Re: [PATCH 2/2] ARM: dts: kirkwood: add dts support for Seagate BlackArmor NAS220

From: Andrew Lunn
Date: Tue Dec 16 2014 - 03:58:00 EST

On Mon, Dec 15, 2014 at 09:38:55PM +0100, Evgeni Dobrev wrote:
> This patch adds support for Seagate BlackArmor NAS220.

Hi Evgeni

Thanks for the patch. It looks good apart from a few minor comments.

Please could you also Cc: the mvebu maintainers, otherwise you patch
might net be seen by the right people. I added them.

>
> The Seagate BlackArmor NAS 220 is a NAS system based on Marvell 88f6192. It has 32MB NAND and 128MB DRAM. It has two SATA slots, one Gigabit Ethernet port, two USB 2.0 ports, two buttons and three LEDs. There is a serial port available on the CN5 connector on the board (1 - TX, 4 - RX, 6 - GND).
>

> The only functionality still not implemented is the bi-color led on
> the front panel (status). Pins mpp22 and mpp23 control this
> led. Setting mpp22 to high and mpp23 to low results in orange
> color. Setting mpp22 to low and mpp23 to high results in blue color.

Any thoughts how you are going to handle this? Can you have both blue
and orange at the same time be setting both high? Or are both then
off?

> The third led is wired to show the SATA activity on the two drives.
>
> Signed-off-by: Evgeni Dobrev <evgeni@xxxxxxxxxxxxxxxx>
> ---
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/kirkwood-nas220.dts | 182 +++++++++++++++++++++++++++++++++
> 2 files changed, 183 insertions(+)
> create mode 100644 arch/arm/boot/dts/kirkwood-nas220.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 38c89ca..8b9ad1d 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -132,6 +132,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += kirkwood-b3.dtb \
> kirkwood-lsxhl.dtb \
> kirkwood-mplcec4.dtb \
> kirkwood-mv88f6281gtw-ge.dtb \
> + kirkwood-nas220.dtb \
> kirkwood-net2big.dtb \
> kirkwood-net5big.dtb \
> kirkwood-netgear_readynas_duo_v2.dtb \
> diff --git a/arch/arm/boot/dts/kirkwood-nas220.dts b/arch/arm/boot/dts/kirkwood-nas220.dts
> new file mode 100644
> index 0000000..1de2ac3
> --- /dev/null
> +++ b/arch/arm/boot/dts/kirkwood-nas220.dts
> @@ -0,0 +1,182 @@
> +/*
> + * Device Tree file for Seagate BlackArmor NAS220
> + *
> + * Copyright (C) 2014 Evgeni Dobrev <evgeni@xxxxxxxxxxxxxxxx>
> + *
> + * Licensed under GPLv2 or later.
> + */

Gregory is in the process of changing the license for the Marvell
Armada SoCs. He is adding X11 license as well, so making it easier for
other systems to reuse the DT blob. I want to see how easy it goes
with Armada, but we may also do the same for Kirkwood sometime in the
future. So maybe you can think about this and follow the discussion.

> +
> +/dts-v1/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include "kirkwood.dtsi"
> +#include "kirkwood-6192.dtsi"
> +
> +/ {
> + model = "Seagate NAS 220";
> + compatible = "seagate,nas220", "marvell,kirkwood-88f6192", "marvell,kirkwood";
> +
> + memory { /* 128 MB */
> + device_type = "memory";
> + reg = <0x00000000 0x8000000>;
> + };
> +
> + chosen {
> + bootargs = "console=ttyS0,115200n8";
> + stdout-path = &uart0;
> + };

It looks like there is a mix of spaces and tabs. Please only use tabs
in this file.

> +
> + ocp@f1000000 {
> + pinctrl: pin-controller@10000 {
> + pinctrl-0 = < &pmx_uart0
> + &pmx_button_reset
> + &pmx_button_power
> + >;
> + pinctrl-names = "default";
> +
> + pmx_act_sata0: pmx-act-sata0 {
> + marvell,pins = "mpp15";
> + marvell,function = "sata0";
> + };
> + pmx_act_sata1: pmx-act-sata1 {
> + marvell,pins = "mpp16";
> + marvell,function = "sata1";
> + };
> + pmx_power_sata0: pmx-power-sata0 {
> + marvell,pins = "mpp24";
> + marvell,function = "gpio";
> + };
> + pmx_power_sata1: pmx-power-sata1 {
> + marvell,pins = "mpp28";
> + marvell,function = "gpio";
> + };
> + pmx_button_reset: pmx-button-reset {
> + marvell,pins = "mpp29";
> + marvell,function = "gpio";
> + };
> + pmx_button_power: pmx-button-power {
> + marvell,pins = "mpp26";
> + marvell,function = "gpio";
> + };
> + };
> +
> + serial@12000 {
> + status = "okay";
> + };
> +
> + sata@80000 {
> + nr-ports = <2>;
> + status = "okay";
> + };
> +
> + i2c@11000 {
> + status = "okay";
> + adt7476: adt7476a@2e {
> + compatible = "adi,adt7476";
> + reg = <0x2e>;
> + };
> + };
> + };
> +
> + gpio_poweroff {
> + compatible = "gpio-poweroff";
> + gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
> + };
> +
> + gpio_keys {
> + compatible = "gpio-keys";
> +
> + button@1{
> + label = "Reset push button";
> + linux,code = <KEY_POWER>;
> + gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
> + };
> + button@2{
> + label = "Power push button";
> + linux,code = <KEY_SLEEP>;
> + gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
> + };
> + };
> +
> + gpio-leds {
> + compatible = "gpio-leds";
> +
> + blue-power {
> + label = "nas220:blue:power";
> + gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "default-on";
> + };
> + };
> +
> + regulators {
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + pinctrl-0 = <&pmx_power_sata0 &pmx_power_sata1>;
> + pinctrl-names = "default";
> +
> + sata0_power: regulator@1 {
> + compatible = "regulator-fixed";
> + reg = <1>;
> + regulator-name = "SATA0 Power";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + regulator-always-on;
> + regulator-boot-on;
> + gpio = <&gpio0 24 0>;
> + };
> +
> + sata1_power: regulator@2 {
> + compatible = "regulator-fixed";
> + reg = <2>;
> + regulator-name = "SATA1 Power";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + regulator-always-on;
> + regulator-boot-on;
> + gpio = <&gpio0 28 0>;
> + };
> + };
> +};
> +
> +&nand {
> + status = "okay";
> + partition@0 {
> + label = "uboot";
> + reg = <0x0 0xa0000>;
> + read-only;
> + };
> +
> + partition@a0000 {
> + label = "env";
> + reg = <0xa0000 0x010000>;
> + };

Is there supposed to be a gap here?

> +
> + partition@c0000 {
> + label = "uimage";
> + reg = <0xc0000 0x500000>;
> + };
> +
> + partition@5c0000 {
> + label = "rootfs";
> + reg = <0x5c0000 0x1a40000>;
> + };
> +};
> +
> +&mdio {
> + status = "okay";
> + ethphy0: ethernet-phy@8 {
> + reg = <8>;
> + };
> +};
> +
> +&eth0 {
> + status = "okay";
> + ethernet0-port@0 {
> + phy-handle = <&ethphy0>;
> + };
> +};
> +
> --

Andrew
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/