[PATCH/RFC v8 11/14] DT: Add documentation for the mfd Maxim max77693

[Jacek Anaszewski]

This patch adds device tree binding documentation for
the flash cell of the Maxim max77693 multifunctional device.

Signed-off-by: Jacek Anaszewski <j.anaszewski@xxxxxxxxxxx>
Signed-off-by: Andrzej Hajda <a.hajda@xxxxxxxxxxx>
Acked-by: Kyungmin Park <kyungmin.park@xxxxxxxxxxx>
Cc: Lee Jones <lee.jones@xxxxxxxxxx>
Cc: SangYoung Son <hello.son@xxxxxxxxxxx>
Cc: Samuel Ortiz <sameo@xxxxxxxxxxxxxxx>
Cc: Bryan Wu <cooloney@xxxxxxxxx>
Cc: Richard Purdie <rpurdie@xxxxxxxxx>
Cc: Rob Herring <robh+dt@xxxxxxxxxx>
Cc: Pawel Moll <pawel.moll@xxxxxxx>
Cc: Mark Rutland <mark.rutland@xxxxxxx>
Cc: Ian Campbell <ijc+devicetree@xxxxxxxxxxxxxx>
Cc: Kumar Gala <galak@xxxxxxxxxxxxxx>
Cc: <devicetree@xxxxxxxxxxxxxxx>
---
 Documentation/devicetree/bindings/mfd/max77693.txt |   74 ++++++++++++++++++++
 1 file changed, 74 insertions(+)

diff --git a/Documentation/devicetree/bindings/mfd/max77693.txt b/Documentation/devicetree/bindings/mfd/max77693.txt
index 01e9f30..50a8dad 100644
--- a/Documentation/devicetree/bindings/mfd/max77693.txt
+++ b/Documentation/devicetree/bindings/mfd/max77693.txt
@@ -41,6 +41,62 @@ Optional properties:
 	 To get more informations, please refer to documentaion.
 	[*] refer Documentation/devicetree/bindings/pwm/pwm.txt
 
+- led-flash : the LED submodule device node
+
+There are two led outputs available - fled1 and fled2. Each of them can
+control a separate led or they can be connected together to double
+the maximum current for a single connected led. One led is represented
+by one child node.
+
+Required properties:
+- compatible : must be "maxim,max77693-flash"
+
+Optional properties:
+- maxim,fleds : array of current outputs in order: fled1, fled2
+	Note: both current outputs can be connected to a single led
+	Possible values:
+		0 - the output is left disconnected,
+		1 - a diode is connected to the output.
+- maxim,trigger-type : Array of trigger types in order: flash, torch
+	Possible trigger types:
+		0 - Rising edge of the signal triggers the flash/torch,
+		1 - Signal level controls duration of the flash/torch.
+- maxim,trigger : Array of flags indicating which trigger can activate given led
+	in order: fled1, fled2
+	Possible flag values (can be combined):
+		1 - FLASH pin of the chip,
+		2 - TORCH pin of the chip,
+		4 - software via I2C command.
+- maxim,boost-mode :
+	In boost mode the device can produce up to 1.2A of total current
+	on both outputs. The maximum current on each output is reduced
+	to 625mA then. If there are two child led nodes defined then boost
+	is enabled by default.
+	Possible values:
+		0 - no boost,
+		1 - adaptive mode,
+		2 - fixed mode.
+- maxim,boost-vout : Output voltage of the boost module in millivolts.
+- maxim,vsys-min : Low input voltage level in millivolts. Flash is not fired
+	if chip estimates that system voltage could drop below this level due
+	to flash power consumption.
+
+A child node must be defined per sub-led.
+
+Required properties of the LED child node:
+- label : see Documentation/devicetree/bindings/leds/common.txt
+- maxim,fled_id : identifier of the fled output the led is connected to:
+		1 - FLED1,
+		2 - FLED2.
+
+Optional properties of the LED child node:
+- max-microamp : see Documentation/devicetree/bindings/leds/common.txt
+		Range: 15625 - 250000
+- flash-max-microamp : see Documentation/devicetree/bindings/leds/common.txt
+		Range: 15625 - 1000000
+- flash-timeout-microsec : see Documentation/devicetree/bindings/leds/common.txt
+		Range: 62500 - 1000000
+
 Example:
 	max77693@66 {
 		compatible = "maxim,max77693";
@@ -73,4 +129,22 @@ Example:
 			pwms = <&pwm 0 40000 0>;
 			pwm-names = "haptic";
 		};
+
+		led_flash: led-flash {
+			compatible = "maxim,max77693-flash";
+			maxim,fleds = <1 0>;
+			maxim,trigger = <7 0>;
+			maxim,trigger-type = <0 1>;
+			maxim,boost-mode = <0>;
+			maxim,boost-vout = <5000>;
+			maxim,vsys-min = <2400>;
+
+			camera-flash {
+				maxim,fled_id = <1>
+				label = "max77693-flash";
+				max-microamp = <250000>;
+				flash-max-microamp = <1000000>;
+				flash-timeout-microsec = <1000000>;
+			}
+		};
 	};
-- 
1.7.9.5

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/