_priv->grf, RK3288_GRF_SOC_CON1,
> + GMAC_RMII_MODE_CLR);
maybe you could perform just one write unless there is some HW
constraint.
===>after modification:
regmap_write(bsp_priv->grf, RK3288_GRF_SOC_CON1,
GMAC_PHY_INTF_SEL_RGMII | GMAC_RMII_MODE_CLR);
3. use macros
> + regmap_write(bsp_priv->grf, RK3288_GRF_GPIO3D_E, 0xFFFFFFFF);
> + regmap_write(bsp_priv->grf, RK3288_GRF_GPIO4B_E,
> + 0x3<<2<<16 | 0x3<<2);
pls use macros, these shift sequence is really help to decode
===>after modification:
regmap_write(bsp_priv->grf, RK3288_GRF_GPIO4A_E, GPIO4A_12MA);
regmap_write(bsp_priv->grf, RK3288_GRF_GPIO4B_E, GPIO4B_2_12MA);
4. remove grf fail check in rk_gmac_setup()
> + if (IS_ERR(bsp_priv->grf))
> + dev_err(&pdev->dev, "Missing rockchip,grf property\n");
I wonder if you can fail on here and save all the check in
set_rgmii_speed etc.
Maybe this can be considered a mandatory property for the glue-logic.
5. remove .tx_coe=1
> +const struct stmmac_of_data rk_gmac_data = {
> + .has_gmac = 1,
> + .tx_coe = 1,
FYI, on new gmac there is the HW capability register to dinamically
provide you if coe is supported.
IMO you should add the OF "compatible" string and in case of mac
newer than the 3.50a you can remove coe.
Signed-off-by: Roger Chen <roger.chen@xxxxxxxxxxxxxx>
---
drivers/net/ethernet/stmicro/stmmac/Makefile | 2 +-
drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c | 636 ++++++++++++++++++++
.../net/ethernet/stmicro/stmmac/stmmac_platform.c | 3 +
.../net/ethernet/stmicro/stmmac/stmmac_platform.h | 1 +
4 files changed, 641 insertions(+), 1 deletion(-)
create mode 100644 drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c
diff --git a/drivers/net/ethernet/stmicro/stmmac/Makefile b/drivers/net/ethernet/stmicro/stmmac/Makefile
index ac4d562..73c2715 100644
--- a/drivers/net/ethernet/stmicro/stmmac/Makefile
+++ b/drivers/net/ethernet/stmicro/stmmac/Makefile
@@ -6,7 +6,7 @@ stmmac-objs:= stmmac_main.o stmmac_ethtool.o stmmac_mdio.o ring_mode.o \
obj-$(CONFIG_STMMAC_PLATFORM) += stmmac-platform.o
stmmac-platform-objs:= stmmac_platform.o dwmac-meson.o dwmac-sunxi.o \
- dwmac-sti.o dwmac-socfpga.o
+ dwmac-sti.o dwmac-socfpga.o dwmac-rk.o
obj-$(CONFIG_STMMAC_PCI) += stmmac-pci.o
stmmac-pci-objs:= stmmac_pci.o
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c
new file mode 100644
index 0000000..870563f
--- /dev/null
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c
@@ -0,0 +1,636 @@
+/**
+ * dwmac-rk.c - Rockchip RK3288 DWMAC specific glue layer
+ *
+ * Copyright (C) 2014 Chen-Zhi (Roger Chen)
+ *
+ * Chen-Zhi (Roger Chen) <roger.chen@xxxxxxxxxxxxxx>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/stmmac.h>
+#include <linux/bitops.h>
+#include <linux/clk.h>
+#include <linux/phy.h>
+#include <linux/of_net.h>
+#include <linux/gpio.h>
+#include <linux/of_gpio.h>
+#include <linux/of_device.h>
+#include <linux/regulator/consumer.h>
+#include <linux/delay.h>
+#include <linux/mfd/syscon.h>
+#include <linux/regmap.h>
+
+struct rk_priv_data {
+ struct platform_device *pdev;
+ int phy_iface;
+ bool power_ctrl_by_pmu;
+ char pmu_regulator[32];
+ int pmu_enable_level;
+
+ int power_io;
+ int power_io_level;
+ int reset_io;
+ int reset_io_level;
+ int phyirq_io;
+ int phyirq_io_level;
+
+ bool clk_enabled;
+ bool clock_input;
+
+ struct clk *clk_mac;
+ struct clk *clk_mac_pll;
+ struct clk *gmac_clkin;
+ struct clk *mac_clk_rx;
+ struct clk *mac_clk_tx;
+ struct clk *clk_mac_ref;
+ struct clk *clk_mac_refout;
+ struct clk *aclk_mac;
+ struct clk *pclk_mac;
+
+ int tx_delay;
+ int rx_delay;
+
+ struct regmap *grf;
+};
+
+#define RK3288_GRF_SOC_CON1 0x0248
+#define RK3288_GRF_SOC_CON3 0x0250
+#define RK3288_GRF_GPIO3D_E 0x01ec
+#define RK3288_GRF_GPIO4A_E 0x01f0
+#define RK3288_GRF_GPIO4B_E 0x01f4
+
+#define GPIO3D_2MA 0xFFFF0000
+#define GPIO3D_4MA 0xFFFF5555
+#define GPIO3D_8MA 0xFFFFAAAA
+#define GPIO3D_12MA 0xFFFFFFFF
+
+#define GPIO4A_2MA 0xFFFF0000
+#define GPIO4A_4MA 0xFFFF5555
+#define GPIO4A_8MA 0xFFFFAAAA
+#define GPIO4A_12MA 0xFFFFFFFF
+
+#define GRF_BIT(nr) (BIT(nr) | BIT(nr+16))
+#define GRF_CLR_BIT(nr) (BIT(nr+16))
+
+#define GPIO4B_2_2MA (GRF_CLR_BIT(2) | GRF_CLR_BIT(3))
+#define GPIO4B_2_4MA (GRF_BIT(2) | GRF_CLR_BIT(3))
+#define GPIO4B_2_8MA (GRF_CLR_BIT(2) | GRF_BIT(3))
+#define GPIO4B_2_12MA (GRF_BIT(2) | GRF_BIT(3))
+
+/*RK3288_GRF_SOC_CON1*/
+#define GMAC_PHY_INTF_SEL_RGMII (GRF_BIT(6) | GRF_CLR_BIT(7) | GRF_CLR_BIT(8))
+#define GMAC_PHY_INTF_SEL_RMII (GRF_CLR_BIT(6) | GRF_CLR_BIT(7) | GRF_BIT(8))
+#define GMAC_FLOW_CTRL GRF_BIT(9)
+#define GMAC_FLOW_CTRL_CLR GRF_CLR_BIT(9)
+#define GMAC_SPEED_10M GRF_CLR_BIT(10)
+#define GMAC_SPEED_100M GRF_BIT(10)
+#define GMAC_RMII_CLK_25M GRF_BIT(11)
+#define GMAC_RMII_CLK_2_5M GRF_CLR_BIT(11)
+#define GMAC_CLK_125M (GRF_CLR_BIT(12) | GRF_CLR_BIT(13))
+#define GMAC_CLK_25M (GRF_BIT(12) | GRF_BIT(13))
+#define GMAC_CLK_2_5M (GRF_CLR_BIT(12) | GRF_BIT(13))
+#define GMAC_RMII_MODE GRF_BIT(14)
+#define GMAC_RMII_MODE_CLR GRF_CLR_BIT(14)
+
+/*RK3288_GRF_SOC_CON3*/
+#define GMAC_TXCLK_DLY_ENABLE GRF_BIT(14)
+#define GMAC_TXCLK_DLY_DISABLE GRF_CLR_BIT(14)
+#define GMAC_RXCLK_DLY_ENABLE GRF_BIT(15)
+#define GMAC_RXCLK_DLY_DISABLE GRF_CLR_BIT(15)
+#define GMAC_CLK_RX_DL_CFG(val) ((0x7F<<7<<16) | (val<<7))
+#define GMAC_CLK_TX_DL_CFG(val) ((0x7F<<16) | (val))
+
+static void set_to_rgmii(struct rk_priv_data *bsp_priv,
+ int tx_delay, int rx_delay)
+{
+ if (IS_ERR(bsp_priv->grf)) {
+ pr_err("%s: Missing rockchip,grf property\n", __func__);
+ return;
+ }
+
+ regmap_write(bsp_priv->grf, RK3288_GRF_SOC_CON1,
+ GMAC_PHY_INTF_SEL_RGMII | GMAC_RMII_MODE_CLR);
+ regmap_write(bsp_priv->grf, RK3288_GRF_SOC_CON3,
+ GMAC_RXCLK_DLY_ENABLE | GMAC_TXCLK_DLY_ENABLE |
+ GMAC_CLK_RX_DL_CFG(rx_delay) |
+ GMAC_CLK_TX_DL_CFG(tx_delay));
+ regmap_write(bsp_priv->grf, RK3288_GRF_GPIO3D_E, GPIO3D_12MA);
+ regmap_write(bsp_priv->grf, RK3288_GRF_GPIO4A_E, GPIO4A_12MA);
+ regmap_write(bsp_priv->grf, RK3288_GRF_GPIO4B_E, GPIO4B_2_12MA);
+
+ pr_debug("%s: tx delay=0x%x; rx delay=0x%x;\n",
+ __func__, tx_delay, rx_delay);
+}
+
+static void set_to_rmii(struct rk_priv_data *bsp_priv)
+{
+ if (IS_ERR(bsp_priv->grf)) {
+ pr_err("%s: Missing rockchip,grf property\n", __func__);
+ return;
+ }
+
+ regmap_write(bsp_priv->grf, RK3288_GRF_SOC_CON1,
+ GMAC_PHY_INTF_SEL_RMII);
+ regmap_write(bsp_priv->grf, RK3288_GRF_SOC_CON1,
+ GMAC_RMII_MODE);
+}
+
+static void set_rgmii_speed(struct rk_priv_data *bsp_priv, int speed)
+{
+ if (IS_ERR(bsp_priv->grf)) {
+ pr_err("%s: Missing rockchip,grf property\n", __func__);
+ return;
+ }
+
+ if (speed == 10)
+ regmap_write(bsp_priv->grf, RK3288_GRF_SOC_CON1, GMAC_CLK_2_5M);
+ else if (speed == 100)
+ regmap_write(bsp_priv->grf, RK3288_GRF_SOC_CON1, GMAC_CLK_25M);
+ else if (speed == 1000)
+ regmap_write(bsp_priv->grf, RK3288_GRF_SOC_CON1, GMAC_CLK_125M);
+ else
+ pr_err("unknown speed value for RGMII! speed=%d", speed);
+}
+
+static void set_rmii_speed(struct rk_priv_data *bsp_priv, int speed)
+{
+ if (IS_ERR(bsp_priv->grf)) {
+ pr_err("%s: Missing rockchip,grf property\n", __func__);
+ return;
+ }
+
+ if (speed == 10) {
+ regmap_write(bsp_priv->grf, RK3288_GRF_SOC_CON1,
+ GMAC_RMII_CLK_2_5M);
+ regmap_write(bsp_priv->grf, RK3288_GRF_SOC_CON1,
+ GMAC_SPEED_10M);
+ } else if (speed == 100) {
+ regmap_write(bsp_priv->grf, RK3288_GRF_SOC_CON1,
+ GMAC_RMII_CLK_25M);
+ regmap_write(bsp_priv->grf, RK3288_GRF_SOC_CON1,
+ GMAC_SPEED_100M);
+ } else {
+ pr_err("unknown speed value for RMII! speed=%d", speed);
+ }
+}
+
+#define MAC_CLK_RX "mac_clk_rx"
+#define MAC_CLK_TX "mac_clk_tx"
+#define CLK_MAC_REF "clk_mac_ref"
+#define CLK_MAC_REF_OUT "clk_mac_refout"
+#define CLK_MAC_PLL "clk_mac_pll"
+#define ACLK_MAC "aclk_mac"
+#define PCLK_MAC "pclk_mac"
+#define MAC_CLKIN "ext_gmac"
+#define CLK_MAC "stmmaceth"
+
+static int gmac_clk_init(struct rk_priv_data *bsp_priv)
+{
+ struct device *dev = &bsp_priv->pdev->dev;
+
+ bsp_priv->clk_enabled = false;
+
+ bsp_priv->mac_clk_rx = clk_get(dev, MAC_CLK_RX);
+ if (IS_ERR(bsp_priv->mac_clk_rx))
+ pr_warn("%s: warning: cannot get clock %s\n",
+ __func__, MAC_CLK_RX);
+
+ bsp_priv->mac_clk_tx = clk_get(dev, MAC_CLK_TX);
+ if (IS_ERR(bsp_priv->mac_clk_tx))
+ pr_warn("%s: warning: cannot get clock %s\n",
+ __func__, MAC_CLK_TX);
+
+ bsp_priv->clk_mac_ref = clk_get(dev, CLK_MAC_REF);
+ if (IS_ERR(bsp_priv->clk_mac_ref))
+ pr_warn("%s: warning: cannot get clock %s\n",
+ __func__, CLK_MAC_REF);
+
+ bsp_priv->clk_mac_refout = clk_get(dev, CLK_MAC_REF_OUT);
+ if (IS_ERR(bsp_priv->clk_mac_refout))
+ pr_warn("%s: warning:cannot get clock %s\n",
+ __func__, CLK_MAC_REF_OUT);
+
+ bsp_priv->aclk_mac = clk_get(dev, ACLK_MAC);
+ if (IS_ERR(bsp_priv->aclk_mac))
+ pr_warn("%s: warning: cannot get clock %s\n",
+ __func__, ACLK_MAC);
+
+ bsp_priv->pclk_mac = clk_get(dev, PCLK_MAC);
+ if (IS_ERR(bsp_priv->pclk_mac))
+ pr_warn("%s: warning: cannot get clock %s\n",
+ __func__, PCLK_MAC);
+
+ bsp_priv->clk_mac_pll = clk_get(dev, CLK_MAC_PLL);
+ if (IS_ERR(bsp_priv->clk_mac_pll))
+ pr_warn("%s: warning: cannot get clock %s\n",
+ __func__, CLK_MAC_PLL);
+
+ bsp_priv->gmac_clkin = clk_get(dev, MAC_CLKIN);
+ if (IS_ERR(bsp_priv->gmac_clkin))
+ pr_warn("%s: warning: cannot get clock %s\n",
+ __func__, MAC_CLKIN);
+
+ bsp_priv->clk_mac = clk_get(dev, CLK_MAC);
+ if (IS_ERR(bsp_priv->clk_mac))
+ pr_warn("%s: warning: cannot get clock %s\n",
+ __func__, CLK_MAC);
+
+ if (bsp_priv->clock_input) {
+ pr_info("%s: clock input from PHY\n", __func__);
+ } else {
+ if (bsp_priv->phy_iface == PHY_INTERFACE_MODE_RMII)
+ clk_set_rate(bsp_priv->clk_mac_pll, 50000000);
+
+ clk_set_parent(bsp_priv->clk_mac, bsp_priv->clk_mac_pll);
+ }
+
+ return 0;
+}
+
+static int gmac_clk_enable(struct rk_priv_data *bsp_priv, bool enable)
+{
+ int phy_iface = phy_iface = bsp_priv->phy_iface;
+
+ if (enable) {
+ if (!bsp_priv->clk_enabled) {
+ if (phy_iface == PHY_INTERFACE_MODE_RMII) {
+ if (!IS_ERR(bsp_priv->mac_clk_rx))
+ clk_prepare_enable(
+ bsp_priv->mac_clk_rx);
+
+ if (!IS_ERR(bsp_priv->clk_mac_ref))
+ clk_prepare_enable(
+ bsp_priv->clk_mac_ref);
+
+ if (!IS_ERR(bsp_priv->clk_mac_refout))
+ clk_prepare_enable(
+ bsp_priv->clk_mac_refout);
+ }
+
+ if (!IS_ERR(bsp_priv->aclk_mac))
+ clk_prepare_enable(bsp_priv->aclk_mac);
+
+ if (!IS_ERR(bsp_priv->pclk_mac))
+ clk_prepare_enable(bsp_priv->pclk_mac);
+
+ if (!IS_ERR(bsp_priv->mac_clk_tx))
+ clk_prepare_enable(bsp_priv->mac_clk_tx);
+
+ /**
+ * if (!IS_ERR(bsp_priv->clk_mac))
+ * clk_prepare_enable(bsp_priv->clk_mac);
+ */
+ mdelay(5);
+ bsp_priv->clk_enabled = true;
+ }
+ } else {
+ if (bsp_priv->clk_enabled) {
+ if (phy_iface == PHY_INTERFACE_MODE_RMII) {
+ if (!IS_ERR(bsp_priv->mac_clk_rx))
+ clk_disable_unprepare(
+ bsp_priv->mac_clk_rx);
+
+ if (!IS_ERR(bsp_priv->clk_mac_ref))
+ clk_disable_unprepare(
+ bsp_priv->clk_mac_ref);
+
+ if (!IS_ERR(bsp_priv->clk_mac_refout))
+ clk_disable_unprepare(
+ bsp_priv->clk_mac_refout);
+ }
+
+ if (!IS_ERR(bsp_priv->aclk_mac))
+ clk_disable_unprepare(bsp_priv->aclk_mac);
+
+ if (!IS_ERR(bsp_priv->pclk_mac))
+ clk_disable_unprepare(bsp_priv->pclk_mac);
+
+ if (!IS_ERR(bsp_priv->mac_clk_tx))
+ clk_disable_unprepare(bsp_priv->mac_clk_tx);
+ /**
+ * if (!IS_ERR(bsp_priv->clk_mac))
+ * clk_disable_unprepare(bsp_priv->clk_mac);
+ */
+ bsp_priv->clk_enabled = false;
+ }
+ }
+
+ return 0;
+}
+
+static int power_on_by_pmu(struct rk_priv_data *bsp_priv, bool enable)
+{
+ struct regulator *ldo;
+ char *ldostr = bsp_priv->pmu_regulator;
+ int ret;
+
+ if (!ldostr) {
+ pr_err("%s: no ldo found\n", __func__);
+ return -1;
+ }
+
+ ldo = regulator_get(NULL, ldostr);
+ if (!ldo) {
+ pr_err("\n%s get ldo %s failed\n", __func__, ldostr);
+ } else {
+ if (enable) {
+ if (!regulator_is_enabled(ldo)) {
+ regulator_set_voltage(ldo, 3300000, 3300000);
+ ret = regulator_enable(ldo);
+ if (ret != 0)
+ pr_err("%s: fail to enable %s\n",
+ __func__, ldostr);
+ else
+ pr_info("turn on ldo done.\n");
+ } else {
+ pr_warn("%s is enabled before enable", ldostr);
+ }
+ } else {
+ if (regulator_is_enabled(ldo)) {
+ ret = regulator_disable(ldo);
+ if (ret != 0)
+ pr_err("%s: fail to disable %s\n",
+ __func__, ldostr);
+ else
+ pr_info("turn off ldo done.\n");
+ } else {
+ pr_warn("%s is disabled before disable",
+ ldostr);
+ }
+ }
+ regulator_put(ldo);
+ }
+
+ return 0;
+}
+
+static int power_on_by_gpio(struct rk_priv_data *bsp_priv, bool enable)
+{
+ if (enable) {
+ /*power on*/
+ if (gpio_is_valid(bsp_priv->power_io))
+ gpio_direction_output(bsp_priv->power_io,
+ bsp_priv->power_io_level);
+ } else {
+ /*power off*/
+ if (gpio_is_valid(bsp_priv->power_io))
+ gpio_direction_output(bsp_priv->power_io,
+ !bsp_priv->power_io_level);
+ }
+
+ return 0;
+}
+
+static int phy_power_on(struct rk_priv_data *bsp_priv, bool enable)
+{
+ int ret = -1;
+
+ pr_info("Ethernet PHY power %s\n", enable == 1 ? "on" : "off");
+
+ if (bsp_priv->power_ctrl_by_pmu)
+ ret = power_on_by_pmu(bsp_priv, enable);
+ else
+ ret = power_on_by_gpio(bsp_priv, enable);
+
+ if (enable) {
+ /*reset*/
+ if (gpio_is_valid(bsp_priv->reset_io)) {
+ gpio_direction_output(bsp_priv->reset_io,
+ bsp_priv->reset_io_level);
+ mdelay(5);
+ gpio_direction_output(bsp_priv->reset_io,
+ !bsp_priv->reset_io_level);
+ }
+ mdelay(30);
+
+ } else {
+ /*pull down reset*/
+ if (gpio_is_valid(bsp_priv->reset_io)) {
+ gpio_direction_output(bsp_priv->reset_io,
+ bsp_priv->reset_io_level);
+ }
+ }
+
+ return ret;
+}
+
+#define GPIO_PHY_POWER "gmac_phy_power"
+#define GPIO_PHY_RESET "gmac_phy_reset"
+#define GPIO_PHY_IRQ "gmac_phy_irq"
+
+static void *rk_gmac_setup(struct platform_device *pdev)
+{
+ struct rk_priv_data *bsp_priv;
+ struct device *dev = &pdev->dev;
+ enum of_gpio_flags flags;
+ int ret;
+ const char *strings = NULL;
+ int value;
+ int irq;
+
+ bsp_priv = devm_kzalloc(dev, sizeof(*bsp_priv), GFP_KERNEL);
+ if (!bsp_priv)
+ return ERR_PTR(-ENOMEM);
+
+ bsp_priv->phy_iface = of_get_phy_mode(dev->of_node);
+
+ ret = of_property_read_string(dev->of_node, "pmu_regulator", &strings);
+ if (ret) {
+ pr_err("%s: Can not read property: pmu_regulator.\n", __func__);
+ bsp_priv->power_ctrl_by_pmu = false;
+ } else {
+ pr_info("%s: ethernet phy power controlled by pmu(%s).\n",
+ __func__, strings);
+ bsp_priv->power_ctrl_by_pmu = true;
+ strcpy(bsp_priv->pmu_regulator, strings);
+ }
+
+ ret = of_property_read_u32(dev->of_node, "pmu_enable_level", &value);
+ if (ret) {
+ pr_err("%s: Can not read property: pmu_enable_level.\n",
+ __func__);
+ bsp_priv->power_ctrl_by_pmu = false;
+ } else {
+ pr_info("%s: PHY power controlled by pmu(level = %s).\n",
+ __func__, (value == 1) ? "HIGH" : "LOW");
+ bsp_priv->power_ctrl_by_pmu = true;
+ bsp_priv->pmu_enable_level = value;
+ }
+
+ ret = of_property_read_string(dev->of_node, "clock_in_out", &strings);
+ if (ret) {
+ pr_err("%s: Can not read property: clock_in_out.\n", __func__);
+ bsp_priv->clock_input = true;
+ } else {
+ pr_info("%s: clock input or output? (%s).\n",
+ __func__, strings);
+ if (!strcmp(strings, "input"))
+ bsp_priv->clock_input = true;
+ else
+ bsp_priv->clock_input = false;
+ }
+
+ ret = of_property_read_u32(dev->of_node, "tx_delay", &value);
+ if (ret) {
+ bsp_priv->tx_delay = 0x30;
+ pr_err("%s: Can not read property: tx_delay.", __func__);
+ pr_err("%s: set tx_delay to 0x%x\n",
+ __func__, bsp_priv->tx_delay);
+ } else {
+ pr_info("%s: TX delay(0x%x).\n", __func__, value);
+ bsp_priv->tx_delay = value;
+ }
+
+ ret = of_property_read_u32(dev->of_node, "rx_delay", &value);
+ if (ret) {
+ bsp_priv->rx_delay = 0x10;
+ pr_err("%s: Can not read property: rx_delay.", __func__);
+ pr_err("%s: set rx_delay to 0x%x\n",
+ __func__, bsp_priv->rx_delay);
+ } else {
+ pr_info("%s: RX delay(0x%x).\n", __func__, value);
+ bsp_priv->rx_delay = value;
+ }
+
+ bsp_priv->grf = syscon_regmap_lookup_by_phandle(dev->of_node,
+ "rockchip,grf");
+ bsp_priv->phyirq_io =
+ of_get_named_gpio_flags(dev->of_node,
+ "phyirq-gpio", 0, &flags);
+ bsp_priv->phyirq_io_level = (flags & OF_GPIO_ACTIVE_LOW) ? 0 : 1;
+
+ bsp_priv->reset_io =
+ of_get_named_gpio_flags(dev->of_node,
+ "reset-gpio", 0, &flags);
+ bsp_priv->reset_io_level = (flags & OF_GPIO_ACTIVE_LOW) ? 0 : 1;
+
+ bsp_priv->power_io =
+ of_get_named_gpio_flags(dev->of_node, "power-gpio", 0, &flags);
+ bsp_priv->power_io_level = (flags & OF_GPIO_ACTIVE_LOW) ? 0 : 1;
+
+ /*power*/
+ if (!gpio_is_valid(bsp_priv->power_io)) {
+ pr_err("%s: Failed to get GPIO %s.\n",
+ __func__, "power-gpio");
+ } else {
+ ret = gpio_request(bsp_priv->power_io, GPIO_PHY_POWER);
+ if (ret)
+ pr_err("%s: ERROR: Failed to request GPIO %s.\n",
+ __func__, GPIO_PHY_POWER);
+ }
+
+ if (!gpio_is_valid(bsp_priv->reset_io)) {
+ pr_err("%s: ERROR: Get reset-gpio failed.\n", __func__);
+ } else {
+ ret = gpio_request(bsp_priv->reset_io, GPIO_PHY_RESET);
+ if (ret)
+ pr_err("%s: ERROR: Failed to request GPIO %s.\n",
+ __func__, GPIO_PHY_RESET);
+ }
+
+ if (bsp_priv->phyirq_io > 0) {
+ struct plat_stmmacenet_data *plat_dat;
+
+ pr_info("PHY irq in use\n");
+ ret = gpio_request(bsp_priv->phyirq_io, GPIO_PHY_IRQ);
+ if (ret < 0) {
+ pr_warn("%s: Failed to request GPIO %s\n",
+ __func__, GPIO_PHY_IRQ);
+ goto goon;
+ }
+
+ ret = gpio_direction_input(bsp_priv->phyirq_io);
+ if (ret < 0) {
+ pr_err("%s, Failed to set input for GPIO %s\n",
+ __func__, GPIO_PHY_IRQ);
+ gpio_free(bsp_priv->phyirq_io);
+ goto goon;
+ }
+
+ irq = gpio_to_irq(bsp_priv->phyirq_io);
+ if (irq < 0) {
+ ret = irq;
+ pr_err("Failed to set irq for %s\n",
+ GPIO_PHY_IRQ);
+ gpio_free(bsp_priv->phyirq_io);
+ goto goon;
+ }
+
+ plat_dat = dev_get_platdata(&pdev->dev);
+ if (plat_dat)
+ plat_dat->mdio_bus_data->probed_phy_irq = irq;
+ else
+ pr_err("%s: plat_data is NULL\n", __func__);
+ }
+
+goon:
+ /*rmii or rgmii*/
+ if (bsp_priv->phy_iface == PHY_INTERFACE_MODE_RGMII) {
+ pr_info("%s: init for RGMII\n", __func__);
+ set_to_rgmii(bsp_priv, bsp_priv->tx_delay, bsp_priv->rx_delay);
+ } else if (bsp_priv->phy_iface == PHY_INTERFACE_MODE_RMII) {
+ pr_info("%s: init for RMII\n", __func__);
+ set_to_rmii(bsp_priv);
+ } else {
+ pr_err("%s: ERROR: NO interface defined!\n", __func__);
+ }
+
+ bsp_priv->pdev = pdev;
+
+ gmac_clk_init(bsp_priv);
+
+ return bsp_priv;
+}
+
+static int rk_gmac_init(struct platform_device *pdev, void *priv)
+{
+ struct rk_priv_data *bsp_priv = priv;
+ int ret;
+
+ ret = phy_power_on(bsp_priv, true);
+ if (ret)
+ return ret;
+
+ ret = gmac_clk_enable(bsp_priv, true);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static void rk_gmac_exit(struct platform_device *pdev, void *priv)
+{
+ struct rk_priv_data *gmac = priv;
+
+ phy_power_on(gmac, false);
+ gmac_clk_enable(gmac, false);
+}
+
+static void rk_fix_speed(void *priv, unsigned int speed)
+{
+ struct rk_priv_data *bsp_priv = priv;
+
+ if (bsp_priv->phy_iface == PHY_INTERFACE_MODE_RGMII)
+ set_rgmii_speed(bsp_priv, speed);
+ else if (bsp_priv->phy_iface == PHY_INTERFACE_MODE_RMII)
+ set_rmii_speed(bsp_priv, speed);
+ else
+ pr_err("unsupported interface %d", bsp_priv->phy_iface);
+}
+
+const struct stmmac_of_data rk_gmac_data = {
+ .has_gmac = 1,
+ .fix_mac_speed = rk_fix_speed,
+ .setup = rk_gmac_setup,
+ .init = rk_gmac_init,
+ .exit = rk_gmac_exit,
+};
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
index 15814b7..b4dee96 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
@@ -33,6 +33,7 @@
static const struct of_device_id stmmac_dt_ids[] = {
/* SoC specific glue layers should come before generic bindings */
+ { .compatible = "rockchip,rk3288-gmac", .data = &rk_gmac_data},
{ .compatible = "amlogic,meson6-dwmac", .data = &meson6_dwmac_data},
{ .compatible = "allwinner,sun7i-a20-gmac", .data = &sun7i_gmac_data},
{ .compatible = "st,stih415-dwmac", .data = &stih4xx_dwmac_data},
@@ -291,6 +292,8 @@ static int stmmac_pltfr_probe(struct platform_device *pdev)
return -ENOMEM;
}
+ pdev->dev.platform_data = plat_dat;
+
ret = stmmac_probe_config_dt(pdev, plat_dat, &mac);
if (ret) {
pr_err("%s: main dt probe failed", __func__);
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.h b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.h
index 25dd1f7..32a0516 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.h
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.h
@@ -24,5 +24,6 @@ extern const struct stmmac_of_data sun7i_gmac_data;
extern const struct stmmac_of_data stih4xx_dwmac_data;
extern const struct stmmac_of_data stid127_dwmac_data;
extern const struct stmmac_of_data socfpga_gmac_data;
+extern const struct stmmac_of_data rk_gmac_data;
#endif /* __STMMAC_PLATFORM_H__ */
--
1.7.9.5
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/